
Service Intervals
Servicing Your Machine
IMPORTANT: Avoid damage! Operating in extreme conditions may require more frequent service intervals:
• Engine components may become dirty or plugged when operating in extreme heat, dust or other severe conditions.
• Engine oil can degrade if machine is operated constantly at slow or low engine speeds or for frequent short periods of time.
|
Please use the following timetables to perform routine maintenance on your machine.
Break-In
After First 10 Hours of Operation
• Check brakes and neutral lock linkages (adjust if needed).
• Check speed control pedals (adjust if needed).
• Check and tighten drive wheel hardware to specification.
After First 50 Hours of Operation
• Change engine oil and filter.
• Change transaxle oil and filter.
• Inspect alternator belt for wear and proper tension.
Before Each Use
• Check engine oil and coolant fluid levels.
• Check hydraulic and transaxle oil levels.
• Check brakes, speed control and neutral start switch functions.
After Each Use
• Clean debris from operator station and attachment.
• Clean air intake screen and radiator/oil cooler fins.
• Clean debris from alternator cooling holes.
• Check and drain water from fuel filter/water separator (1435).
• Check and drain water from water separator (1445, 1545, 1565).
• Check for loose, missing, or damaged parts.
• Fill fuel tank.
Every 50 Hours or Yearly
• Check for loose or missing hardware.
• Inspect tires and check air pressure.
• Check and tighten drive wheel hardware to specification.
• Check rear axle oil level. (4WD only).
• Grease rear axle pivot pin (1 place).
• Grease engine drive shaft (1 place).
• Grease rear axle steering spindles (2WD) (2 places).
• Grease PTO shaft (3 Places).
• Clean battery and check battery fluid level.
Every 100 Hours
• Grease steering cylinder (2 places).
• Grease tie rod ends (2 places).
• Grease hydrostatic linkage (1 place).
• Grease turn brake pedals (2 places).
• Blow out oil cooler/radiator fins with pressurized air.
• Check speed control, brake, & neutral lock linkages. Adjust if needed.
• Check coupler, replace if necessary.
Every 200 Hours
• Change engine oil and filter.
• Check air intake and coolant hoses and tighten clamps.
• Check alternator belt wear and tension.
• Inspect alternator belt for wear and proper tension.
• Gas Models: Clean and gap spark plugs.
• Gas Models: Check and/or replace air cleaner elements.
Every 400 Hours
• Change transaxle oil and filter.
Every 500 Hours
• Replace fuel filter, if not replaced within last year.
• Check roll-over protection system (ROPS) hardware for proper torque.
• Change rear axle oil (4WD Model Only).
• Check rear axle pivot pin.
• Check brakes and neutral lock linkage. See Technical Manual or your John Deere dealer.)
• Check toe-in adjustment. See Technical Manual or your John Deere dealer.)
• Gas Models: Replace and gap spark plugs.
• Diesel Models: Check valve clearance. (See Technical Manual or your John Deere dealer.)
Yearly
• Check coolant freeze point and clarity.
• Replace fuel filter, at least once per season.
• Change engine oil and filter, at least once per season
Every 1500 Hours or Two Years
• Diesel Model: Check fuel injectors. (See the Technical Manual or your John Deere dealer.)
Every 2000 Hours or Two Years
• Change engine coolant and thermostat, if using COOL-GARD™ CONCENTRATE ANTIFREEZE (TY16036).
Every 3000 Hours or Three Years
• Change engine coolant and thermostat, if using COOL-GARD™ PREDILUTED ANTIFREEZE (TY16034).
Every 3000 Hours
• Diesel Models: Check fuel injection pump. (See the Technical Manual or your John Deere dealer.)
As Needed
• Replace fuses, light bulbs, and battery.
• Replace radiator hoses.
• Adjust alternator belt tension or replace belt.
• Check and adjust park brake. (See the Technical Manual or your John Deere dealer.)
• Check/tighten hardware.
• Check and/or replace air cleaner elements.
• Clean rubber dust unloading valve.
• Diesel Models: Check and drain fuel filter sediment bowl.
• Service or replace battery.
|