Machine Folded-24 Row
IMPORTANT:
Before performing any of these checks, be sure hydraulic SCV's are set to maximum flow, frame control console has power (backlight is on), cleanout switch is set to PLANT position, and the proper buttons are being pushed for the desired function to be performed.
|
|
|
Machine not functioning. (Tractor engine must be running.)
|
Control console not powered.
|
Check electrical connections at 7-pin connector (tractor and machine side).
|
|
|
|
Check inline fuses to frame control box.
|
|
|
Pressure and return hoses not fully engaged in SCV outlets.
|
-
|
|
Machine will not unfold.
|
-
|
Refer to UNFOLDING PLANTER in Transporting section for proper procedure to unfold planter.
|
|
|
Y8 solenoid not energizing.
|
Check for 12V at the solenoid.
|
|
|
|
Check solenoid.
|
|
|
Y8 valve stuck closed.
|
Clean or replace valve.
|
|
Machine unfolds when not selected.
|
NOTE:
If machine is more than half way unfolded (pivot area frame fold switch is closed), the frame control box in PLANT, and machine is lowered, the machine will unfold. This is normal operation.
Frame fold switch malfunctioning (switch located in pivot area).
|
See your John Deere dealer.
|
|
|
Y8 valve is stuck open.
|
Check for 12V at the solenoid.
|
|
|
|
Clean or replace valve.
|
|
|
OUO6435,0001EED -19-02OCT06-1/3
|
| Symptom |
Problem |
Solution |
|
Machine will not raise or lower.
|
Frame control box PLANT/TRANS switch is in PLANT position.
|
Place switch in TRANS position.
|
|
|
Check pins 1 and 7 on tractor/planter 7 pin connector for 12 volts.
|
See your John Deere Dealer.
|
|
|
Inspect F3 10 amp fuse in frame control harness.
|
Replace as needed.
|
|
|
One or more solenoids; Y1, Y22, Y23, Y24, Y25 may not be energizing or may be stuck.
|
Check for 12V at the solenoid.
|
|
|
|
Clean or replace valves.
|
|
|
Check K34 relay.
|
See RELAY AND FUSE LOCATION in Service section. Replace as needed.
|
|
Machine will not raise to high lift.
|
One or more solenoids; Y22, Y23, Y24 or Y25 may not be energizing or may be stuck.
|
Check for 12V at the solenoids.
|
|
Machine unlevel.
|
Hydraulics out of phase.
|
Lower machine in folded position. Refer to LOWERING/RAISING MACHINE IN TRANSPORT POSITION FOR FILLING AND/OR SERVICING in Transporting section or refer to decal on frame control console.
|
|
In transport position, wing wheels won't retract.
|
One or more solenoids; Y22, Y23, Y24 or Y25 and/or wing rephasing valves malfunctioning.
|
Verify Y22, Y23, Y24 or Y25 are being energized and repair as necessary.
|
|
|
|
Clean or replace Y22, Y23, Y24 or Y25 and rephasing valve.
|
|
|
|
See your John Deere dealer.
|
|
In transport position, wing wheels won't extend.
|
One or more solenoids; Y22, Y23, Y24 or Y25 and/or wing rephasing valves malfunctioning.
|
Verify Y22, Y23, Y24 and/or Y25 are being energized and repair as necessary.
|
|
|
OUO6435,0001EED -19-02OCT06-2/3
|
| Symptom |
Problem |
Solution |
|
|
|
Clean or replace Y22, Y23, Y24 and/or Y25 and rephasing valve.
|
|
|
|
See your John Deere dealer.
|
|
In transport position, main frame wheels won't retract.
|
One or more solenoids; Y22, Y23, Y24 or Y25 and/or wing rephasing valves malfunctioning.
|
Verify Y22, Y23, Y24 and/or Y25 are being energized and repair as necessary.
|
|
|
|
Clean or replace Y22, Y23, Y24 and/or Y25 and rephasing valve.
|
|
|
|
See your John Deere dealer.
|
|
In transport position, main frame wheels won't extend.
|
One or more solenoids; Y22, Y23, Y24 and/or Y25 and/or wing rephasing valves malfunctioning.
|
Verify Y22, Y23, Y24 and/or Y25 are being energized and repair as necessary.
|
|
|
|
Clean or replace Y22, Y23, Y24 and/or Y25 and rephasing valve.
|
|
|
|
See your John Deere dealer.
|
|
|
OUO6435,0001EED -19-02OCT06-3/3
|
|