Digital Display

The digital display shows travel speed, engine speed and PTO speed; it also indicates the time of day (clock) and hours of operation. On tractors with PowrQuad Plus or AutoQuad II transmissions, it also indicates which gear is selected.

After the ignition is switched on, it shows the operating hours, before changing to display the travel speed once the tractor is moving.

Roll-mode switch (A) changes the display from one mode to the next.

AG,OU12401,178 -19-01DEC00-1/8

Travel speed is indicated either as "km/h" or "MPH".

NOTE: On tractors without creeper transmission, the display changes to 0 as soon as travel speed drops below 0.5 km/h (0.3 mph).

On tractors with creeper transmission, the display changes to 990 m/h (0.600 mph) as soon as travel speed drops below 1 km/h (0.6 mph).

NOTE: If, on level terrain, the display on a tractor with a 50 km/h (31 mph) transmission shows a speed in excess of 50.5 km/h (31.4 mph), consult your John Deere dealer.

If the tractor drives and the display shows 0.0 km/h (0.0 mph), consult your John Deere dealer.

AG,OU12401,178 -19-01DEC00-2/8

The engine symbol appears and engine speed is displayed.

AG,OU12401,178 -19-01DEC00-3/8

The PTO symbol appears. An arrow indicates "front PTO" (if equipped). PTO speed is displayed.

NOTE: With the engine running, if PTO speed exceeds 620 rpm, it is displayed intermittently (flashing) regardless of the display selected. This warns of the possible danger if a 540 rpm PTO is being used. On tractors with Dual Gauge Plus II, code 140 is also displayed. The "CAUTION" light also flashes. Actuating the roll-mode switch again causes the flashing display to stop. The display stops flashing automatically whenever PTO speed drops below 590 rpm.

AG,OU12401,178 -19-01DEC00-4/8

The clock symbol appears and the time of day is displayed. Can be reset using the two keys below the display.

AG,OU12401,178 -19-01DEC00-5/8

When the ignition is switched on, the display shows the number of hours operated by the engine.

AG,OU12401,178 -19-01DEC00-6/8

The transmission symbol appears; the gear that is currently selected is displayed.

On tractors with Dual Gauge Plus II, the direction of travel is also displayed. On tractors with AutoQuad transmission, the word "AUTO" appears as soon as this function is selected.

AG,OU12401,178 -19-01DEC00-7/8

If the automatic mode is selected, area (A) will show the following:

• If Load Control is selected and engine load is controlled, the transmission icon appears together with the letter "A".
• If Eco mode is selected and engine speed is reduced electronically, an engine icon appears together with the letter "E".

The selected top speeds in the forward and reverse speed ranges are shown in area (B). The selected direction of travel is shown by the tractor icon and an arrow (C).

If the reverse drive lever is placed in the corner Park position, area (C) will show the following:

• While the tractor is still moving, the display alternates between the direction of travel arrow and the letter "P".
• When the tractor is stopped, "P" is displayed.

If the reverse drive lever is placed in the center Park position, area (C) will show the following:

• While the tractor is still moving, the letter "N" is displayed.
• When the tractor is stopped, the tractor icon and both direction arrows are displayed. After a brief interval, the letter "P" is displayed.

If the tractor is in "Power Zero" (reverse drive lever is held between the two directions of travel), both direction arrows and the tractor icon are displayed. Additionally, the current speed ranges are displayed (1 and 2).

If the reverse drive lever is moved to the neutral position, the letter "N" is displayed.

If the reverse drive lever is in the center Park position or in neutral, area (B) alternates between the set top speeds for forward and reverse.

If the reverse drive lever is in the position for forward or reverse travel, the relevant top speed is displayed (either forward speed or reverse speed).

AG,OU12401,178 -19-01DEC00-8/8