|
Error Code
|
Description
|
Solution
|
|
E0 01
|
Erratic supply voltage when actuator operating
|
Check battery
Check alternator
Check wires and connections
See Channel 019 in Service section
|
|
E0 02
|
Low Voltage
|
Check alternator
Check that wires and connections perform voltage test, see Testing
Tractor Outlet Voltage, Channel 019, in Service Section
|
|
E0 03
|
High Voltage
|
Check alternator
See Channel 019 in Service section
|
|
E1 02
|
Bale size sensor disconnected or shorted to ground
|
Check wires and connectors
Check sensor
|
|
E1 03
|
Bale size sensor shorted to power
|
Check wires and connectors
Check sensor
|
|
E1 04
|
Bale size sensor under working range
|
Check sensor adjustment, see Channel 005 in Service section
|
|
E1 05
|
Bale size sensor over working range
|
Check sensor adjustment, see Channel 005 in Service section
|
|
E1 06
|
Voltage drop
|
Check battery
Check alternator
Check wires and connections
See Channel 019 in Service section
|
|
E1 12
|
Right bale shape sensor shorted to ground
|
Check wire and connectors
Check sensor
|
|
E1 13
|
Right bale shape sensor shorted to power
|
Check wire and connectors
Check sensor
|
|
E1 14
|
Right bale shape sensor under working range
|
Check sensor adjustment, see Channel 007 in Service section
|
|
E1 15
|
Right bale shape sensor over working range
|
Check sensor adjustment, see Channel 007 in Service section
|
|
E1 16
|
Voltage drop
|
Check battery
Check alternator
Check wires and connections
See Channel 019 in Service section
|
|
E1 22
|
Left bale shape sensor shorted to ground
|
Check wire and connectors
Check sensor
|
|
E1 23
|
Left bale shape sensor shorted to power
|
Check wire and connectors
Check sensor
|
|
E1 24
|
Left bale shape sensor under working range
|
Check sensor adjustment, see Channel 009 in Service section
|
|
E1 25
|
Left bale shape sensor over working range
|
Check sensor adjustment, see Channel 009 in Service section
|
|
E1 26
|
Voltage drop
|
Check battery
Check alternator
Check wires and connections
See Channel 019 in Service section
|
|
E2 01
|
Twine actuator disconnected
|
Check wires and connectors
|
|
E2 02
|
Twine actuator faulty
|
Check actuator movement by using the extend and retract buttons
on the BaleTrak™
|
|
E2 03
|
Time out error during the twine application cycle
|
Check for obstruction or binding
|
|
E2 04
|
Twine actuator harness shorted to battery
|
Check wires and connectors
Check twine actuator
|
|
E2 05
|
Twine actuator harness shorted to ground
|
Check wires and connectors
Check twine actuator
|
|
E2 11
|
Net actuator disconnected
|
Check wires and connectors
|
|
E2 12
|
Net actuator faulty
|
Using channel 019, check that net actuator using extend or retract
buttons
|
|
E2 13
|
Time out error during the net application cycle
|
Check for obstruction or binding
|
|
E2 14
|
Net actuator harness shorted to battery
|
Check wires and connectors
Check net actuator
|
|
E2 15
|
Net actuator harness shorted to ground
|
Check wires and connectors
Check net actuator
|
|
E2 16
|
B-Wrap end of roll
|
Replace B-Wrap roll
|
|
E2 17
|
B-Wrap sensor did not detect metal tag
|
Check B-Wrap roll velcro fasteners
Check B-Wrap sensor harness and adjustment
|
|
E2 18
|
B-Wrap failure—PTO shuts off before actuator retracts
|
Ensure that the PTO is left ON until the monitor prompts it
to be shut off for proper cut location
|
|
E2 21
|
Variable core valve disconnected
|
Check wires and connectors
Check variable core valve solenoid
|
|
E2 22
|
Variable core valve shorted to power
|
Check wires and connectors
Check variable core valve solenoid
|
|
E2 23
|
Variable core valve shorted to ground
|
Check wires and connectors
Check variable core valve solenoid
|
|
E2 31
|
Pickup valve disconnected
|
Check wires and connectors
Check pickup valve solenoid
|
|
E2 32
|
Pickup valve shorts to ground
|
Check wires and connectors
Check pickup valve solenoid
|
|
E2 33
|
Pickup valve shorts to battery
|
Check wires and connectors
Check pickup valve solenoid
|
|
E2 41
|
Knives valve disconnected
|
Check wires and connectors
Check knives valve solenoid
|
|
E2 42
|
Knives valve shorts to ground
|
Check wires and connectors
Check knives valve solenoid
|
|
E2 43
|
Knives valve shorts to battery
|
Check wires and connectors
Check knives valve solenoid
|
|
E2 51
|
Drop floor valve disconnected
|
Check wires and connectors
Check drop floor valve solenoid
|
|
E2 52
|
Drop floor valve shorts to ground
|
Check wires and connectors
Check drop floor valve solenoid
|
|
E2 53
|
Drop floor valve shorts to battery
|
Check wires and connectors
Check drop floor valve solenoid
|
|
E2 55
|
Drop floor is detected down and bale size increases by 4 inches
|
Ensure that the drop floor is up while baling. Check drop floor
sensor harness and adjustment
|
|
E3 01
|
PTO sensor open circuit
(Not used on 550M Baler with a Regular pickup)
|
Check wires, connectors, and sensor for any damage.
Check the sensor readout on channel 016, See Wrap cycle without
PTO engaged
|
|
E3 02
|
PTO sensor less than minimum speed
(Not used on 550M Baler with a Regular pickup)
|
Check sensor adjustment and sensor readout, See sensor readout
on channel 016 for approximately 540 or 1000 rpm. Speed must not vary
more than 5 rpm
|
|
E3 03
|
PTO sensor exceeds maximum speed
(Not used on 550M Baler with a Regular pickup)
|
Check sensor adjustment and sensor readout, See sensor readout
on channel 016 for approximately 540 or 1000 rpm. Speed must not vary
more than 5 rpm
|
|
E3 11
|
Pickup sensor open circuit
|
Check wires, connectors, and sensor for any damage.
Check the sensor readout on channel 016, See Wrap cycle without
PTO engaged
|
|
E3 12
|
Pickup sensor exceeds the minimum speed
|
Check sensor adjustment and sensor readout. See sensor readout
on channel 017 for approximately 310 rpm for non-precutter and 170
rpm for precutter machines. Speed must not vary more than 5 rpm
|
|
E3 13
|
Pickup sensor exceeds the maximum speed
|
Check sensor adjustment and sensor readout. See sensor readout
on channel 017 for approximately 310 rpm for non-precutter and 170
rpm for precutter machines. Speed must not vary more than 5 rpm
|
|
E4 01
|
Net did not wrap a bale
|
See net section of troubleshooting
|
|
E4 02
|
Net did not cut
|
See net section of troubleshooting
|
|
E4 11
|
Right gate switch is always open
|
Check right gate switch adjustment and function. See right gate
switch adjustment and testing, channel 014 in Service section
|
|
E4 12
|
Right gate switch is always closed
|
Check right gate switch adjustment and function. See right gate
switch adjustment and testing, channel 014 in Service section
|
|
E4 31
|
Oversize switch is always open
|
Check oversize switch adjustment and function. See oversize
bale switch adjustment and testing, Channel 013 in Service section
|
|
E4 32
|
Oversize switch is always closed
|
Check oversize switch adjustment and function. See oversize
bale switch adjustment and testing, channel 013 in Service section
|
|
E5 12
|
5V sensor supply is shorted to ground
|
Check wires and connections
|
|
E5 13
|
5V sensor supply is shorted to power
|
Check wires and connections
|
|
E6 01
|
EEPROM Scramble—User table, both banks corrupt
|
Monitor fault, contact your John Deere dealer or qualified service
provider
|
|
E6 02
|
EEPROM Scramble—User table, only one bank corrupt
|
Monitor fault, contact your John Deere dealer or qualified service
provider
|
|
E6 03
|
EEPROM Scramble—Factory table, both banks corrupt
|
Monitor fault, contact your John Deere dealer or qualified service
provider
|
|
E6 04
|
EEPROM Scramble—Factory table, only one bank corrupt
|
Monitor fault, contact your John Deere dealer or qualified service
provider
|
|
E6 05
|
EEPROM Scramble— EEPROM device failure or software failure
|
Monitor fault, contact your John Deere dealer or qualified service
provider
|
|
LOnEt
|
B-Wrap end of roll
|
Replace B-wrap roll
|