Specifications

Engine

Engine Model Number Honda, GX 120

Engine Type 4-cycle, 1-cylinder, 25° cylinder incline

Piston Displacement 118 cc (7.2 cu in.)

Direction of Rotation of Output Shaft Counterclockwise viewed from shaft side

Adjustment Specifications

Spark Plug Gap 0.7-0.8 mm (0.028-0.031 in.)

Ignition Coil Air Gap 0.4 ± 0.2 mm (0.016 ± 0.008 in.)

Intake Valve Clearance 0.15 ± 0.02 mm (0.006 ± 0.001 in.)

Exhaust Valve Clearance 0.20 ± 0.02 mm (0.008 ± 0.001 in.)

Fuel System

Fuel Types (Recommended):

Regular Grade 87 Octane Unleaded Fuel

Ethanol Blended Fuel (Up to 10%)

MTBE Reformulated Fuel (Up to 15%)

Fuel Delivery Carburetor

Capacities

Engine Oil 0.6 L (0.63 qt)

Fuel Tank 2.5 L (0.66 gal)

Differential Drive Capacity 0.35 L (0.65 pt)

Travel Speeds

Traveling Device (Maximum Forward Speed)

Roller (Rear) 0-5.5 Km/h (0-3.4 mph)

Transport Wheels 0-9.2 km/h (0-5.5 mph)

Tire Dimensions

Transport Tires 4.1-6 (2 pr.) (Tubeless)

Pressure (Standard Pneumatic) 125-140 kPa (18-20 psi)

Dimensions

Height (With tires installed) 119cm (37 in.)

Length (With tires installed) 94mm (37 in.)

Width (With tires installed)

180C 84.5 mm (33.3 in.)

220C 94.6 mm (37.3 in.)

260C 104.8 mm (41.3 in.)

Weight (Less brush drive, transport wheels and with grass catcher)

180C 92.5 kg (204 lb)

220C 99.5 kg (219 lb)

260C 105 kg (237 lb)

Cutting Unit

Greens Tender Conditioner (Optional)

18 inch 60 mm (2-3/8 in.) diameter, 61 blades

22 inch 60 mm (2-3/8 in.) diameter, 75 blades

26 inch 60 mm (2-3/8 in.) diameter, 89 blades

Rotary Brush (Optional) Interlocked with reel, rotation in reverse direction 60 mm (2-3/8 in.) diameter

Material of Vertical Cutter Blades Special hardened carbon steel star shaped 0.6 mm (1/32 in.)

Adjustable Brush or Cutter Height 10mm (13/32 in.) below to 5.5 mm (7/32 in.) above cut

Gear Drive (Optional) Gear driven from reel shaft opposite direction of reel rotation, powers brush or cutter

Frequency of Clip

11 Blade 4.62 mm (0.182 in.)

9 Blade 5.64 mm (0.222 in.)

7 Blade 7.26 mm (0.286 in.)

Cutting Height (Minimum)

Standard Bed Knife 3.2 mm (1/8 in.)

Optional Tournament Bed Knife 2.8 mm (7/64 in.)

Optional Low-Cut Bed Knife 2.0 mm (5/64 in.)

Cutting Width

180C 457 mm (18 in.)

220C 559 mm (22 in.)

260C 660 mm (26 in.)

Traction Drum Dual aluminum traction

Clutches

Transport Belt tension

Cutter Jaw-type clutch “on/off”

Brush/GTC Jaw-type clutch “on/off”

Reel

Diameter 127 mm (5 in.)

Standard Number of Blades 180C (11 blades) 220C (11 blades) 260C (11 or 7 blades)

Optional Number of Blades 220C (9 blades)

Material Special hardened alloy

Miscellaneous

Park Brake Band type brake, lever action

Recommended Lubricants

Engine Oil John Deere Plus–4®

Gear Case Oil John Deere Hy-Gard®

Grease See Service Lubrication Section

(Specifications and design subject to change without notice.)