| Light |
Diagnostic trouble code |
Description |
| yellow |
SSU 000084.09 |
Tractor speed signal not recognized |
| yellow |
SSU 000162.02 |
SSU controller, two transmission types identified |
| yellow |
SSU 000162.09 |
SSU controller, no data received from transmission controller (EPC or TCU) |
| yellow |
SSU 000168.03 |
SSU power supply (unswitched power) too high |
| yellow |
SSU 000168.04 |
SSU power supply (unswitched power) too low |
| yellow |
SSU 000177.09 |
Hydraulic oil temperature not recognized |
| yellow |
SSU 000237.31 |
Basic Control Unit (BCU) is not transmitting any data to the SSU controller |
| yellow |
SSU 000628.02 |
SSU controller, internal fault (EEPROM) |
| yellow |
SSU 000630.13 |
SSU controller not calibrated |
| blue |
SSU 000639.12 |
SSU controller, internal fault (CAN BUS) |
| blue |
SSU 000639.13 |
29-bit CAN BUS (Tractor BUS), high error rate |
| blue |
SSU 000639.19 |
29-bit CAN BUS (Tractor BUS), very high error rate |
| blue |
SSU 001079.03 |
Wheel Angle Sensor (WAS), power supply too high |
| blue |
SSU 001079.04 |
Wheel Angle Sensor (WAS), power supply too low |
| yellow |
SSU 001504.07 |
Seat switch, signal invalid |
| yellow |
SSU 001504.09 |
Seat switch, signal not received |
| yellow |
SSU 001504.14 |
No-one on operator's seat while AutoSteer is running |
| blue |
SSU 001807.02 |
Steering Input Device (SID), calibration fault |
| blue |
SSU 001807.03 |
Steering Input Device SID 1, voltage too high |
| blue |
SSU 001807.04 |
Steering Input Device SID 1, voltage too low |
| blue |
SSU 001807.05 |
Steering Input Device SID 1, current too low |
| blue |
SSU 001807.06 |
Steering Input Device SID 1, current too high |
| yellow |
SSU 001807.10 |
The signals from steering input devices SID 1 and SID 2 are unequal |
| blue |
SSU 001807.14 |
Malfunction at Steering Input Device SID 1 |
| yellow |
SSU 299433.09 |
No signal received from reverse drive lever (AutoPowr/IVT transmission) |
| yellow |
SSU 522273.00 |
Electro-hydraulic steering valve, actuation signal too low |
| yellow |
SSU 522273.01 |
Electro-hydraulic steering valve, actuation signal too high |
| yellow |
SSU 522451.00 |
Signal from the Wheel Angle Sensor (WAS) on channel 2 too high |
| yellow |
SSU 522451.01 |
Signal from the Wheel Angle Sensor (WAS) on channel 2 too low |
| yellow |
SSU 522451.14 |
Channel 1 signal from the Wheel Angle Sensor (WAS) incorrect in relation to channel 2 signal |
| yellow |
SSU 523425.09 |
No signal received from reverse drive lever |
| yellow |
SSU 523436.14 |
SSU controller, internal fault (watchdog timeout) |
| yellow |
SSU 523651.02 |
SSU controller, internal fault (stack overflow) |
| yellow |
SSU 523654.09 |
AutoTrac text display not activated |
| yellow |
SSU 523698.09 |
No signal received from GreenStar |
| yellow |
SSU 523766.02 |
Invalid entry for system activation |
| yellow |
SSU 523767.02 |
AutoTrac resume switch, fault in the engagement signal |
| yellow |
SSU 523795.02 |
Electro-hydraulic steering valve, fault during calibration |
| yellow |
SSU 523795.12 |
Error identification at electro-hydraulic steering valve |
| yellow |
SSU 523795.13 |
Electro-hydraulic steering valve, calibration error |
| yellow |
SSU 523810.01 |
Abrupt change in the SSU system voltage (ELX) |
| yellow |
SSU 523821.02 |
SSU controller, incorrect input value (tractor serial number) |
| yellow |
SSU 523824.03 |
Steering Input Device SID 2, voltage too high |
| yellow |
SSU 523824.04 |
Steering Input Device SID 2, voltage too low |
| yellow |
SSU 523824.05 |
Steering Input Device SID 2, current too low |
| yellow |
SSU 523824.06 |
Steering Input Device SID 2, current too high |
| yellow |
SSU 523824.10 |
The signals from steering input devices SID 2 and SID 1 are unequal |
| yellow |
SSU 523824.14 |
Malfunction at Steering Input Device SID 2 |
| yellow |
SSU 523826.00 |
Signal from the Wheel Angle Sensor (WAS) on channel 1 too high |
| yellow |
SSU 523826.01 |
Signal from the Wheel Angle Sensor (WAS) on channel 1 too low |
| yellow |
SSU 523826.02 |
Wheel Angle Sensor (WAS), fault during calibration |