|
Error Code
|
Description
|
Solution
|
|
E0 01
|
Erratic supply voltage when actuator is operating
|
Check battery
Check alternator
Check wires and connections
Check actuator current draw. See Test Twine or Net Wrap Actuator
Current (Channel 018) in Service section.
|
|
E0 02
|
Low Voltage
|
Check alternator
Check wiring harness and connectors for damage.
Perform voltage test. See Test Tractor Convenience Outlet Voltage
(Channel 019) in Service section
|
|
E0 03
|
High Voltage
|
Check alternator
|
|
E1 02
|
Bale size sensor disconnected or shorted to ground
|
Check wires and connectors
Check sensor
|
|
E1 03
|
Bale size sensor shorted to power
|
Check wires and connectors
Check sensor
|
|
E1 04
|
Bale size sensor under working range
|
Calibrate the bale size display. See Calibrate Bale Diameter
Display (Channel 005) in Service section.
Perform field calibration of bale size display. See Adjust Bale
Diameter Display (Channel 028) in Operating the Baler section.
|
|
E1 05
|
Bale size sensor over working range
|
Calibrate the bale size display. See Calibrate Bale Diameter
Display (Channel 005) in Service section.
Perform field calibration of bale size display. See Adjust Bale
Diameter Display (Channel 028) in Operating the Baler section.
|
|
E1 06
|
Voltage drop
|
Check battery
Check alternator
Check wires and connections
Perform voltage test. See Test Tractor Convenience Outlet Voltage
(Channel 019) in Service section
|
|
E1 12
|
Right bale shape sensor shorted to ground
|
Check wire and connectors
Check sensor
|
|
E1 13
|
Right bale shape sensor shorted to power
|
Check wire and connectors
Check sensor
|
|
E1 14
|
Right bale shape sensor under working range
|
Check sensor adjustment. See Adjust Bale Shape Sensor (Channel
007) in Service section.
|
|
E1 15
|
Right bale shape sensor over working range
|
Check sensor adjustment. See Adjust Bale Shape Sensor (Channel
007) in Service section.
|
|
E1 16
|
Voltage drop
|
Check battery
Check alternator
Check wires and connections
|
|
E1 22
|
Left bale shape sensor shorted to ground
|
Check wire and connectors
Check sensor
|
|
E1 23
|
Left bale shape sensor shorted to power
|
Check wire and connectors
Check sensor
|
|
E1 24
|
Left bale shape sensor under working range
|
Check sensor adjustment. See Adjust Bale Shape Sensor (Channel
009) in Service section.
|
|
E1 25
|
Left bale shape sensor over working range
|
Check sensor adjustment. See Adjust Bale Shape Sensor (Channel
009) in Service section.
|
|
E1 26
|
Voltage drop
|
Check battery
Check alternator
Check wires and connections
|
|
E2 01
|
Twine actuator disconnected
|
Check wires and connectors
|
|
E2 02
|
Twine actuator faulty
|
Check actuator movement by using the extend and retract buttons
on the BaleTrak™
|
|
E2 03
|
Time out error during the twine application cycle
|
Check for obstruction or binding
|
|
E2 04
|
Twine actuator harness shorted to battery
|
Check wires and connectors
Check twine actuator
|
|
E2 05
|
Twine actuator harness shorted to ground
|
Check wires and connectors
Check twine actuator
|
|
E2 11
|
Net actuator disconnected
|
Check wires and connectors
|
|
E2 12
|
Net actuator faulty
|
Check net actuator operation using extend and retract buttons.
See Test Twine or Net Wrap Actuator Current (Channel 018) in Service
section.
|
|
E2 13
|
Time out error during the net application cycle
|
Check for obstruction or binding
|
|
E2 14
|
Net actuator harness shorted to battery
|
Check wires and connectors
Check net actuator
|
|
E2 15
|
Net actuator harness shorted to ground
|
Check wires and connectors
Check net actuator
|
|
E2 16
|
B-Wrap end of roll
|
Replace B-Wrap roll
|
|
E2 17
|
B-Wrap sensor did not detect metal tag
|
Check B-Wrap roll velcro fasteners
Check B-Wrap sensor harness and adjustment
|
|
E2 18
|
B-Wrap failure—PTO shuts off before actuator retracts
|
Ensure that the PTO is left ON until the monitor prompts it
to be shut off for proper cut location
|
|
E2 21
|
Variable core valve disconnected
|
Check wires and connectors
Check variable core valve solenoid
|
|
E2 22
|
Variable core valve shorted to power
|
Check wires and connectors
Check variable core valve solenoid
|
|
E2 23
|
Variable core valve shorted to ground
|
Check wires and connectors
Check variable core valve solenoid
|
|
E2 31
|
Pickup valve disconnected
|
Check wires and connectors
Check pickup valve solenoid
|
|
E2 32
|
Pickup valve shorts to ground
|
Check wires and connectors
Check pickup valve solenoid
|
|
E2 33
|
Pickup valve shorts to battery
|
Check wires and connectors
Check pickup valve solenoid
|
|
E2 41
|
Knives valve disconnected
|
Check wires and connectors
Check knives valve solenoid
|
|
E2 42
|
Knives valve shorts to ground
|
Check wires and connectors
Check knives valve solenoid
|
|
E2 43
|
Knives valve shorts to battery
|
Check wires and connectors
Check knives valve solenoid
|
|
E2 51
|
Drop floor valve disconnected
|
Check wires and connectors
Check drop floor valve solenoid
|
|
E2 52
|
Drop floor valve shorts to ground
|
Check wires and connectors
Check drop floor valve solenoid
|
|
E2 53
|
Drop floor valve shorts to battery
|
Check wires and connectors
Check drop floor valve solenoid
|
|
E2 55
|
Drop floor is detected down and bale size increases by 4 inches
|
Ensure that the drop floor is up while baling. Check drop floor
sensor harness and adjustment.
|
|
E3 01
|
PTO sensor open circuit
(Not used on baler with a regular pickup)
|
Check wires, connectors, and sensor for damage.
Check the PTO speed sensor readout on channel 016. See Check
PTO and Lower Drive Roll Speed (Channels 016 and 017) in Operating
the Baler section.
|
|
E3 02
|
PTO speed less than minimum speed
(Not used on baler with a regular pickup)
|
Check sensor adjustment.
Check the PTO speed sensor readout on channel 016. See Check
PTO and Lower Drive Roll Speed (Channels 016 and 017) in Operating
the Baler section.
Readout on display must be approximately 540 or 1000 rpm (depending
on speed option). Speed must not vary more than 5 rpm
|
|
E3 03
|
PTO speed exceeds maximum speed
(Not used on baler with a regular pickup)
|
Check sensor adjustment.
Check the PTO speed sensor readout on channel 016. See Check
PTO and Lower Drive Roll Speed (Channels 016 and 017) in Operating
the Baler section.
Readout on display must be approximately 540 or 1000 rpm (depending
on speed option). Speed must not vary more than 5 rpm
|
|
E3 11
|
Pickup sensor open circuit
|
Check wires, connectors, and sensor for any damage.
Check the PTO speed sensor readout on channel 017. See Check
PTO and Lower Drive Roll Speed (Channels 016 and 017) in Operating
the Baler section.
|
|
E3 12
|
Pickup speed less than the minimum speed
|
Check sensor adjustment.
Check the lower drive roll speed sensor readout on channel 017.
See Check PTO and Lower Drive Roll Speed (Channels 016 and 017) in
Operating the Baler section.
Readout on display must be approximately 310 rpm for non-precutter
and 170 rpm for precutter machines. Speed must not vary more than
5 rpm.
|
|
E3 13
|
Pickup speed exceeds the maximum speed
|
Check sensor adjustment.
Check the lower drive roll speed sensor readout on channel 017.
See Check PTO and Lower Drive Roll Speed (Channels 016 and 017) in
Operating the Baler section.
Readout on display must be approximately 310 rpm for non-precutter
and 170 rpm for precutter machines. Speed must not vary more than
5 rpm.
|
|
E4 01
|
Net did not wrap a bale
|
See Net Wrap Difficulties in the Troubleshooting section.
|
|
E4 02
|
Net did not cut
|
See Net Wrap Difficulties in the Troubleshooting section.
|
|
E4 11
|
Right gate switch is always open
|
Check right-hand gate proximity switch adjustment and function.
See Test Gate Proximity Switches (Channels 014 and 015) in Operating
the Baler section.
|
|
E4 12
|
Right gate switch is always closed
|
Check right-hand gate proximity switch adjustment and function.
See Test Gate Proximity Switches (Channels 014 and 015) in Operating
the Baler section.
|
|
E4 31
|
Oversize switch is always open
|
Check oversize bale switch adjustment and function. See Test
Oversize Bale Switch (Channel 013) in Operating the Baler section.
|
|
E4 32
|
Oversize switch is always closed
|
Check oversize bale switch adjustment and function. See Test
Oversize Bale Switch (Channel 013) in Operating the Baler section.
|
|
E5 12
|
5 V sensor supply is shorted to ground
|
Check wires and connections
|
|
E5 13
|
5 V sensor supply is shorted to power
|
Check wires and connections
|
|
E6 01
|
EEPROM Scramble—User table, both banks corrupt
|
Monitor fault. Contact your John Deere dealer or qualified service
provider.
|
|
E6 02
|
EEPROM Scramble—User table, only one bank corrupt
|
Monitor fault. Contact your John Deere dealer or qualified service
provider.
|
|
E6 03
|
EEPROM Scramble—Factory table, both banks corrupt
|
Monitor fault. Contact your John Deere dealer or qualified service
provider.
|
|
E6 04
|
EEPROM Scramble—Factory table, only one bank corrupt
|
Monitor fault. Contact your John Deere dealer or qualified service
provider.
|
|
E6 05
|
EEPROM Scramble— EEPROM device failure or software failure
|
Monitor fault. Contact your John Deere dealer or qualified service
provider.
|
|
LOnEt
|
B-Wrap end of roll
|
Replace B-wrap roll.
|