|
LC2
|
629
|
12
|
Service Alert
|
Control unit LC2 has reset itself due to watchdog timer.
|
|
LC2
|
639
|
14
|
Service Alert
|
No CAN Bus messages are arriving.
|
|
LC2
|
1231
|
12
|
Service Alert
|
Local CAN Bus message is not arriving on time or missing.
|
|
LC2
|
1510
|
03
|
Service Alert
|
Chopper vane position (cc# 824) is out of range - greater than
4.5 VDC.
|
|
LC2
|
1510
|
04
|
Service Alert
|
Chopper vane position (cc# 824) is out of range - less than
0.5 VDC.
|
|
LC2
|
1510
|
13
|
Information
|
Chopper vane position (cc# 824) requires calibration.
|
|
LC2
|
1554
|
03
|
Service Alert
|
Grain elevator speed (cc# 607) has no signal. Sensor voltage
is out of range high.
|
|
LC2
|
1554
|
04
|
Service Alert
|
Grain elevator speed (cc# 607) has no signal. Sensor voltage
is out of range low.
|
|
LC2
|
1762
|
03
|
Service Alert
|
Hydro charge pressure (cc# 707) has voltage present when the
engine is running.
|
|
LC2
|
1867
|
03
|
Service Alert
|
LPM2 micro power (cc# 202) is ON when commanded OFF by control
unit LC2.
|
|
LC2
|
1867
|
06
|
Service Alert
|
LPM2 micro power (cc# 202) is OFF when commanded ON by control
unit LC2.
|
|
LC2
|
3509
|
03
|
Service Alert
|
LC2 sensor supply 1 (cc# 273) is out of range - greater than
5.5 VDC.
|
|
LC2
|
3509
|
04
|
Service Alert
|
LC2 sensor supply 1 (cc# 273) is out of range - less than 4.5
VDC.
|
|
LC2
|
3510
|
03
|
Service Alert
|
LC2 sensor supply 2 (cc# 287) is out of range - greater than
8.5 VDC.
|
|
LC2
|
3510
|
04
|
Service Alert
|
LC2 sensor supply 2 (cc# 287) is out of range - less than 7.5
VDC.
|
|
LC2
|
3778
|
03
|
Service Alert
|
Chopper position (cc# 877) is out of range high.
|
|
LC2
|
3778
|
04
|
Service Alert
|
Chopper position (cc# 877) is out of range low.
|
|
LC2
|
3597
|
04
|
Service Alert
|
LC2 PTC power (cc# 542) is out of range - less than 4.0 VDC.
|
|
LC2
|
523319
|
03
|
Service Alert
|
LC2 12V switched power (cc# 812) is ON when commanded OFF.
|
|
LC2
|
523319
|
06
|
Service Alert
|
LC2 12V switched power (cc# 812) is OFF when commanded ON.
|
|
LC2
|
523495
|
06
|
Service Alert
|
Chopper vane angle right (cc# 333) is OFF when commanded ON
by control unit LC2.
|
|
LC2
|
523502
|
06
|
Service Alert
|
Sieve 1 close (cc# 367) is OFF when commanded ON by control
unit LC2.
|
|
LC2
|
523503
|
11
|
Service Alert
|
Chaffer close switch (cc# 384) is greater than 4 VDC for over
30 seconds.
|
|
LC2
|
523508
|
00
|
Calibration
|
Sieve tilt position (cc# 863) is valid but greater than 3.0
VDC when centered during calibration.
|
|
LC2
|
523508
|
01
|
Calibration
|
Sieve tilt position (cc# 863) is valid but less than 2.0 VDC
when centered during calibration.
|
|
LC2
|
523508
|
03
|
Service Alert
|
Sieve tilt position (cc# 863) is out of range high.
|
|
LC2
|
523508
|
04
|
Service Alert
|
Sieve tilt position (cc# 863) is out of range low.
|
|
LC2
|
523508
|
07
|
Service Alert
|
Desired sieve position not reached.
|
|
LC2
|
523508
|
16
|
Calibration
|
Sieve tilt position (cc# 863) is valid but greater than 2.0
VDC when fully right during calibration.
|
|
LC2
|
523508
|
18
|
Calibration
|
Sieve tilt position (cc# 863) is valid but less than 3.0 VDC
when fully left during calibration.
|
|
LC2
|
523509
|
00
|
Calibration
|
Chaffer tilt position (cc# 853) is valid but greater than 3.0
VDC when centered during calibration.
|
|
LC2
|
523509
|
01
|
Calibration
|
Chaffer tilt position (cc# 853) is valid but less than 2.0 VDC
when centered during calibration.
|
|
LC2
|
523509
|
03
|
Service Alert
|
Chaffer tilt position (cc# 853) is out of range high.
|
|
LC2
|
523509
|
04
|
Service Alert
|
Chaffer tilt position (cc# 853) is out of range low.
|
|
LC2
|
523509
|
09
|
Service Alert
|
Desired chaffer position not reached.
|
|
LC2
|
523509
|
13
|
Information
|
Chaffer tilt position (cc# 853) and sieve tilt position (cc#
863) require calibration.
|
|
LC2
|
523509
|
16
|
Calibration
|
Chaffer tilt position (cc# 853) is valid but greater than 2.0
VDC when fully right during calibration.
|
|
LC2
|
523509
|
18
|
Calibration
|
Chaffer tilt position (cc# 853) is valid but less than 3.0 VDC
when fully left during calibration.
|
|
LC2
|
523510
|
03
|
Service Alert
|
Chassis tilt lower solenoid (cc# 946) is ON when commanded OFF
by control unit LC2.
|
|
LC2
|
523510
|
05
|
Service Alert
|
Chassis tilt lower solenoid (cc# 946) is open circuit.
|
|
LC2
|
523510
|
06
|
Service Alert
|
Chassis tilt lower solenoid (cc# 946) is OFF when commanded
ON by control unit LC2.
|
|
LC2
|
523511
|
03
|
Service Alert
|
Right two speed four wheel drive solenoid (cc# 201) is ON when
commanded OFF by left power module 2.
|
|
LC2
|
523511
|
05
|
Service Alert
|
Right two speed four wheel drive solenoid (cc# 201) is open
circuit.
|
|
LC2
|
523511
|
06
|
Service Alert
|
Right two speed four wheel drive solenoid (cc# 201) is OFF when
commanded ON by left power module 2.
|
|
LC2
|
523512
|
03
|
Service Alert
|
Left two speed four wheel drive solenoid (cc# 204) is ON when
commanded OFF by left power module 2.
|
|
LC2
|
523512
|
05
|
Service Alert
|
Left two speed four wheel drive solenoid (cc# 204) is open circuit.
|
|
LC2
|
523512
|
06
|
Service Alert
|
Left two speed four wheel drive solenoid (cc# 204) is OFF when
commanded ON by left power module 2.
|
|
LC2
|
523515
|
06
|
Service Alert
|
Sieve 2 close (cc# 347) is OFF when commanded ON by control
unit LC2.
|
|
LC2
|
523516
|
03
|
Service Alert
|
Sieve 2 open (cc# 346) and/or sieve 2 close (cc# 347) is ON
when commanded OFF by control unit LC2.
|
|
LC2
|
523516
|
05
|
Service Alert
|
Sieve 2 open (cc# 346) and/or sieve 2 close (cc# 347) is open
circuit.
|
|
LC2
|
523516
|
06
|
Service Alert
|
Sieve 2 open (cc# 346) is OFF when commanded ON by control unit
LC2.
|
|
LC2
|
523516
|
11
|
Information
|
Right sieve actuator failed calibration. Pulses present on sieve
2 position (cc# 829). Limit switch remains on.
|
|
LC2
|
523517
|
06
|
Service Alert
|
Chaffer 2 close (cc# 377) is OFF when commanded ON by control
unit LC2.
|
|
LC2
|
523518
|
03
|
Service Alert
|
Chaffer 2 open (cc# 376) and/or chaffer 2 close (cc# 377) is
ON when commanded OFF by control unit LC2.
|
|
LC2
|
523518
|
05
|
Service Alert
|
Chaffer 2 open (cc# 376) and/or chaffer 2 close (cc# 377) is
open circuit.
|
|
LC2
|
523518
|
06
|
Service Alert
|
Chaffer 2 open (cc# 376) is OFF when commanded ON by control
unit LC2.
|
|
LC2
|
523518
|
11
|
Information
|
Right chaffer actuator failed calibration. Pulses present on
chaffer 2 position (cc# 849). Limit switch remains on.
|
|
LC2
|
523521
|
03
|
Service Alert
|
Sieve 1 open (cc# 366) and/or sieve 1 close (cc# 367) is ON
when commanded OFF by control unit LC2.
|
|
LC2
|
523521
|
05
|
Service Alert
|
Sieve 1 open (cc# 366) and/or sieve 1 close (cc# 367) is open
circuit.
|
|
LC2
|
523521
|
06
|
Service Alert
|
Sieve 1 open (cc# 366) is OFF when commanded ON by control unit
LC2.
|
|
LC2
|
523521
|
11
|
Information
|
Left sieve actuator failed calibration. Pulses present on sieve
1 position (cc# 841). Limit switch remains on.
|
|
LC2
|
523522
|
11
|
Service Alert
|
Sieve close switch (cc# 394) is greater than 4 VDC for over
30 seconds.
|
|
LC2
|
523539
|
11
|
Service Alert
|
Sieve open switch (cc# 393) is greater than 4 VDC for over 30
seconds.
|
|
LC2
|
523540
|
11
|
Service Alert
|
Chaffer open switch (cc# 383) is greater than 4 VDC for over
30 seconds.
|
|
LC2
|
523541
|
03
|
Service Alert
|
Backup alarm (cc# 903) is ON when commanded OFF by left power
module.
|
|
LC2
|
523541
|
06
|
Service Alert
|
Backup alarm (cc# 903) is OFF when commanded ON by left power
module 2.
|
|
LC2
|
523542
|
00
|
Calibration
|
Chaffer tilt position (cc# 853) is valid but greater than 3.0
VDC when centered during calibration.
|
|
LC2
|
523542
|
01
|
Calibration
|
Chaffer tilt position (cc# 853) is valid but less than 2.0 VDC
when centered during calibration.
|
|
LC2
|
523542
|
03
|
Service Alert
|
Chassis tilt position (cc# 873) is out of range high.
|
|
LC2
|
523542
|
04
|
Service Alert
|
Chassis tilt position (cc# 873) is out of range low.
|
|
LC2
|
523542
|
13
|
Information
|
Chassis tilt position (cc# 873) and sieve tilt position (cc#
863) require calibration.
|
|
LC2
|
523543
|
03
|
Service Alert
|
Chassis tilt unload solenoid (cc# 949) is ON when commanded
OFF by control unit LC2.
|
|
LC2
|
523543
|
05
|
Service Alert
|
Chassis tilt unload solenoid (cc# 949) is open circuit.
|
|
LC2
|
523543
|
06
|
Service Alert
|
Chassis tilt unload solenoid (cc# 949) is OFF when commanded
ON by control unit LC2.
|
|
LC2
|
523544
|
03
|
Service Alert
|
Chassis tilt right solenoid (cc# 948) is ON when commanded OFF
by control unit LC2.
|
|
LC2
|
523544
|
05
|
Service Alert
|
Chassis tilt right solenoid (cc# 948) is open circuit.
|
|
LC2
|
523544
|
06
|
Service Alert
|
Chassis tilt right solenoid (cc# 948) is OFF when commanded
ON by control unit LC2.
|
|
LC2
|
523545
|
03
|
Service Alert
|
Chassis tilt left solenoid (cc# 947) is ON when commanded OFF
by control unit LC2.
|
|
LC2
|
523545
|
05
|
Service Alert
|
Chassis tilt left solenoid (cc# 947) is open circuit.
|
|
LC2
|
523545
|
06
|
Service Alert
|
Chassis tilt left solenoid (cc# 947) is OFF when commanded ON
by control unit LC2.
|
|
LC2
|
523546
|
03
|
Service Alert
|
Chopper speed (cc# 617) has no signal. Sensor voltage is out
of range high.
|
|
LC2
|
523546
|
04
|
Service Alert
|
Chopper speed (cc# 617) has no signal. Sensor voltage is out
of range low.
|
|
LC2
|
523547
|
03
|
Service Alert
|
Chopper vane angle right (cc# 333) and/or chopper vane angle
left (cc# 334) is ON when commanded OFF by control unit LC2.
|
|
LC2
|
523547
|
05
|
Service Alert
|
Chopper vane angle right (cc# 333) and/or chopper vane angle
left (cc# 334) is open circuit.
|
|
LC2
|
523547
|
06
|
Service Alert
|
Chopper vane angle left (cc# 334) is OFF when commanded ON by
control unit LC2.
|
|
LC2
|
523549
|
13
|
Information
|
Sieve actuators are not calibrated.
|
|
LC2
|
523549
|
16
|
Information
|
Sieve 1 and sieve 2 actuators are not synchronized.
|
|
LC2
|
523550
|
13
|
Information
|
Chaffer actuators are not calibrated.
|
|
LC2
|
523550
|
16
|
Information
|
Chaffer 1 and chaffer 2 actuators are not synchronized.
|
|
LC2
|
523552
|
06
|
Service Alert
|
Chaffer 1 close (cc# 307) is OFF when commanded ON by control
unit LC2.
|
|
LC2
|
523561
|
11
|
Information
|
Left chaffer actuator failed calibration. Pulses present on
chaffer 1 position (cc# 809). Limit switch remains on.
|
|
LC2
|
523561
|
03
|
Service Alert
|
Chaffer 1 open (cc# 306) and/or chaffer 1 close (cc# 307) is
ON when commanded OFF by control unit LC2.
|
|
LC2
|
523561
|
05
|
Service Alert
|
Chaffer 1 open (cc# 306) and/or chaffer 1 close (cc# 307) is
open circuit.
|
|
LC2
|
523561
|
06
|
Service Alert
|
Chaffer 1 open (cc# 306) is OFF when commanded ON by control
unit LC2.
|
|
LC2
|
523565
|
03
|
Service Alert
|
Left rear marker lights (cc# 554) output is ON when commanded
OFF by control unit LC2.
|
|
LC2
|
523565
|
05
|
Service Alert
|
Left rear marker lights (cc# 554) output is open circuit.
|
|
LC2
|
523565
|
06
|
Service Alert
|
Left rear marker lights (cc# 554) output is OFF when commanded
ON by control unit LC2.
|
|
LC2
|
523611
|
03
|
Service Alert
|
Left rear discharge light (cc# 566) is ON when commanded OFF
by left power module 2.
|
|
LC2
|
523611
|
05
|
Service Alert
|
Left rear discharge light (cc# 566) is open circuit.
|
|
LC2
|
523611
|
06
|
Service Alert
|
Left rear discharge light (cc# 566) is OFF when commanded ON
by left power module 2.
|
|
LC2
|
523637
|
03
|
Service Alert
|
Four wheel drive engage solenoid (cc# 203) is ON when commanded
OFF by left power module 2.
|
|
LC2
|
523637
|
05
|
Service Alert
|
Four wheel drive engage solenoid (cc# 203) is open circuit.
|
|
LC2
|
523637
|
06
|
Service Alert
|
Four wheel drive engage solenoid (cc# 203) is OFF when commanded
ON by left power module 2.
|
|
LC2
|
523648
|
11
|
Service Alert
|
LPC2 power 4 (cc# 262) is less than 4.5 VDC at the left power
module 1 input.
|
|
LC2
|
523665
|
05
|
Service Alert
|
LC2 power 1 (cc# 252) at connector X339 is less than 4.0 VDC.
|
|
LC2
|
523666
|
05
|
Service Alert
|
LC2 power 2 (cc# 242) at connector X342 is less than 4.0 VDC.
|
|
LC2
|
523673
|
02
|
Service Alert
|
Chassis ground (cc# 010) not connected to ground.
|