Replacing or Adjusting Cutterhead Knives

Cutterhead knives need to be replaced when:

Approximately 3 mm (1/8 in.) of tungsten carbide remains on knife bottom.

Knife bolt heads become worn.

OUO6059,0001421 -19-07SEP01-1/7


causym CAUTION: Before servicing or adjusting the harvester, always:

1. Disengage all power.
2. Shut tractor engine OFF.
3. Wait until all moving parts have stopped rotating.

To adjust or replace an individual knife or row of knives, proceed as follows:

1. Turn knife sharpener crank counterclockwise a few turns to release stone from access panel (A). Remove access panel (A) and place aside.

E23503


A-Access Panel

OUO6059,0001421 -19-07SEP01-2/7


causym CAUTION: Knives are extremely sharp. Cutterhead may rotate after removing knives. Keep hands clear of sharp edges.

2. Lower stone (A) to an undisturbed knife adjacent to knife needing adjusting. Lower stone until it lightly contacts the knife.

3. Loosen three 1/2 in. mounting bolts on damaged or misaligned knife. Move stone over knife needing adjustment. Move knife until it lightly touches stone. Tighten mounting bolts finger tight. Check with stone again to see if clearance is the same as undisturbed knife. Tighten bolts to specification.

Specification

Mounting Bolts -Torque 149 N·m (110 lb-ft)
DO NOT OVERTIGHTEN.

IMPORTANT: Do not lubricate threads in the cutterhead bolts or the knife retainer bar. Proper knife holding force and tension in the bolts require the bolts and knife retainer bar to be installed with threads dry.

4. Sharpen cutterhead knives to make a true cylinder. (See SHARPENING CUTTERHEAD KNIVES in Operating the Harvester section).

5. Readjust stationary knife and recutter screen. (See ADJUSTING STATIONARY KNIFE and ADJUSTING RECUTTER SCREEN in Operating the Harvester section.)

IMPORTANT: When cutterhead diameter is increased by installing a new set of knives or adjusting the existing set, remove stationary knife and clean material packed between the stationary knife and smooth roll scraper.

If stationary knife is adjusted away from cutterhead to clear the increased diameter without cleaning, failure of adjuster linkage may occur.

TS268
E23504


A-Stone

OUO6059,0001421 -19-07SEP01-3/7


To replace entire set of knives or adjust entire set to maximum cutterhead diameter, proceed as follows:

1. Remove stationary knife. Clean out packed material between stationary knife and smooth roll scraper.

OUO6059,0001421 -19-07SEP01-4/7


2. Turn knife sharpener crank counterclockwise a few turns to release stone from access panel (A). Remove access panel (A).


A-Access Panel

E23503

OUO6059,0001421 -19-07SEP01-5/7


3. Remove spring-locking pins from gauge stops (A). Push gauge stops inside cutterhead housing and reinstall spring-locking pins to hold gauge stops in position.

4. Loosen set bolt (B). Rotate gauge bar (C) down until it rests on top of knife gauge stops (A). Tighten set bolt (B).

5. If gauge bar (C) does not contact both gauge stops (A), readjust knife gauge bar. (See ADJUSTING KNIFE SHARPENER in this section.)

causym CAUTION: Knives are extremely sharp. Cutterhead may rotate after removing knives. Keep hands clear of sharp edges.

6. Set new knives to lightly contact gauge bar (C). Tighten bolts finger tight.

7. Starting with the middle bolt, tighten to specifications.

Specification

Bolts -Torque 149 N·m (110 lb-ft)

8. Check knives again with gauge bar.

E23505


A-Gauge Stops
B-Set Bolt
C-Gauge Bar

OUO6059,0001421 -19-07SEP01-6/7


9. Return gauge bar (A) to storage position. Tighten set bolt (B).

10. Reset gauge stops (C) to inside holes. Reinstall spring-locking pins.

11. Sharpen knives to make cutterhead a true cylinder.

12. Reinstall stationary knife. (See INSTALLING STATIONARY KNIFE in this section.)

13. Readjust stationary knife and recutter screen. (See ADJUSTING STATIONARY KNIFE and ADJUSTING RECUTTER SCREEN in Operating the Harvester section.)

E23506


A-Gauge Bar
B-Set Bolt
C-Gauge Stops

OUO6059,0001421 -19-07SEP01-7/7