Implement Codes
IMPORTANT: Use a scale to check static weight, especially with heavy implements. Static weight remaining on the front wheels with the implement lifted should always be at least 50 percent of the weight with the implement resting on the ground.
Determine the following:
- Two-wheel drive, MFWD, or Independent Link Suspension
- Front tires with or without liquid
Find implement code in John Deere implement operator's manual.
To find implement code for non-John Deere implements use the following procedure:
-
Estimate implement center of gravity (find or estimate fore-and-aft balance point)
-
Measure distance from implement hitch point to center of gravity. Record the distance (inches). Add 37 to this figure.
-
Determine the implement weight (fully loaded). Record the weight (pounds).
-
Multiply Step 2 by Step 3. Divide by 1000.
-
Resulting number is the implement code.
Use the prior information and refer to the appropriate chart to determine how many QUIK-TATCH™ weights are required.
CAUTION: Do not attempt to transport an implement without adequate
front ballast. Loss of steering control may result. With maximum front
ballast, do not attempt to transport an implement whose code exceeds:- 530 for Two-Wheel Drive
- 650 for MFWD
- 835 for 8225R, 8230, and 8330 with Independent Link Suspension
- 865 for 8430 and 8530 with Independent Link Suspension
NOTE: If no quick coupler is used, add 15 to code.
QUIK-TATCH Weights Required
|
8225R |
8225R-8320R |
8225R-8345R |
||
|---|---|---|---|---|
|
Tractor Code |
Two-Wheel Drive |
MFWD |
Independent Link Suspension |
|
|
0—320 |
0 |
— |
— |
|
|
321—335 |
S |
— |
— |
|
|
336—350 |
2 |
— |
— |
|
|
351—365 |
4 |
— |
— |
|
|
366—380 |
6 |
— |
— |
|
|
381—395 |
8 |
0 |
— |
|
|
396—410 |
10 |
S |
— |
|
|
411—425 |
12 |
2 |
— |
|
|
426—440 |
14 |
4 |
— |
|
|
441—455 |
16 |
6 |
0 |
|
|
456—470 |
18 |
8 |
S |
|
|
471—485 |
20 |
10 |
2 |
|
|
486—500 |
22 |
12 |
4 |
|
|
501—515 |
— |
14 |
6 |
|
|
516—530 |
— |
16 |
8 |
|
|
531—545 |
— |
18 |
10 |
|
|
546—560 |
— |
20 |
12 |
|
|
561—575 |
— |
22 |
14 |
|
|
576—590 |
— |
— |
16 |
|
|
591—610 |
— |
— |
18 |
|
|
611—625 |
— |
— |
20 |
|
|
626—640 |
— |
— |
22 |
|
|
641—655 |
— |
— |
— |
|
|
656—670 |
— |
— |
— |
|
|
S=Weight Support Only |
||||
|
Add to tractor code when: |
||||
|
.. Fluid is added to front inners |
15 |
60 |
60 |
|
|
.. Front duals are used |
— |
— |
60 |
|
|
.. Fluid is added to front outer duals |
— |
— |
60 |
|
|
.. Quick coupler is removed |
15 |
15 |
15 |
|
|
Maximum obtainable tractor code |
530 |
650 |
835 |
|
IMPORTANT: Tractor code must be greater than or equal to the implement code.
|
QUIK-TATCH is a trademark of Deere & Company |
OURX935,000074E-19-20081223 |