Service (Daily / Every 10, 250 and 500 Hours)

Service procedure	Every 10 hours or daily	After the first 100 hours	Every 250 hours	Every 500 hours
Lights - Check that all lights (including headlights) are functioning properly	•
Fuel system - Drain water and sediment from fuel filter	•
Engine - Remove contaminant from area surrounding the engine	•
Cooling system/air-conditioning system - Clean the radiator and condenser, fins and screens	•
Check brakes	•
Oil level - Check the transmission/hydraulic system	•
Check the engine oil level	•
Cooling system - Check level of coolant	•
Front hitch - Lubricate cylinder and three-point hitch	•
Three-point hitch - Lubricate lift links and rockshaft	•
Front axle - Lubricate pivot bearing	•
Front-wheel drive axle - Lubricate all universal joints including u.j. shaft from transmission to front-wheel drive axle	•
Front-wheel drive axle with TLS - Lubricate hydraulic cylinder	•
Access the diagnostic trouble codes, rectify fault and then delete the diagnostic trouble codes		•
Lights - Check that all lights (including headlights) are functioning properly		•
Cab mountings - Check torques of attaching screws (see Service - Every 250 Hours)		•
Drawbar - Check torques of attaching screws (see Service - Every 250 Hours)		•
Front loader - Mounting frame, check torques of attaching screws (see Service - Every 250 Hours)		•
Front hitch - Mounting frame, check torque of attaching screws (see Service - Every 250 Hours)		•
Front PTO - Have torque of torsion damper attaching screws checked by your John Deere™ dealer.		•
Air intake hoses, check for leaks (see Service - Every 250 Hours)		•
Hydraulic system - Replace hydraulic oil filter (see Service - Every 750 Hours)		•
Transmission - Replace transmission oil filter (see Service - Every 750 Hours)		•
Front-wheel drive axle - Final drives without brake, oil change (see Service - Every 1500 Hours or 2 Years)		•
Front-wheel drive axle - axle housing, change oil (see Service - Every 1500 Hours or 2 Years).		•
Access the diagnostic trouble codes, rectify fault and then delete the diagnostic trouble codes			•
Check neutral start circuit			•
PTO actuation - Check safety circuit			•
Lights - Check settings of headlights			•
Load center - Visually inspect and clean			•
Fuel system - Drain water and sediment from fuel tank			•
Front axle without front-wheel drive - Tighten bolts			•
Wheels - Front and rear wheels, check torques of attaching screws			•
Wheels - Wheel disk to rim, check torques of attaching screws			•
Wheels - Wheel weights, check torques of attaching screws			•
Wheels - Dual wheel attachment, check torques of attaching screws (see manufacturer's specifications)			•
Cab - Cab mountings, check torque of attaching screws			•
Cab - Ground strap, check torque of attaching screws			•
Drawbar - Check torques of attaching screws			•
Front loader - Mounting frame, check torques of attaching screws			•
Front hitch - Mounting frame, check torques of attaching screws			•
Check oil level - Front wheel drive axle, axle housing			•
Check oil level - Front wheel drive axle, final drives			•
Check oil level - Front PTO			•
Air intake hoses, check for leaks			•
Foot brake, operational check			•
Park lock, operational check			•
Drawbar - Check all components for wear; check that all components function properly			•
Front axle without front-wheel drive - Lubricate the grease fittings			•
Lubricate pivoting fenders, and perform operational check			•
Rear PTO, lubricate PTO stub shaft support (with pivoting PTO stub shaft)			•
Check that all accessible ground cables are secure				•
Engine - Check drive belt for wear (rubbing)				•
Engine - Change engine oil filter				•
Engine - Change engine oil				•
Fuel system - Change fuel filter				•
Lubricate rear axle bearings				•
Change the activated carbon filter, if equipped.				•