All Manuals Close Window

Specifications


Engine

Manufacturer Yanmar

Model Number 3TNV82A-BMJK

Type Diesel

Gross Horsepower 19.8 kW (26.5 hp)

PTO Horsepower 15.3 kW (20.5 hp)

Cylinders Three

Rated Engine Speed 2600 rpm

Operating Range 1000 - 2750rpm

Cooling Type Liquid

Oil Filter Standard Single Element

Air Cleaner Dry Type, Two Stage

Drivetrain

Type 2 Range Hydrostatic

Number of Speeds Infinite

Mechanical Front Wheel Drive (MFWD) Standard

MFWD Capability All Ranges

MFWD Engagement On The Go

Final Drive Spur Gear

Rear Axle Maximum Load 1100 kg (2426 lb)

Front Axle Maximum Load 880 kg (1940 lb)

Electrical System

Type 12 Volt

Battery Size 500 Cold Cranking Amps @ -18°C (0°F)

Alternator 20 amp

Front Wheels and Tires

Standard 24x8.5-14 R3

Optional 23x8.5-12 R4

Rear Wheels and Tires

Standard 36x14.00-15 R3

Optional 14-17.5 R4

Front Tire Inflation Pressures (Maximum)

24x8.5-14 R3 152 kPa (22 psi)

23x8.5-12 R4 241 kPa (35 psi)

Rear Tire Inflation Pressures (Maximum)

36x14.00-15 R3 138 kPa (20 psi)

14-17.5 R4 207 kPa (30 psi)

Tire Loads

NOTE: Maximum load capacity for single tire.

Front (23x8.5-12 R4 6PR) 303 kg (667 lb)

Front (24x8.5-14 R3 4PR) 171 kg (558 lb)

Rear (14-17.5 R4 6PR) 991 kg (2185 lb)

Rear (36x14.00-15 R3 4PR) 535 kg (1179 lb)

Fluid Capacities

Fuel Tank 27 L (7.1 gal)

Cooling System 3.9 L (4.1 qt)

Crankcase with Filter 2.8 L (3.0 qt)

Transmission and Hydraulic System 14.6 L (3.9 gal)

Front Axle 3.4 L (3.6 qt)

Ground Speeds

NOTE: All ground speed calculations shown are with machine equipped with standard tires and operated at 2600 engine rpm.

Forward and Reverse - Range High 0-20.9 km/h (0-13.0 mph)

Forward and Reverse - Range Low 0-7.2 km/h (0-4.5 mph)

Dimensions

NOTE: Machine equipped with standard tires.

Wheelbase 1655 mm (65.2 in.)

Overall Length with 3-point Hitch 2766 mm (108.9 in.)

Overall Width (Minimum) 1295 mm (51.0 in.)

Tread Width @ Centerline (Minimum)

Front (Only Wide Position Recommended) 923 mm (36.3 in.)

Rear (Only Wide Position Recommended) 954 mm (37.6 in.)

Height From Ground

To Top of Hood 1190 mm (47 in.)

To Top of ROPS 2279 mm (90 in.)

Ground Clearance

Front Axle 330 mm (13 in.)

Rear Axle Drawbar 280 mm (11 in.)

Turning Radius

With Brakes 2.3 m (7.5 ft)

Without Brakes 2.5 m (8.2 ft)

Weight

Machine equipped with a ROPS, 3-point hitch, standard tires and all fluids. 846 kg (1865 lb)

3-Point Hitch

Type Category 1

Lift Capacity-61 cm (24 in.) behind link arms 522 kg (1150 lb)

Lift Capacity-at link link ends 650 kg (1433 lb)

Torque Values - Inch Fastener Hardware

Torque Values (Dry)

Torque Values (Lubricated)

Size

Grade 21

Grade 5

Grade 8

Size

Grade 22

Grade 5

Grade 8

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

1/4

7.4

5.5

12

9

17

12.5

1/4

6.1

4.5

9.5

7

13.6

10

5/16

15

11

24

18

35

26

5/16

12.2

9

20

15

28

21

3/8

27

20

45

33

62

46

3/8

22

16

35

26

49

36

7/16

43

32

70

52

102

75

7/16

35

26

56

41

79

58

1/2

68

50

108

80

156

115

1/2

53

39

85

63

122

90

9/16

95

70

156

115

217

160

9/16

76

56

122

90

176

130

5/8

136

100

217

160

305

225

5/8

106

78

170

125

217

160

3/4

238

175

3/4

190

140

• Use 80% of the value when tightening part is aluminum.

• Use 60% of the value for 4T bolts and lock nuts.

• Use 80% of the value when tightening part is aluminum.

• Use 60% of the value for 4T bolts and lock nuts.

1
Grade 2 applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.

2
Grade 2 applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.


Torque Values - Metric Hardware

Torque Values (Dry)

Torque Values (Lubricated)

Size

Class 7

Class 8.8

Class 10.9

Size

Class 7

Class 8.8

Class 10.9

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

N•m

lb-ft

M6

11

8.1

17

12.5

M6

9

6.6

13

9.6

M8

29

21

35

26

41

30

M8

23

17

25

18.5

29

21.4

M10

59

44

67

49

80

59

M10

44

33

51

38

61

45

M12

98

72

113

83

132

97

M12

78

58

83

61

103

76

M14

147

108

167

123

201

148

M14

118

87

127

94

152

112

M16

206

152

M16

167

123

• Use 80% of the value when tightening part is aluminum.

• Use 60% of the value for 4T bolts and lock nuts.

• Use 80% of the value when tightening part is aluminum.

• Use 60% of the value for 4T bolts and lock nuts.