Diagnostic Trouble Codes on Basic Control Unit / Hitch Control Unit (BCU)

Light Diagnostic Trouble Codes Description
Alert Type ShortDesc LongDesc
blue BCU 000084.02 Transmission output speed sender, fault in electrical circuit
yellow BCU 000168.16 System voltage too high (engine running)
yellow BCU 000168.17 System voltage too low (engine speed over 1500 rpm)
yellow BCU 000168.18 System voltage too low (engine speed up to 1500 rpm)
blue BCU 000186.02 Rear PTO speed sender, fault in electrical circuit
blue BCU 000186.15 Rear PTO speed is still registered after PTO has been switched off
blue BCU 000186.17 Rear PTO speed is not being registered
blue BCU 000190.02 Engine speed sender, fault in electrical circuit
blue BCU 000629.12 Control unit internal fault
blue BCU 000639.12 Control unit internal fault
blue BCU 000639.13 29-BIT CAN BUS, high error rate
blue BCU 000639.19 29-BIT CAN BUS, very high error rate
blue BCU 000746.31 Differential lock solenoid valve, fault in electrical circuit
blue BCU 000980.07 Rear PTO, switch fault
blue BCU 001882.02 Front PTO speed sender, fault in electrical circuit
blue BCU 001882.15 Front PTO speed is still registered after PTO has been switched off
blue BCU 001882.17 Front PTO speed not registered
blue BCU 001893.07 Front PTO, switch fault
blue BCU 299780.07 Turn signal switch, malfunction
- BCU 302001.31 INFORMATION FOR OPERATOR: 250-hour service!
- BCU 302002.31 INFORMATION FOR OPERATOR: 500-hour service!
- BCU 302003.31 INFORMATION FOR OPERATOR: 750-hour service!
- BCU 302004.31 INFORMATION FOR OPERATOR: 1500-hour service!
- BCU 302071.31 INFORMATION FOR OPERATOR: Switch off the rear PTO switch!
blue BCU 302073.31 Rear PTO solenoid valve, fault in electrical circuit
- BCU 302077.31 INFORMATION FOR OPERATOR: Sit on seat or switch off rear PTO!
blue BCU 302080.31 Differential lock, switch fault
- BCU 302082.31 INFORMATION FOR OPERATOR: Actuate the front-wheel drive switch!
blue BCU 302085.31 FWD, switch fault
blue BCU 302086.31 Solenoid valve for FWD clutch, fault in electrical circuit
blue BCU 302106.31 Control unit internal fault
blue BCU 302120.31 Front PTO solenoid valve, fault in electrical circuit
blue BCU 302123.31 Switch signal from forward or reverse travel does not match the signal from the not-neutral switch
blue BCU 302124.31 Alternator relay, fault in electrical circuit
blue BCU 302131.31 Fault in turn signal circuit
blue BCU 302132.31 Hazard warning flashers, fuses F03/04 and/or F03/07 is/are blown
blue BCU 302134.31 HMS program switch is faulty
blue BCU 302240.31 Control unit is connected to the wrong harness connector
blue BCU 303027.31 Hitch control unit, calibration not successful
blue BCU 303028.31 Hitch control unit not calibrated
blue BCU 303037.03 5-volt power supply is too high
blue BCU 303037.04 5-volt power supply is too low
blue BCU 303041.02 Coil 1 of stepper motor, open circuit
blue BCU 303042.02 Coil 2 of stepper motor, open circuit
blue BCU 303043.02 Coil 1 of stepper motor, fault in electrical circuit
blue BCU 303044.02 Coil 2 of stepper motor, fault in electrical circuit
yellow BCU 303045.04 System voltage too low
yellow BCU 303047.03 System voltage too high
blue BCU 303049.02 Conflicting signals from quick raise/lower switch and remote switch
blue BCU 303049.03 Rocker switch for quick withdrawal, signal voltage too high

 

OU12401,0000B28 -19-01JUL02-1/2

Light Diagnostic Trouble Codes Description
blue BCU 303049.04 Rocker switch for quick withdrawal, signal voltage too low
blue BCU 303051.03 Left draft sensor, signal voltage too high
blue BCU 303051.04 Left draft sensor, signal voltage too low
blue BCU 303052.03 Right draft sensor, signal voltage too high
blue BCU 303052.04 Right draft sensor, signal voltage too low
blue BCU 303053.03 Sensitivity potentiometer, signal voltage too high
blue BCU 303053.04 Sensitivity potentiometer, signal voltage too low
blue BCU 303054.03 Depth setting potentiometer, signal voltage too high
blue BCU 303054.04 Depth setting potentiometer, signal voltage too low
blue BCU 303055.03 Position sensor, signal voltage too high
blue BCU 303055.04 Position sensor, signal voltage too low
blue BCU 303056.03 Lift limit potentiometer, signal voltage too high
blue BCU 303056.04 Lift limit potentiometer, signal voltage too low
blue BCU 303057.03 Rate-of-drop potentiometer, signal voltage too high
blue BCU 303057.04 Rate-of-drop potentiometer, signal voltage too low
blue BCU 303058.02 Remote control switch, faulty signal
blue BCU 303060.02 Stepper motor, deadband step is out of specification
blue BCU 303177.18 Oil temperature too low during calibration
blue BCU 303251.02 Left draft sensor, distorted signal during calibration
blue BCU 303251.03 Left draft sensor, signal voltage too high during calibration
blue BCU 303251.04 Left draft sensor, signal voltage too low during calibration
blue BCU 303252.02 Right draft sensor, distorted signal during calibration
blue BCU 303252.03 Right draft sensor, signal voltage too high during calibration
blue BCU 303252.04 Right draft sensor, signal voltage too low during calibration
blue BCU 303255.03 Position sensor, signal voltage too high during calibration
blue BCU 303255.04 Position sensor, signal voltage too low during calibration
blue BCU 303260.16 Stepper motor, deadband step (raising) is above the permitted upper threshold during calibration
blue BCU 303260.18 Stepper motor, deadband step (raising) is below the permitted lower threshold during calibration
blue BCU 303261.16 Stepper motor, deadband step (lowering) is above the permitted upper threshold during calibration
blue BCU 303261.18 Stepper motor, deadband step (lowering) is below the permitted lower threshold during calibration

 

OU12401,0000B28 -19-01JUL02-2/2