| SCV Can Controller (SCC) Diagnostic Trouble Codes |
| Diagnostic Trouble Code |
Display |
Solution |
| SCC 000158.4 |
SCC Switched Supply Voltage Low |
Selective Control Unit (SCC) switched supply voltage is below 9.0 Volts. |
| SCC 000168.4 |
SCC Switched Supply Voltage High |
Selective Control Unit (SCC) unswitched supply voltage above 18.0 V. |
| SCC 000629.12 |
SCC Control Unit Fault |
elective Control Unit (SCC) software failed to execute in allotted time. |
| SCC 000630.13 |
SCC Calibration Fault/Not Calibrated |
Selective Control Unit (SCC) valves SV-SV VII not calibrated or a failed calibration was saved. |
| SCC 000639.12 |
SCC CAN Message Overflow |
Bad intelligent device or component. SCC has not received expected messages from other components. |
| SCC 000639.14 |
SCC CAN Error Limit Exceeded |
Too many errors received by SCC Control Unit. |
| SCC 001079.3 |
SCC Sensor Supply Voltage High |
Selective Control Unit (SCC) sensor supply voltage for Option Configuration Connector above 5.25 Volts. |
| SCC 001079.4 |
SCC Sensor Supply Voltage Low |
Selective Control Unit (SCC) sensor supply voltage is below 4.55 Volts. |
| SCC 002005.9 |
ACU Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Armrest Control Unit (ACU). |
| SCC 002049.9 |
CAB Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Cab Control Unit (CAB). |
| SCC 002161.09.9 |
SV I Message Missing |
Unit (SCC) not receiving required messages from the Selective Control Valve I (SV I). |
| SCC 002162.09 |
SV II Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Selective Control Valve II (SV II). |
| SCC 002163.09 |
SV III Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Selective Control Valve III (SV III). |
| SCC 002164.09 |
SV IV Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Selective Control Valve IV (SV IV). |
| SCC 002165.09 |
SV V Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Selective Control Valve V (SV V). |
| SCC 002166.09 |
SV VI Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Selective Control Valve VI (SV VI). |
| SCC 002167.09 |
SV VII Message Missing |
Selective Control Unit (SCC) not receiving required messages from the Selective Control Valve VII (SV VII). |
| SCC 002602.18 |
Hydraulic Oil Level Low |
Hydraulic oil level low. All SCVs will respond to open loop control only. |
| SCC 521000.02 |
Front External Switch Circuit Fault |
Front Hitch External Switch failure. |
| SCC 523216.03 |
SCC Unswitched Supply Voltage High to SV I and SV II |
Unswitched supply voltage for SV I and SV II is above 18.0 Volts. |
| SCC 523216.04 |
SCC Unswitched Supply Voltage Low to SV I and SV II |
Unswitched supply voltage for SV I and SV II is below 9.0 Volts. |
| SCV Can Controller (SCC) Diagnostic Trouble Codes |
| Diagnostic Trouble Code |
Display |
Solution |
| SCC 523217.03 |
SCC Unswitched Supply Voltage High to SV VI (Front Hitch) |
Unswitched supply voltage for SV VI (Front Hitch) is above 18.0 Volts. |
| SCC 523217.04 |
SCC Unswitched Supply Voltage Low to SV VI (Front Hitch) |
Unswitched supply voltage for SV VI (Front Hitch) is below 9.0 Volts. |
| SCC 523219.03 |
SCC Unswitched Supply Voltage High to SV III and SV IV |
Unswitched supply voltage for SV III and IV is above 18.0 Volts. |
| SCC 523219.04 |
SCC Unswitched Supply Voltage Low to SV III and SV IV |
Unswitched supply voltage for SV III and IV is below 9.0 Volts. |
| SCC 523652.2 |
Wire Connector Fault |
Control unit is connected to wrong harness. |
| SCC 523693.2 |
Missing SV I Extend Control Message for 10 Seconds |
SV I external control message missing for longer than 10 seconds. |
| SCC 523693.9 |
Missing SV I Extend Control Message for 1 Seconds |
SV I external control message missing for longer than 1 second. |
| SCC 523693.19 |
Missing SV I Fault l Message Received |
SV I external control data has been received via CAN message with a failure indication. |
| SCC 523694.2 |
Missing SV II Extend Control Message for 10 Seconds |
SV II external control message missing for longer than 10 seconds. |
| SCC 523694.9 |
Missing SV II Extend Control Message for 1 Seconds |
SV II external control message missing for longer than 1 second. |
| SCC 523694.19 |
SV II External Control Fault Message Received |
SV II external control data has been received via CAN message with a failure indication. |
| SCC 523695.2 |
Missing SV I Extend Control Message for 10 Seconds |
SV I external control message missing for longer than 10 seconds. |
| SCC 523695.09 |
SV V External Control Fault Message Received |
SV V external control message missing for longer than 1 second. |
| SCC 523695.19 |
Missing SV V Extend Control Message for 1 Seconds |
SV V external control data has been received via CAN message with a failure indication. |
| SCC 523696.02 |
Missing Front Hitch External Control Message for 10 Seconds |
Front Hitch (SV VI) external control message missing for longer than 10 seconds. |
| SCC 523696.09 |
Front Hitch External Control Message Rate Fault |
Front Hitch (SV VI) external control message missing for longer than 1 seconds. |
| SCC 523696.19 |
Front Hitch External Control Fault Message Received |
Front Hitch (SV VI) external control data has been received via CAN message with a failure indication. |
| SCC 523775.19 |
Single Lever Control Hand Presence Switch Fault Message Received |
Single lever control hand presence switch failure. |