Diagnostic Trouble Code List

The diagnostic trouble codes are given in the following table:

Battery
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E001	Voltage drop while actuator is ON.	Check wires and connectors. Check battery. Check alternator. See in this section.	Press MINUS key when actuator is OFF.
E002	Battery voltage below 11.2 V.	Check wires and connectors. Check battery. Check alternator. See in this section.	Disappears when problem is resolved.
E003	Battery voltage above 16 V.	Check alternator. See in this section.	Disappears when problem is resolved.

Bale diameter potentiometer RB311
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E102	Open circuit or grounded circuit.	Check wires and connectors. Check potentiometer.	Press MINUS key when problem is resolved.
E103	Shorted circuit.	Check wires and connectors. Check potentiometer.	Press MINUS key when problem is resolved.
E104	Bale diameter below minimum.	Check potentiometer calibration. See or in this section.	Press MINUS key when problem is resolved.
E105	Bale diameter above maximum.	Check potentiometer calibration. See or in this section.	Press MINUS key when problem is resolved.

Right bale shape potentiometer RB322
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E112	Open circuit or grounded circuit.	Check wires and connectors. Check potentiometer.	Disappears after 5 seconds.
E113	Shorted circuit.	Check wires and connectors. Check potentiometer.	Disappears after 5 seconds.
E114	Right bale shape below minimum value.	Check potentiometer calibration. See or in this section.	Disappears after 5 seconds.
E115	Right bale shape above maximum value.	Check potentiometer calibration. See or in this section.	Disappears after 5 seconds.

Left bale shape potentiometer RB321
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E122	Open circuit or grounded circuit.	Check wires and connectors. Check potentiometer.	Disappears after 5 seconds.
E123	Shorted circuit.	Check wires and connectors. Check potentiometer.	Disappears after 5 seconds.
E124	Left bale shape below minimum value.	Check potentiometer calibration. See or in this section.	Disappears after 5 seconds.
E125	Left bale shape above maximum value.	Check potentiometer calibration. See or in this section.	Disappears after 5 seconds.

Twine actuator MB421
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E201	Twine actuator disconnected.	Check wires and connectors.	Press MINUS key when actuator is OFF.
E202	Twine actuator faulty or jammed.	Check twine actuator.	Press MINUS key when actuator is OFF.
E203	Resistive twine actuator power line.	Check wires and connectors. Check twine actuator.	Press MINUS key when actuator is OFF.
E204	Actuator wire short circuit to the battery.	Check wires and connectors.	Press MINUS key when problem is resolved.
E205	Actuator wire short circuit to the ground.	Check wires and connectors.	Press MINUS key when problem is resolved.

Net actuator MB411
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E211	Net actuator disconnected.	Check wires and connectors.	Press MINUS key when actuator is OFF.
E212	Net actuator faulty.	Check net actuator.	Press MINUS key when actuator is OFF.
E213	Resistive net actuator power line.	Check wires and connectors. Check net actuator.	Press MINUS key when actuator is OFF.
E214	Actuator wire short circuit to the battery.	Check wires and connectors.	Press MINUS key when problem is resolved.
E215	Actuator wire short circuit to the ground.	Check wires and connectors.	Press MINUS key when problem is resolved.

Soft core solenoid valve YB351
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E221	Soft core solenoid valve disconnected.	Check wires and connectors.	Press MINUS key when problem is resolved.
E222	Soft core solenoid valve short circuit to the ground.	Check wires and connectors. Check soft core solenoid valve.	Press MINUS key when problem is resolved.
E223	Soft core solenoid valve short circuit to the battery.	Check wires and connectors. Check soft core solenoid valve.	Press MINUS key when problem is resolved.

Pickup solenoid valve YB511
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E231	Pickup solenoid valve disconnected.	Check wires and connectors.	Press MINUS key when problem is resolved.
E232	Pickup solenoid valve short circuit to the ground.	Check wires and connectors. Check pickup solenoid valve.	Press MINUS key when problem is resolved.
E233	Pickup solenoid valve short circuit to the battery.	Check wires and connectors. Check pickup solenoid valve.	Press MINUS key when problem is resolved.

Precutter knife solenoid valve YB553
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E241	Precutter knife solenoid valve disconnected.	Check wires and connectors.	Press MINUS key when problem is resolved.
E242	Precutter knife solenoid valve short circuit to the ground.	Check wires and connectors. Check precutter knife solenoid valve.	Press MINUS key when problem is resolved.
E243	Precutter knife solenoid valve short circuit to the battery.	Check wires and connectors. Check precutter knife solenoid valve.	Press MINUS key when problem is resolved.

Drop floor solenoid valve YB533
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E251	Drop floor solenoid valve disconnected.	Check wires and connectors.	Press MINUS key when problem is resolved.
E252	Drop floor solenoid valve short circuit to the ground.	Check wires and connectors. Check drop floor solenoid valve.	Press MINUS key when problem is resolved.
E253	Drop floor solenoid valve short circuit to the battery.	Check wires and connectors. Check drop floor solenoid valve.	Press MINUS key when problem is resolved.

Cleaning auger rpm sensor SB363
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E304	Chain of cleaning auger broken.	Check cleaning auger sensor. See in Service section. Repair cleaning auger drive chain.	Press MINUS key when problem is resolved.

Baler rotation speed sensor SB362
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E311	Baler rotation speed sensor disconnected.	Check wires and connectors.	Disappears after 5 seconds.
E312	Baler rotation speed below the minimum value.	Check sensor adjustment. See in Service section. Check sensor. See in this section.	Disappears after 5 seconds.
E313	Baler rotation speed above the maximum value.	Check sensor adjustment. See in Service section. Check sensor. See in this section.	Disappears after 5 seconds.

Twine pulley sensors SB421 and SB422
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E321	Twine coil is empty or twine is not wrapped around the bale.	Replace twine coil. Check twine routing. See in Preparing the Baler section. Check adjustment of twine pulley sensors. See in Service section. Check sensors. See and in this section.	Press MINUS key when problem is resolved.
E322	Twine not cut.	Check cutter anvil adjustment. See in Service section.	Press MINUS key when problem is resolved.

Net cut switch SB412 or sensor SB414
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E401	Net cut switch or sensor always detects target (net tying rod). No net on bale.	Replace net roll. Check net routing. See in Preparing the Baler section. Check wires and connectors. Check net cut switch or sensor adjustment. See or in Service section. Check net cut switch or sensor. See or in this section.	Disappears when problem is resolved.
E402	Net cut switch or sensor never detects target (net tying rod). Net not cut.	Check net knife and counterknife position. See in Service section. Check wires and connectors. Check net cut switch or sensor adjustment. See or in Service section. Check net cut switch or sensor. See or in this section.	Disappears when problem is resolved.

Right gate latch switch SB334 or sensor SB337
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E411	Right gate latch switch or sensor never detects target. Gate always open.	Check wires and connectors. Check right gate latch switch or sensor adjustment. See , , or in Service section. Check right gate latch switch or sensor. See or in this section.	Disappears after 5 seconds.
E412	Right gate latch switch or sensor always detects target. Gate always closed.	Check wires and connectors. Check right gate latch switch or sensor adjustment. See , , or in Service section. Check right gate latch switch or sensor. See or in this section.	Disappears after 5 seconds.

Left gate latch switch SB333 or sensor SB336
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E421	Left gate latch switch or sensor never detects target. Gate always open.	Check wires and connectors. Check left gate latch switch or sensor adjustment. See or in Service section. Check left gate latch switch or sensor. See or in this section.	Disappears after 5 seconds.
E422	Left gate latch switch or sensor always detects target. Gate always closed.	Check wires and connectors. Check left gate latch switch or sensor adjustment. See or in Service section. Check left gate latch switch or sensor. See or in this section.	Disappears after 5 seconds.

Oversize bale switch SB312 or sensor SB317
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E431	Oversize bale switch or sensor never detects target.	Check wires and connectors. Check oversize switch or sensor adjustment. See , , or in Service section. Check oversize bale switch or sensor. See or in this section.	Press MINUS key when problem is resolved.
E432	Oversize bale switch or sensor always detects target.	Check wires and connectors. Check oversize switch or sensor adjustment. See , , or in Service section. Check oversize bale switch or sensor. See or in this section.	Press MINUS key when problem is resolved.

Positive analog reference
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E512	Grounded circuit.	Check potentiometer wire and connectors.	Press MINUS key when problem is resolved.
E513	Shorted circuit.	Check potentiometer wire and connectors.	Press MINUS key when problem is resolved.

EEPROM
Diagnostic trouble code	Description	Solution	How to clear the code displayed
E601	Memory faulty.	Do your personal settings again.	Disappears after 5 seconds.
E602	Memory faulty.	Check your personal settings.	Disappears after 5 seconds.
E603	Memory faulty.	See your John Deere dealer.	Disappears when problem is resolved.
E604	Memory faulty.	Check your personal settings.	Disappears after 5 seconds.
E605	Memory faulty.	See your John Deere dealer.	Disappears when problem is resolved.