Travel Speeds, 6510 and 6610 Tractors (24/24* Transmission)

40 km/h (25 mph); rated engine speed 2300 rpm; 16.9-38 tires  
  Additional gears with creeper transmission
Range
Gear
km/h
mph

Range
Gear
km/h
mph
 
A 1 1.4 0.9   A 1 0.14 0.09  
  2 1.8 1.1     2 0.18 0.11  
  3 2.1 1.3     3 0.21 0.13  
  4 2.6 1.6     4 0.26 0.16  
B 1 3.6 2.2   B 1 0.36 0.22  
  2 4.3 2.7     2 0.44 0.27  
  3 5.3 3.3     3 0.53 0.33  
  4 6.4 4.0     4 0.64 0.40  
C 1 5.9 3.7   C 1 0.59 0.37  
  2 7.0 4.4     2 0.71 0.44  
  3 8.5 5.3     3 0.85 0.53  
  4 10.3 6.4     4 1.04 0.65  
D 1 9.7 6.0            
  2 11.7 7.3            
  3 13.9 8.6            
  4 17.0 10.6            
E 1 15.5 9.6            
  2 18.7 11.6            
  3 22.3 13.9            
  4 27.3 17.0            
F 1 22.7 14.1            
  2 27.3 17.0            
  3 32.7 20.3            

4
40.0
24.9






A R1 1.8 1.1   A R1 0.18 0.11  
  R2 2.1 1.3     R2 0.21 0.13  
  R3 2.5 1.6     R3 0.25 0.16  
  R4 3.0 1.9     R4 0.30 0.19  
B R1 4.3 2.7   B R1 0.43 0.27  
  R2 5.2 3.2     R2 0.52 0.32  
  R3 6.2 3.9     R3 0.62 0.39  
  R4 7.6 4.7     R4 0.76 0.47  
C R1 6.9 4.3   C R1 0.70 0.44  
  R2 8.4 5.2     R2 0.84 0.52  
  R3 10.0 6.2     R3 1.00 0.62  
  R4 12.3 7.6     R4 1.23 0.76  
D R1 11.5 7.1            
  R2 13.8 8.6            
  R3 16.5 10.3            
  R4 20.2 12.6            
E* R1 18.4 11.4            
  R2 22.1 13.7            
  R3 26.5 16.5            
  R4 32.5 20.2            
F* R1 26.9 16.7            
  R2 32.4 20.1            
  R3 38.8 24.1            

R4
47.5
29.5






 

LX,OMFAH011293 -19-01MAR00-1/2


Other tires (supplied by factory):
14.9-38 3.8% faster 540/65-38 same
18.4-38 3.1% faster 600/65-38 3.1% faster
20.8-38 3.1% faster 480/70-38 same


520/70-38
3.1% faster
* Depending on equipment and legal requirements, there may in certain circumstances be only 16 reverse gears.

 

NOTE: The ground travel speeds shown in the table are theoretical. The actual speeds vary with rolling circumference, load, tire pressure, make

of tire, wheel slip etc. If the precise speed is required for specific applications, then it must be obtained by measurement.

LX,OMFAH011293 -19-01MAR00-2/2