All Manuals Close Window

Service Mower


Adjusting Belt Tension

1. Park machine safely. (See Parking Safely in the Safety section.)


MX9238

2. Remove belt covers.

3. Adjust to proper tension. The belt should deflect a maximum of 13 mm (1/2 in.) when a force of 4.5 kg (10 lbs) is applied to the center of the longest span.

To Increase Belt Tension: Turn nut (A - main mower deck drive belt) or (B - spindle drive belt) clockwise.
To Decrease Belt Tension: Turn nut (A - main mower deck drive belt) or (B - spindle drive belt) counterlockwise.

Removing and Installing Mower Deck Drive Belts

1. Park machine safely. (See Parking Safely in the Safety section.)

2. Remove mower deck belt covers.


MX9238

3. Release mower deck drive belt tension by turning the tension adjuster nut (A) counterclockwise.

4. Remove mower deck drive belt (B).

5. Release spindle drive belt tension by turning the tensioner adjuster nut (C).

6. Remove spindle drive belt (D).

7. Install the new spindle drive belt (D) and adjust the drive belt tension.

8. Install new mower deck drive belt (B) and adjust the drive belt tension.

9. Install mower deck drive belt covers.

Checking for Bent Mower Blades

c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades.

1. Park machine safely. (See Parking Safely in the Safety section.)


MIF

2. Measure distance (A) between blade tip and flat ground surface.

3. Turn blade 180°. Measure distance between other blade tip and flat ground surface.

4. Install new blade, if the difference between the two measurements is more than 3 mm (1/8 in.).

Servicing Mower Blades

c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades.

Removing and Installing Mower Blades

1. Park machine safely. (See Parking Safely in the Safety section.)


MX9231

2. Remove nut (A), blade (B), blade washers (C) and bolt (D).

3. Install blade (B), blade washers (C), bolt (D) and secure using nut (A). Tighten nut to 80 N·m (60 lb-ft).

Balancing Mower Blades

1. Clean blade.


M61524

2. Put blade on nail in a vise. Turn blade to horizontal position.

3. Check balance. If blade is not balanced, heavy end of blade will drop.

4. Grind bevel of heavy end. Do not change blade bevel.

Sharpening Blades

c CAUTION: Avoid injury! Always wear safety eye protection when grinding.

· Sharpen blades with grinder, hand file or electric blade sharpener.


M61830

· Keep original bevel (A) when grinding.

· Blade should have 0.40 mm (1/64 in.) cutting edge (B) or less.

· Balance blades before installing.

Replacing Mower Spindle Bearings

1. Park machine safely. (See Parking Safely in the Safety section.)

2. Remove mower deck drive and spindle drive belt.

3. Remove mower blade.


MX9222A

4. Remove upper pulleys:

· Side Spindles: Remove nut (A), spacer (B) and pulley (C).
· Center Spindle: Remove nut (D), drive pulley (E) and spindle pulley (F).

5. Remove spindle shaft (G), lower bearing (H) and spacer (I) from spindle housing (J). Discard bearing.

6. Remove and discard upper bearing (K).

7. Clean entire assembly.

8. Install a new lower bearing (H) and spacer (I) on the spindle shaft (G).

IMPORTANT: Avoid damage! The clearance between the lower bearing and the housing is only 0.05 mm (0.002 in.). Do not force bearing into housing.


9. Install the spindle shaft (G), lower bearing (H) and spacer (I) into the spindle housing (J).

10. Install the upper bearing (K).

11. Install upper pulleys:

· Side Spindles: Install pulley (C), spacer (B) and nut (A). Tighten nut to 80 N·m (60 lb-ft).
· Center Spindle: Install spindle pulley (F), drive pulley (E) and nut (D). Tighten nut to 80 N·m (60 lb-ft).

12. Install mower blade. Tighten nut to 80 N·m (60 lb-ft).

Replacing Mower Deck Idler Pulleys

1. Park machine safely. (See Parking Safely in the Safety section.)

2. Remove the mower deck drive and spindle drive belts.


MX9240

3. Remove mower deck drive tension idler pulley (A) and spindle drive tension idler pulley (B).

4. Install new idler pulleys.

5. Install spindle drive and mower deck drive belts.

6. Adjust belt tension.