| Light |
Diagnostic trouble code |
Description |
| blue |
SIC 000629.12 |
Controller internal fault |
| blue |
SIC 000639.12 |
Controller internal fault |
| blue |
SIC 000639.13 |
29-bit CAN BUS, high error rate |
| blue |
SIC 000639.19 |
29-bit CAN BUS, very high error rate |
| blue |
SIC 334001.09 |
Engine control unit or basic control unit has stopped sending data (engine speed) |
| blue |
SIC 334002.09 |
Basic control unit has stopped transmitting data (engine operating hours) |
| blue |
SIC 334003.09 |
Transmission control unit or BIF is/are not sending any data (hydraulic oil temperature) |
| blue |
SIC 334010.01 |
Hydraulic oil temperature too low |
| blue |
SIC 334028.14 |
Controller not calibrated |
| blue |
SIC 334041.31 |
E-ICV no.1, potentiometer at multi-function lever faulty |
| blue |
SIC 334042.31 |
E-ICV no.2, potentiometer at multi-function lever faulty |
| blue |
SIC 334043.31 |
E-ICV no.3, potentiometer at multi-function lever faulty |
| blue |
SIC 334051.14 |
E-ICV no.1, switch at multi-function lever faulty |
| blue |
SIC 334052.14 |
E-ICV no.2, switch at multi-function lever faulty |
| blue |
SIC 334053.14 |
E-ICV no.3, switch at multi-function lever faulty |
| blue |
SIC 334059.31 |
5-volt power supply is faulty |
| blue |
SIC 334060.14 |
E-ICV, transport lock switch is faulty |
| blue |
SIC 334061.14 |
E-ICV, safety switch is faulty |
| blue |
SIC 334106.12 |
Controller internal fault |
| blue |
SIC 334136.18 |
E-ICV no.1-stepper motor, supply voltage too low |
| blue |
SIC 334137.01 |
E-ICV no.1-stepper motor, supply voltage very low |
| blue |
SIC 334138.00 |
E-ICV no.1-stepper motor, supply voltage too high |
| blue |
SIC 334139.14 |
E-ICV no.1-stepper motor, no connection to controller |
| blue |
SIC 334140.14 |
E-ICV no.1-stepper motor, coil temperature too low |
| blue |
SIC 334141.14 |
E-ICV no.1-stepper motor, coil temperature too high |
| blue |
SIC 334144.18 |
E-ICV no.2-stepper motor, supply voltage too low |
| blue |
SIC 334145.01 |
E-ICV no.2-stepper motor, supply voltage very low |
| blue |
SIC 334146.00 |
E-ICV no.2-stepper motor, supply voltage too high |
| blue |
SIC 334147.14 |
E-ICV no.2-stepper motor, no connection to controller |
| blue |
SIC 334148.14 |
E-ICV no.2-stepper motor, coil temperature too low |
| blue |
SIC 334149.14 |
E-ICV no.2-stepper motor, coil temperature too high |
| blue |
SIC 334152.18 |
E-ICV no.3-stepper motor, supply voltage too low |
| blue |
SIC 334153.01 |
E-ICV no.3-stepper motor, supply voltage very low |
| blue |
SIC 334154.00 |
E-ICV no.3-stepper motor, supply voltage too high |
| blue |
SIC 334155.14 |
E-ICV no.3-stepper motor, no connection to controller |
| blue |
SIC 334156.14 |
E-ICV no.3-stepper motor, coil temperature too low |
| blue |
SIC 334157.14 |
E-ICV no.3-stepper motor, coil temperature too high |
| blue |
SIC 334201.14 |
E-ICV no.1, stepper motor does not start |
| blue |
SIC 334202.14 |
E-ICV no.2, stepper motor does not start |
| blue |
SIC 334203.14 |
E-ICV no.3, stepper motor does not start |
| blue |
SIC 334221.14 |
E-ICV no.1, stepper motor does not respond to command from controller |
| blue |
SIC 334222.14 |
E-ICV no.2, stepper motor does not respond to command from controller |
| blue |
SIC 334223.14 |
E-ICV no.3, stepper motor does not respond to command from controller |
| blue |
SIC 334240.14 |
Control unit connected to wrong harness connector |