Specifications
Engine
Manufacturer Yanmar
Model Number 3TNV76
Type Diesel
Cylinders Three
Rated Engine Speed 3000 rpm
Operating Range 1270 - 3170 rpm
Cooling Type Liquid
Oil Filter Standard Single Element
Air Cleaner Dry Type, Two Stage
Drivetrain
Type 2 Range Hydrostatic
Number of Speeds Infinite
Mechanical Front Wheel Drive (MFWD) Standard
MFWD Capability All Ranges
MFWD Engagement On The Go
Final Drive Spur Gear
Rear Axle Maximum Load 1100 kg (2426 lb)
Front Axle Maximum Load 880 kg (1940 lb)
Electrical System
Type 12 Volt
Battery Size 500 Cold Cranking Amps @ -18°C (0°F)
Alternator 20 amp
Front Wheels and Tires
Standard 23x8.5-12 R3
Optional 23x8.5-12 R4
Rear Wheels and Tires
Standard 31x13.50-15 R3
Optional 12-16.5 R4
Front Tire Inflation Pressures (Maximum)
23x8.5-12 R3 152 kPa (22 psi)
23x8.5-12 R4 241 kPa (35 psi)
Rear Tire Inflation Pressures (Maximum)
31x13.50-15 R3 140 kPa (20 psi)
12-16.5 R4 276 kPa (40 psi)
Fluid Capacities
Fuel Tank 23 L (6.1 gal)
Cooling System 2.4 L (2.5 qt)
Crankcase with Filter 3.2 L (3.4 qt)
Transmission and Hydraulic System 10 L (2.6 gal)
Front Axle 3.4 L (3.6 qt)
Ground Speeds
NOTE: All ground speed calculations shown are with machine equipped with standard tires and operated at 3000 engine rpm.
Forward and Reverse - Range High 0-18.2 km/h (0-11.3 mph)
Forward and Reverse - Range Low 0-7.2 km/h (0-4.5 mph)
Dimensions
NOTE: Machine equipped with standard tires.
Wheelbase 1600 mm (63 in.)
Overall Length with 3-point Hitch 2774 mm (109.2 in.)
Overall Width (Minimum) 1226 mm (48.3 in.)
Tread Width @ Centerline (Minimum)
Front (Only Wide Position Recommended) 790 mm (31.1 in.)
Rear (Only Wide Position Recommended) 952 mm (37.5 in.)
Height From Ground
To Top of Hood 1355 mm (53.3 in.)
To Top of ROPS 2032 mm (80 in.)
Ground Clearance
Front Axle 318 mm (12.5 in.)
Rear Axle 265 mm (10.5 in.)
Turning Radius
With Brakes 2.04 m (6.7 ft)
Without Brakes 2.3 m (7.7 ft)
Weight
Machine equipped with a ROPS, 3-point hitch, standard tires and all fluids. 753 kg (1660 lb)
3-Point Hitch
Type Category 1
Lift Capacity-61 cm (24 in.) behind link arms 522 kg (1150 lb)
Lift Capacity-at link link ends 650 kg (1433 lb)
Torque Values
Metric Torque Values (Dry)
|
Class 7
|
Class 8.8
|
Class 10.9
|
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
M6
|
|
|
11
|
8.1
|
17
|
12.5
|
M8
|
29
|
21
|
35
|
26
|
41
|
30
|
M10
|
59
|
44
|
67
|
49
|
80
|
59
|
M12
|
98
|
72
|
113
|
83
|
132
|
97
|
M14
|
147
|
108
|
167
|
123
|
201
|
148
|
M16
|
206
|
152
|
|
|
|
|
· Use 80% of the value when tightening part is aluminum.
· Use 60% of the value for 4T bolts and lock nuts.
|
Inch Fastener Torque Values (Dry)
|
Grade 21
|
Grade 5
|
Grade 8
|
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
1/4
|
7.4
|
5.5
|
12
|
9
|
17
|
12.5
|
5/16
|
15
|
11
|
24
|
18
|
35
|
26
|
3/8
|
27
|
20
|
45
|
33
|
62
|
46
|
7/16
|
43
|
32
|
70
|
52
|
102
|
75
|
1/2
|
68
|
50
|
108
|
80
|
156
|
115
|
9/16
|
95
|
70
|
156
|
115
|
217
|
160
|
5/8
|
136
|
100
|
217
|
160
|
305
|
225
|
3/4
|
238
|
175
|
|
|
|
|
1
"Grade 2" applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.
|
Metric Torque Values (Lubricated)
|
Class 7
|
Class 8.8
|
Class 10.9
|
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
M6
|
|
|
9
|
6.6
|
13
|
9.6
|
M8
|
23
|
17
|
25
|
18.5
|
29
|
21.4
|
M10
|
44
|
33
|
51
|
38
|
61
|
45
|
M12
|
78
|
58
|
83
|
61
|
103
|
76
|
M14
|
118
|
87
|
127
|
94
|
152
|
112
|
M16
|
167
|
123
|
|
|
|
|
· Use 80% of the value when tightening part is aluminum.
· Use 60% of the value for 4T bolts and lock nuts.
|
Inch Fastener Torque Values (Lubricated)
|
Grade 21
|
Grade 5
|
Grade 8
|
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
N·m
|
lb-ft
|
1/4
|
6.1
|
4.5
|
9.5
|
7
|
13.6
|
10
|
5/16
|
12.2
|
9
|
20
|
15
|
28
|
21
|
3/8
|
22
|
16
|
35
|
26
|
49
|
36
|
7/16
|
35
|
26
|
56
|
41
|
79
|
58
|
1/2
|
53
|
39
|
85
|
63
|
122
|
90
|
9/16
|
76
|
56
|
122
|
90
|
176
|
130
|
5/8
|
106
|
78
|
170
|
125
|
217
|
160
|
3/4
|
190
|
140
|
|
|
|
|
1
"Grade 2" applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.
|
|