Specifications

Specifications

Engine

Manufacturer Yanmar

Model Number 3TNV84T-KJT

Type Diesel

Gross Horsepower 30.2 kW (41 hp)

Manufacturer's Estimated PTO Horsepower 24.2 kW (32.5 hp)

Low Idle Speed 950 rpm

Rated Engine Speed 2800 rpm

High Idle Speed 2975 rpm

Operating Range 1000 - 2975 rpm

Engine Torque @ Rated Speed 111 Nm (80.2 lb-ft)

Maximum Torque @ 1900 rpm 127 Nm (91.8 lb-ft)

Displacement 1.5 L (91.5 cu in.)

Cylinders 3

Bore and Stroke 84 x 90 mm (3.3 x 3.54 in.)

Compression Ratio 19:1

Lubrication Pressurized

Cooling System Water Pump

Oil Filter Single Element

Air Cleaner Dry Type with Safety Element

Starting Aid Air Heater

Electrical System

Type 12 Volt

Battery Capacity 500 Cold Cranking Amps at -18C (0F)

Battery Size 22NF

Alternator 40 Amp

Starter Size 1.4 kW (1.9 hp)

Fuel System

Fuel Filter Replaceable Element

Fuel Diesel

Fuel Pump In-Line with Electric Shutoff

Fuel Delivery Direct Injection, Self Bleeding

Drive Train

Transmission 2 Range Hydrostatic

Number Of Speeds Infinite Forward, Infinite Reverse

Mechanical Front Wheel Drive Standard

Capability for MFWD All Ranges

Rear Final Drive Type Spur Gear

Differential Lock Ball, Ramp and Pin

Brakes Type Wet Disk

Steering Power, Hydrostatic

Front Axle Operating Capacity 1450 kg (3197 lb)

Rear Axle Operating Capacity 1815 kg (4002 lb)

Drawbar Tongue Capacity 400 kg (882 lb)

Hydraulic System

Type of System Open Center

Power Steering Standard

Implement and Steering Pump Type Dual Tandem Gear Pump

Working Pressure 17237 kPa (2500 psi)

Steering Pressure 10342 kPa (1500 psi)

Pump Capacity (Main) @ Rated Speed 34.7 L/min (9.2 gpm)

Pump Capacity (Power Steering) @ Rated Speed 21.6 L/min (5.7 gpm)

Total Flow of Pumps @ Rated Speed 56.2 L/min (14.8 gpm)

3 Point Hitch

Type Category 1

Lift Capacity (24-in. behind link arms) 999 kg (2200 lb)

Dimension - Lower Link Ball Socket ID 22 mm (7/8 in.)

Dimension - Upper Link Pin Hole ID 19 mm (3/4 in.)

Dimension - Normal Width @ Lower Hitch Pins 68.6 cm (27 in.)

Dimension - Normal Height From Center Pin to Hitch Pin 45.7 cm (18 in.)

PTO

Type Independent

Clutch Type Wet Disk

Speed (Rear PTO rpm @ Rated Engine Speed) 540 rpm

Mid PTO Available No

Fluid Capacities

Fuel Tank 43.5 L (11.5 gal)

Cooling System 5.3 L (1.4 gal)

Crankcase w/ Filter 4.3 L (4.5 qt)

Transmission and Hydraulic System 31.4 L (8.3 gal)

Front Axle 4.5 L (1.2 gal)

Ground Speeds

Note: All ground speeds shown are with machine equipped with standard tires and operated at 2800 engine RPM.

Forward (Low Range) 9.2 km/h (5.7 mph)

Forward (High Range) 20.1 km/h (13 mph)

Reverse (Low Range) 8.9 km/h (5.5 mph)

Reverse (High Range) 19.4 km/h (12.6 mph)

Tires

Front 10.0-16.5 6PR R4

Front 8.00-16 6PR R1

Rear 17.5L-R24 8PR R4

Rear 14.9-24 4PR R1

Tire Inflation Pressures

NOTE: Minimum / Maximum pressures given. Minimum pressure is for unloaded, unballasted tractor.

Front (10.0-16.5 6PR R4) 103 kPa/310 kPa (15 psi/45 psi)

Front (8.00-16 6PR R1) 89 kPa/190 kPa (13 psi/27 psi)

Rear (17.5L-R24 6PR R4) 138 kPa/180 kPa (20 psi/26 psi)

Rear (14.9-24 4PR R1) 82 kPa/241 kPa (12 psi/35 psi)

Tire Loads

NOTE: Maximum load capacity for single tire.

Front (10.0-16.5 6PR R4) 1078 kg (2377 lb)

Front (8.00-16 6PR R1) 617 kg (1360 lb)

Rear (17.5L-R24 8PR R4) 2531 kg (5581 lb)

Rear (14.9-24 4PR R1) 1069 kg (2357 lb)

Dimensions

Wheelbase 1727 mm (68 in.)

Overall Length w/ 3-Point Hitch 3053 mm (120.2 in.)

Overall Width (minimum with R1 rear tires) 1601 mm (63 in.)

Overall Width (maximum with R4 rear tires) 1672 mm (65.8 in.)

Height From Ground

To Top of Hood 1450 mm (57.1 in.)

To Top of ROPS 2226 mm (87.6 in.)

Weight

With ROPS, 3-Point Hitch and all fluids 1315 kg (2899 lb)

Recommended Lubricants

Engine Oil John Deere Plus-50 or TORQ-GARD SUPREME (See SERVICE ENGINE for more information.)

Grease John Deere Multi-Purpose SD Polyurea Grease

John Deere Multi-Purpose HD Lithium Complex Grease

Transmission Oil Low Viscosity HY-GARD (JDM J20D)

Front Axle Oil Low Viscosity HY-GARD (JDM J20D)

(Specifications and design subject to change without notice.)

Torque Values - Metric Hardware


Torque Values (Dry)							Torque Values (Lubricated)
Size	Class 7		Class 8.8		Class 10.9		Size	Class 7		Class 8.8		Class 10.9
	Nm	lb-ft	Nm	lb-ft	Nm	lb-ft		Nm	lb-ft	Nm	lb-ft	Nm	lb-ft
M6			11	8.1	17	12.5	M6			9	6.6	13	9.6
M8	29	21	35	26	41	30	M8	23	17	25	18.5	29	21.4
M10	59	44	67	49	80	59	M10	44	33	51	38	61	45
M12	98	72	113	83	132	97	M12	78	58	83	61	103	76
M14	147	108	167	123	201	148	M14	118	87	127	94	152	112
M16	206	152					M16	167	123
Use 80% of the value when tightening part is aluminum. Use 60% of the value for 4T bolts and lock nuts.							Use 80% of the value when tightening part is aluminum. Use 60% of the value for 4T bolts and lock nuts.

Torque Values - Inch Fastener Hardware


Torque Values (Dry)							Torque Values (Lubricated)
Size	Grade 2¹		Grade 5		Grade 8		Size	Grade 2²		Grade 5		Grade 8
	Nm	lb-ft	Nm	lb-ft	Nm	lb-ft		Nm	lb-ft	Nm	lb-ft	Nm	lb-ft
1/4	7.4	5.5	12	9	17	12.5	1/4	6.1	4.5	9.5	7	13.6	10
5/16	15	11	24	18	35	26	5/16	12.2	9	20	15	28	21
3/8	27	20	45	33	62	46	3/8	22	16	35	26	49	36
7/16	43	32	70	52	102	75	7/16	35	26	56	41	79	58
1/2	68	50	108	80	156	115	1/2	53	39	85	63	122	90
9/16	95	70	156	115	217	160	9/16	76	56	122	90	176	130
5/8	136	100	217	160	305	225	5/8	106	78	170	125	217	160
3/4	238	175					3/4	190	140
Use 80% of the value when tightening part is aluminum. Use 60% of the value for 4T bolts and lock nuts.							Use 80% of the value when tightening part is aluminum. Use 60% of the value for 4T bolts and lock nuts.

¹

Grade 2 applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.

²

Grade 2 applies for hex cap screws (not hex bolts) up to 152mm (6 in.) long.

Copyright © 2011 Deere & Company. All Rights Reserved.

About Our Site | Privacy | Legal