Header Test Procedures

Display Address / Test Procedure Circuit Description Display / Specification RELATED FAULT CODE
1 Recall codes / Clear codes Mode Nos. 3 - 23 all
2 Global intermittent circuit mode Modes numbers 3 -23 none
3 Battery voltage to logic circuit 12.3 - 13.5 volts (normal) none
4 Battery voltage to valves 12.3 - 13.5 volts (normal) none
5 Battery voltage to valves 12,3 - 13.5 volts (normal) none
6 Sensor power (600 Series and Rigid) 4.8 - 5.2 volts 218
7 Flex pad #5 voltage (300 Series Flex) 0.0 - 5.0 volts none
8 Manual Reel, Tilt and Raise/Lower rocker switch status Code:
xxx0 - R/L Switch "OFF"
xxx1 - Slow Raise
xxx2 - Slow Lower
xxx3 - Fast Raise
xxx4 - Fast Lower
xxx5 - R/L Switch Error
xx0x - Tilt Switch Off
xx1x - Tilt Left xx2x - Tilt Right.
xx5x - Tilt Switch Error
x0xx - Reel R/L Off
x1xx - Reel Raise
x2xx - Reel Lower
x5xx - Reel R/L Error
0xxx - Reel F/A Off
1xxx - Reel Fore
2xxx - Reel Aft
5xxx - Reel F/A Error		 232, 233, 235, 236
9 Manual flex pressure increase/decrease switch status (600 Series) 0000 - Pressure "OFF"
0001 - Pressure Increase
0002 - Pressure Decrease
0005 - Switch Error		 234
10 Height control setting (Rigid) 0.50 - 4.50 volts 220
11 Float control setting (Rigid) 0.50 - 4.50 volts 221
12 Flex pad #6 voltage (300 Series Flex) 0.0 - 5.0 volts none
13 Feeder house angle sensor (Rigid) 0.25 - 4.75 volts 224
14 Left header height sensor (600 Series)
Right header height sensor (300 Series Flex)		 0.25 - 4.75 volts (600 Series)
0.0 - 5.0 volts (300 Series Flex)		 225 (600 Series)
none (300 Series Flex)
15 Right header height sensor (600 Series)
Left header height sensor (300 Series Flex)		 0.25 - 4.75 volts (600 Series)
0.0 - 5.0 volts (300 Series Flex)		 226 (600 Series)
none (300 Series Flex)

 

MB03730,000035B -19-14NOV02-1/3

Display Address / Test Procedure Circuit Description Display / Specification RELATED FAULT CODE
16 Lift cylinder pressure sensor (Rigid) 0.24 - 4.76 volts 227
17 Header height sensor # 2 0.0 - 5.0 volts none
18 Header height sensor # 3 0.0 - 5.0 volts none
19 Reel raise/lower position 0.50 - 4.50 volts 241
20 Reel fore/aft position (Not Used) 0.50 - 4.50 volts 242
21 Flex head height sensor (600 Series)
Volt sensor # 1 (300 Series Flex)		 0.25 - 4.75 volts (600 Series)
0.0 - 5.0 volts (300 Series Flex)		 240 (600 Series)
none (300 Series Flex)
22 Resume switch positions Code: 0000 - all off
0xx1 - resume float
0x1x - resume height
01xx - auto enable		 none
23 Float, tilt, height, and reel enable switch positions Code:
0000 - all "OFF"
xxx1 - reel on
xx1x - height on
x1xx - tilt on
1xxx - reel "ON"		 none
23 (Only for 300 Series) Float, tilt, height, and reel enable switch positions xx1x - Pos 1
xx2x - Pos 2
xx3x - Pos 3		 none
24 Accumulator shutoff and flex pressure diverter valve status Code:
00x0 - accum valve off
00x1 - accum valve on
000x - diverter valve off
001x - diverter valve on		 215, 216
25 Height Valve Command Code:
0000 - Valve off
0001 - Slow raise command
0002 - Slow lower command
0003 - Fast raise command
0004 - Fast lower command
- - - - - Valve disabled		 209, 210, 211, 212
26 Reel, Tilt, and Unload Valve Commands Code:
0000 - all off
xxx1 - unloading valve on
xx1x - tilt left
xx2x - tilt right
x1xx - reel raise
x2xx - reel lower
1xxx - reel fore
2xxx - reel aft		 217, 213, 214
27 Flex Pressure, Tilt and Height Operating Modes Code:
0xxx - 5xxx pressure modes
x0xx - x6xx tilt modes
xx00 - xx17 height modes		 none

 

MB03730,000035B -19-14NOV02-2/3

Display Address / Test Procedure Circuit Description Display / Specification RELATED FAULT CODE
28 Platform Type, Reel Operating Modes Code:
1xxx - middle height sensor
x1xx - mechanical height sensors
xx0x - xx7x reel f/a modes
xxx0 - xxx7 reel r/l modes		 203
29 Failure Overriding Modes Code:
0 - 4095		 none
30 Header calibration mode   none
31 Float calibration mode   none
32 Header Type 0 - flex platform with 5-pad
1 - 600 Series flex platform
2 - Rigid platform (All)
3 - Corn head		 none
33 Raise Time - Exit Cut 0.0 - 5.0 seconds (default 3) none
34 Height Set Point 0 - 250 (default 35) none
35 Height Deadband Adjustment 50 - 250 (default 105) none
36 Tilt Deadband Adjustment 50 - 250 (default 150) none
37 Flex platform fast raise 0 - fast lower/raise platform
1 - slow lower/raise platform		 none
38 Calibration error codes (600 Series)    
87 Software version xxxx - (typical: 4) none

 

MB03730,000035B -19-14NOV02-3/3