Travel Speeds, 6510 and 6610 Tractors (24/24* Transmission)

50 km/h (31 mph); rated engine speed 2300 rpm; 18.4-38 tires  
(50 km/h; 31 mph will be reached at less than 2300 rpm) Additional gears with creeper transmission
Range
 Gear
 km/h
 mph
Range
 Gear
 km/h
 mph
  
A 1 1.8 1.1   A 1 0.18 0.11  
  2 2.2 1.4     2 0.22 0.14  
  3 2.6 1.6     3 0.26 0.16  
  4 3.2 2.0     4 0.32 0.20  
B 1 4.6 2.9   B 1 0.46 0.29  
  2 5.5 3.4     2 0.55 0.34  
  3 6.8 4.2     3 0.66 0.41  
  4 8.0 5.0     4 0.81 0.50  
C 1 7.3 4.5   C 1 0.74 0.46  
  2 8.8 5.5     2 0.89 0.55  
  3 10.6 6.6     3 1.06 0.66  
  4 13.0 8.1     4 1.30 0.81  
D 1 12.1 7.5            
  2 14.6 9.1            
  3 17.5 10.9            
  4 21.4 13.3            
E 1 19.4 12.1            
  2 23.4 14.5            
  3 28.8 17.9            
  4 34.3 21.3            
F 1 28.4 17.7            
  2 34.2 21.3            
  3 41.0 25.5            

4
 50.0
 31.1





A R1 2.1 1.3   A R1 0.21 0.13  
  R2 2.6 1.6     R2 0.26 0.16  
  R3 3.1 1.9     R3 0.31 0.19  
  R4 3.8 2.4     R4 0.38 0.24  
B R1 5.4 3.4   B R1 0.54 0.34  
  R2 6.5 4.0     R2 0.65 0.40  
  R3 7.8 4.8     R3 0.78 0.48  
  R4 9.5 5.9     R4 0.96 0.60  
C R1 8.7 5.4   C R1 0.87 0.54  
  R2 10.5 6.5     R2 1.05 0.65  
  R3 12.5 7.8     R3 1.26 0.78  
  R4 15.4 9.6     R4 1.54 0.96  
D R1 14.4 8.9            
  R2 17.3 10.8            
  R3 20.7 12.9            
  R4 25.4 15.8            
E* R1 23.0 14.3            
  R2 27.7 17.2            
  R3 33.2 20.6            
  R4 40.7 25.3            
F* R1 33.7 20.9            
  R2 40.6 25.2            
  R3 48.6 30.2            

R4
 50.0 31.1





 

AG,OU12401,112 -19-29JAN00-1/2

Other tires (supplied by factory):
16.9-38 3.0% slower 460/85-38 same
420/85-38 3.0% slower 520/70-38 same
480/70-38 3.0% slower 600/65-38 same
540/65-38
 3.0% slower

* Depending on equipment and legal requirements, there may in certain circumstances be only 16 reverse gears.

 

NOTE: The ground travel speeds shown in the table are theoretical. The actual speeds vary with rolling circumference, load, tire pressure, make

of tire, wheel slip etc. If the precise speed is required for specific applications, then it must be obtained by measurement.

AG,OU12401,112 -19-29JAN00-2/2