24 Row FoldedIMPORTANT: Before performing any of these checks, verify hydraulic SCVs are set to maximum flow, frame control console has power (backlight is on), cleanout switch is set to “Plant” position, and the proper buttons are pushed for the desired function . | Symptom | Problem | Solution | Machine not functioning. (Tractor engine must be running.) | Control console not powered. | Check electrical connections at 7-pin connector (tractor and machine side). Check inline fuses to frame control box. | | | Pressure and return hoses not fully engaged in SCV outlets. | Verify connections. |
Machine fails to unfold. | Not following procedure. | See UNFOLD MACHINE in Operate Machine section for proper procedure to unfold planter. | | | Y8 solenoid not energizing. | Check for 12 volts at the solenoid. Check solenoid. | | | Y8 valve stuck closed. | Clean or replace valve. |
Machine unfolds when not selected. | If machine is more than half way unfolded (pivot area frame fold switch is closed), the frame control box in “Plant”, and machine is lowered, the machine unfolds. This is normal operation.Frame fold switch malfunction (switch located in pivot area). | See your John Deere dealer. | | | Y8 valve is stuck open. | Check for 12 volts at the solenoid. Clean or replace valve. |
Machine fails to raise or lower. | Frame control box PLANT-TRANS switch is in “Plant” position. | Place switch in “Trans” position. | | | Check pins 1 and 7 on tractor to planter 7 pin connector for 12 volts. | See your John Deere Dealer. | | | Inspect F3, 10 amp fuse in frame control harness. | Replace as needed. | | | One or more solenoids; Y1, Y22, Y23, Y24, Y25 not energizing or stuck. | Check for 12 volts at the solenoid. Clean or replace valves. | | | Check K34 relay. | See RELAY AND FUSE LOCATION in Service and Adjustments section. Replace as needed. |
Machine fails to raise to high lift. | One or more solenoids; Y22, Y23, Y24, or Y25 not energizing or stuck. | Check for 12 volts at the solenoids. |
Machine unlevel. | Hydraulics out of phase. | Lower machine in folded position. See LOWER OR RAISE MACHINE IN TRANSPORT POSITION FOR FILL OR SERVICE in Operate Machine section or refer to decal on frame control console. |
In transport position, wing wheels fail to retract. | One or more solenoids; Y22, Y23, Y24, or Y25 or wing rephasing valves malfunction. | Verify Y22, Y23, Y24, or Y25 are being energized and repair as necessary. Clean or replace Y22, Y23, Y24, or Y25 and rephasing valve. See your John Deere dealer. |
In transport position, wing wheels fail to extend. | One or more solenoids; Y22, Y23, Y24, or Y25 or wing rephasing valves malfunction. | Verify Y22, Y23, Y24, or Y25 are being energized and repair as necessary. Clean or replace Y22, Y23, Y24, or Y25 and rephasing valve. See your John Deere dealer. |
In transport position, main frame wheels fail to retract. | One or more solenoids; Y22, Y23, Y24, or Y25 or wing rephasing valves malfunctioning. | Verify Y22, Y23, Y24, or Y25 are being energized and repair as necessary. Clean or replace Y22, Y23, Y24, or Y25 and rephasing valve. See your John Deere dealer. |
In transport position, main frame wheels fail to extend. | One or more solenoids; Y22, Y23, Y24, or Y25 or wing rephasing valves malfunctioning. | Verify Y22, Y23, Y24, or Y25 are being energized and repair as necessary. Clean or replace Y22, Y23, Y24, or Y25 and rephasing valve. See your John Deere dealer. |
| OUO6435,0001EED-19-20090526 |
|