GREENSTAR Display and Moisture Sensor Warning Codes

WARNING Messages and Fault Codes Displayed on GREENSTAR ™ Display

HARVEST DOC and HARVEST MONITOR Warning messages:

Messages generated by a problem controller(s) are sent to the GREENSTAR Display over the CAN Bus network.

A WARNING message is displayed on the GREENSTAR Display as a full page message. Cancelling the WARNING message by pressing the button next to the word CANCEL will cause the message to disappear.

CAUTION messages located in section "G" of the GREENSTAR Display will be displayed following the canceling of the WARNING message. When the problem is fixed or no longer exists the CAUTION message in section "G" will no longer be displayed.

HARVEST DOC and HARVEST MONITOR Internal Fault Codes:

Fault Codes can be viewed by pressing the INFO button on the GREENSTAR Display. Then pressing the button next to the entry GREENSTAR Display followed by pressing the button next to the words Recent Problems . The codes will be displayed on this page with a short description following the code. To clear these Fault Code(s), press the button next to the words Fault Codes .

GREENSTAR is a trademark of Deere & Company

OUO6075,000371B -19-22JUN04-1/5

GREENSTAR Display Warning Messages and Fault Codes

Control Unit Warning Messages / Fault Codes Description
0x80 200/20 CAN Bus Problem
The indicated device(s) are no longer communicating with the GREENSTAR Display.
Check the indicated device(s) and CAN Bus wiring.
0x80 201/21 CAN Bus Problem
Two Devices are requesting the same Run Page section.
Perform Run Page Layout to correct the conflict.
0x80 210/30 CAN Bus Problem
Too many devices are attempting to communicate with the GREENSTAR Display.
Remove 1 or more devices.
0x80 211/31 CAN Bus Problem
CAN Bus communications overload.
Reset display or turn power OFF and then back ON.
0x80 213/33 Internal Error.
A failure has been detected in the GREENSTAR Display's internal memory.
Replace GREENSTAR Display if problem persists.
0x80 220/40 Parallel Tracking Problem
Parallel tracking is not receiving data from the GPS receiver.CheckGPS receiver connectionWiring harness
0x80 221/41 Parallel Tracking Problem
The GPS Receiver is not able to acquire a differential correction signal.
0x80 224/44 Parallel Tracking Problem
No Parallel Tracking Key on KeyCard or no KeyCard present.
Install KeyCard with Parallel Tracking key in Mobile Processor.
0x80 225/45 Parallel Tracking Problem
The GPS receiver must be set to report at the 5 Hz. rate.Confirm:STARFIRE Receiver report rateLicense Level SFire2
0x80 226/46 Parallel Tracking Problem
GPS receiver has no GPS signal.
0x80 227/50 Automatic Steering Problem.
No communication with the steering controller.
0x80 230/47 Display Address Change.
You are about to change the address of the GREENSTAR Display.
Selection of the wrong address will cause loss of communication with implements.
0x80 231/52 CAN Bus Problem
Multiple primary GREENSTAR Displays detected on the bus.
Only one primary display is allowed on the bus.

 

OUO6075,000371B -19-22JUN04-2/5

Control Unit Warning Messages / Fault Codes Description
0x80 232/52 CAN Bus Problem
No primary GREENSTAR Display detected.
All systems require a primary display.
0x80 233/22 Language Selection Problem.
The following device(s) do not support the selected language.
They will continue to use the previously selected language.
0x80 234/53 CAN Bus Problem
This display is on the CCD bus.
It must be the primary address. Switch your display addresses.
0x80 235/54 CAN Bus Problem
The auto-detected CAN layer differs from the current layer selected.
Please change the selected layer.
0x80 236/55 AutoTrac Problem
The operator is responsible for the machine path.
Turn AutoTrac OFF before entering roadways.
0x80 /60 Flash Erase Failed.
GREENSTAR Display having problems erasing contour paths from memory
Replace GREENSTAR Display if problem persists.
0x80 /61 Contour Write Error -
GREENSTAR Display having problems writing contour paths to memory
Replace GREENSTAR Display if problem persists
0x80 /110 Check Wiring (CAN Bus)
Wiring problem with Harness
0x80 /111 Check Wiring (CCD)
CAN to CCD Queue Overflow
0x80 /113 Incompatible mon/cntrl.
Check for compatible controllers on CAN Bus
0x80 /120 NO GPS
GPS receiver unable to communicate with satellites
Tracking disabled
0x80 /121 No Differential GPS
The GPS Receiver is not able to acquire a differential correction signal.
Tracking disabled.
0x80 /122 WAAS in use.
Tracking inaccurate.
0x80 /123 SF1 in use.
Tracking inaccurate.
0x80 /124 GPS Updates are 1 Hz.
Tracking inaccurate.
0x80 /126 AutoTrac disabled.
Using a version of Mobile Processor Application Code that is not using secure CAN.

 

OUO6075,000371B -19-22JUN04-3/5

Moisture Sensor Warning Messages

Control Unit SPN FMI Warning Messages Description
0XD3 523107 07 1 Plunger initialization failure - Plunger could not be initialized.
Moisture disabled.
Call dealer for service.
0XD3 523107 06 2 Actuator shorted - moisture disabled.
Call dealer for service.
0XD3 523106 11 3 Relay failure - moisture disabled. Call dealer for service.
0XD3 523105 12 4 Motor failure - moisture disabled.
Call dealer for service.
0XD3 523316 18 6 Low voltage - Electronic Power (cc# 21) voltage at Moisture Sensor is too low.
Please check wiring cc# 21 and cc# 20
0XD3 523143 18 7 Low voltage - Unswitched power (cc#57) voltage at Moisture Sensor is too low. Check cc#57 and cc#10.
Data will be lost when vehicle is turned OFF.
Moisture disabled.
Call dealer for service.
0XD3 522979 18 8 Low voltage - Mass Flow Sensor power (cc# 971) voltage is too low.
Mass Flow disabled.
Call dealer for service.
0XD3 522979 16 9 High voltage - Mass Flow Sensor power (cc# 971) voltage is too high.
Mass Flow disabled.
Call dealer for service.
0XD3 523951 18 10 Low voltage - Analog voltage is too low. X volts
Moisture disabled.
Call dealer for service.
0XD3 523951 16 11 High voltage - Analog voltage is too high. X volts
Moisture disabled.
Call dealer for service.
0XD3 523116 14 12 You are about to delete a Farm Name and all Field Names and Field Totals associated with the selected Farm.
0XD3 522977 14 13 You are about to delete a Field Name and all Field Totals for the selected Field.
0XD3 523114 14 14 Moisture Curve Modify - You are about to modify a moisture curve.
0XD3 523114 13 15 Moisture Curve Invalid - The digits entered are not valid.
Check the data and try again.
0XD3 523114 31 16 Moisture Curve Conflict - Moisture disabled.
Verify Curve 1 and Curve 2 data from the Info Diagnostic page for the currently selected crop.
0XD3 523910 18 17 System is LOW on data space. Transfer data to DataStore and zero all fields and crops.
0XD3 523313 04 18 Mass Flow out of range - Mass Flow Sensor Signal (cc# 972) voltage is too low.
Mass Flow disabled.
Please check wiring CC970, CC971, and CC972. Call dealer for service.
0XD3 523313 03 19 Mass Flow out of range - Mass Flow Sensor Signal (cc# 972) voltage is too high.
Please check wiring CC970, CC971, and CC972.
Mass Flow disabled.
Call dealer for service.

 

OUO6075,000371B -19-22JUN04-4/5

Control Unit SPN FMI Warning Messages Description
0XD3 523138 14 20 Offset out of range - The calculated offset is out of range.
It must be >-10.1 and < +10.1
Offset not modified.
0XD3 523581 14 21 Mass Flow calibration is running. Cannot change crop until calibration is stopped.
0XD3 523115 14 22 You are about to clear the Crop Totals for the selected field.
0XD3 523112 14 23 You are about to clear all Crop Totals for the selected crop.
0XD3 522978 14 24 You are about to clear Field and Crop Totals.
0XD3 523113 14 25 Verify proper crop is selected.
Empty grain tank before proceeding.
0XD3 523110 14 26 Yield Estimator: Step X
Harvest at: Y mph/kph
0XD3 1869 14 28 Combine is in transport mode. Check farm, field and crop selection.
0XD3 522976 14 29 The mapping processor is not working.
0XD3 523111 14 30 You are about to clear the flash records (except the hardware records).
0XD3 190 14 31 The engine must be OFF to perform Advanced Moisture Correction. (Leave key ON).
0XD3 523105 14 32 Motor Stalled - The motor has stalled during initialization.
Clean GREENSTAR Moisture Sensor.
Moisture will be disabled until initialization is successful.
0XD3 522878 16 33 Measured temperature out of range. Call dealer for service.
0XD3 523866 14 34 Cannot change Farm, Field, Crop when recording is ON.

 

OUO6075,000371B -19-22JUN04-5/5