|
1. Fill levels of the following systems were
checked and refilled if necessary:
□
1.1 Engine oil*
□
1.2 Transmission and hydraulic oil*
□
1.3 Front-wheel drive axle, oil*
□
1.4 Front PTO, oil (If equipped)*
□
1.5 Coolant
2. Screws and nuts of the following components
have been tightened to the specified torque:
□
2.1 Wheels and rims
□
2.2 Additional weights (if equipped)
□
2.3 Front PTO (If equipped)
□
2.4 Front hitch (if equipped)
□
2.5 Front loader, mounting frame (if equipped)
□
3. All grease fittings have been lubricated.
|
□
15. Transmission shifting mechanism is working properly.
16. PTOs are working properly:
□
16.1 Rear PTO
□
16.2 Front PTO (If equipped)
17. Hitches are working properly:
□
17.1 Rear hitch
□
17.2 Front hitch (if equipped)
□
18. Selective control valves are working properly.
□
19. Trailer hitches are working properly.
|
□
29. Trailer brake has been checked.
□
30. Diagnostic trouble codes have been accessed, causes rectified
and codes deleted.
□
31. Display language, units of measurement, and date have been
adjusted according to operator's needs.
□
32. On tractors with aftertreatment (Final Tier 4 / Stage IV),
activate automatic exhaust filter cleaning at the instrument panel.
□
33. Depending on tractor model, service intervals set in the
instrument panel. See “Periodic Service” in Section 210B.
|
|
□
4. Guards and shields have been checked.
□
5. Battery charge checked; battery recharged if necessary.
□
6. Operator's cab controls have all been checked (heater, blower,
windshield wiper, and windshield washer).
□
7. Observe the instructions for starting up the air-conditioning
system. See Section 210.
□
8. Operator's seat adjustable without any difficulty.
□
9. Seat belts checked.
|
□
20. Tire pressure has been checked and, if necessary, corrected.
□
21. Front axle toe-in has been checked with tractor fully ballasted;
adjust, if necessary.
□
22. Pivoting fenders have been adjusted.
□
23. Steering stops checked and adjusted. Inspection of the clearances
when the front-wheel drive axle is pivoted and steering is at the
stop. See "Prevent Front Wheel or Fender Contact with Tractor Components"
in Section 80.
□
24. Steering system is working properly.
|
□
34. With John Deere™ radio: Check whether receiver is
set to country-specific wave band (tuner band).
□
35. Attach StarFire™ receiver (if equipped).
□
36. Paint has been checked for good condition.
□
37. All warning and information stickers tested.
□
38. The SMV emblem is attached (only for North America).
|
|
□
10. Headlights have been adjusted**.
□
11. Lights are working properly.
□
12. Instrument panel gauges and indicator lights are working
properly.
□
13. Movement inhibitor is working properly.
□
14. Engine shut-off device is working properly.
|
□
25. With mechanical multi-function lever, activate dampening
function.
□
26. With electrical multi-function lever, adjustments have been
checked or calibration has been performed.
□
27. Park lock and park function of trailer air brake valve have
been checked.
□
28. Foot brakes and emergency brake have been checked.
|
39. The following systems have been checked
and are free of leaks:
□
39.1 Engine cooling system
□
39.2 Fuel system
□
39.3 Hydraulic system
□
40. All obligatory open product improvement programs must be
completed prior to delivering the machine to a customer.
□
41. A test drive has been performed.
|