| Control Unit |
SPN |
FMI |
Priority |
Description |
| RCU |
126 |
12 |
Service Alert |
Five speed feeder house filter (cc# 738) problem detected when separator is not engaged. |
| RCU |
127 |
03 |
Service Alert |
Five speed feeder house pressure (cc# 737) sensor voltage is out of range - greater than 4.93 VDC. |
| RCU |
127 |
04 |
Service Alert |
Five speed feeder house pressure (cc# 737) sensor voltage is out of range - less than 0.20 VDC. |
| RCU |
127 |
12 |
Service Alert |
Five speed feeder house pressure (cc# 737) is detected when separator is not running. |
| RCU |
629 |
12 |
Service Alert |
Control unit RCU has reset itself due to watchdog timer. |
| RCU |
1075 |
03 |
Stop |
Fuel transfer pump (cc# 188) is ON when not commanded by right power module. |
| RCU |
1075 |
05 |
Service Alert |
Fuel transfer pump (cc# 188) is open circuit. |
| RCU |
1075 |
06 |
Service Alert |
Fuel transfer pump (cc# 188) is OFF when commanded ON by right power module. |
| RCU |
1231 |
09 |
Service Alert |
Message is not arriving on time or missing on local CAN Bus between the control unit RCU and right power module. |
| RCU |
1488 |
03 |
Service Alert |
Threshing speed (cc# 609) signal voltage feedback is out of range - greater than 4.90 VDC. |
| RCU |
1488 |
04 |
Service Alert |
Threshing speed (cc# 609) signal voltage feedback is out of range - less than 0.10 VDC. |
| RCU |
1489 |
03 |
Service Alert |
Cleaning fan speed (cc# 606) signal voltage feedback is out of range - greater than 4.90 VDC. |
| RCU |
1489 |
04 |
Service Alert |
Cleaning fan speed (cc# 606) signal voltage feedback is out of range - less than 0.10 VDC. |
| RCU |
1490 |
03 |
Service Alert |
Feeder house speed (cc# 619) signal voltage feedback is out of range - greater than 4.90 VDC. |
| RCU |
1490 |
04 |
Service Alert |
Feeder house speed (cc# 619) signal voltage feedback is out of range - less than 0.10 VDC. |
| RCU |
1493 |
12 |
Service Alert |
Tailings monitor system failure. Tailings sensors have read the same value for 10 seconds and are not full. |
| RCU |
1533 |
00 |
Calibration |
Feeder house tilt sensor (cc# 815) is out of range at right position - greater than 4.5 VDC. |
| RCU |
1533 |
01 |
Calibration |
Feeder house tilt sensor (cc# 815) is out of range at left position - less than 0.5 VDC. |
| RCU |
1533 |
03 |
Service Alert |
Feeder house tilt sensor (cc# 815) is out of range - greater than 4.5 VDC. |
| RCU |
1533 |
04 |
Service Alert |
Feeder house tilt sensor (cc# 815) is out of range - less than 0.5 VDC. |
| RCU |
1533 |
08 |
Calibration |
Feeder house tilt sensor (cc# 815) voltage is greater at left position than right position. |
| RCU |
1533 |
13 |
Information |
Feeder house tilt sensor (cc# 815) has not been calibrated. |
| RCU |
1533 |
16 |
Calibration |
Feeder house tilt sensor (cc# 815) voltage is greater at left position than Center position. |
| Control Unit |
SPN |
FMI |
Priority |
Description |
| RCU |
1533 |
18 |
Calibration |
Feeder house tilt sensor (cc# 815) voltage is greater at Center position than right position. |
| RCU |
1867 |
06 |
Service Alert |
RPM micro power (cc# 302) is OFF when commanded ON by Control unit RCU. |
| RCU |
3020 |
03 |
Stop |
Auger engage (cc# 319) is ON when not commanded by control unit RCU. |
| RCU |
3020 |
05 |
Service Alert |
Auger engage (cc# 319) is open circuit. |
| RCU |
3020 |
06 |
Service Alert |
Auger engage (cc# 319) is OFF when commanded ON by control unit RCU. |
| RCU |
3020 |
14 |
Service Alert |
Auger engage (cc# 319) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
3108 |
03 |
Service Alert |
Spreader speed 1 high side (cc# 343) is ON when not commanded by control unit RCU. |
| RCU |
3108 |
04 |
Service Alert |
Spreader speed 1 high side (cc# 343) is OFF when commanded ON by control unit RCU. |
| RCU |
3108 |
05 |
Service Alert |
Spreader speed 1 high side (cc# 343) is open circuit. |
| RCU |
3108 |
06 |
Service Alert |
Spreader speed 1 high side (cc# 343) is OFF when commanded ON by control unit RCU. |
| RCU |
3108 |
14 |
Service Alert |
Spreader speed 1 high side (cc# 343) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
3353 |
03 |
Service Alert |
Alternator field (cc# 007) is ON when not commanded by control unit RCU. |
| RCU |
3353 |
05 |
Service Alert |
Alternator field (cc# 007) is open circuit. |
| RCU |
3353 |
06 |
Service Alert |
Alternator field (cc# 007) is OFF when commanded ON by control unit RCU. |
| RCU |
3353 |
14 |
Service Alert |
Alternator field (cc# 007) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
3509 |
03 |
Service Alert |
RCU 5V sensor supply (cc# 293) is out of range - greater than 5.5 VDC. |
| RCU |
3509 |
04 |
Service Alert |
RCU 5V sensor supply (cc# 293) is out of range - less than 4.5 VDC. |
| RCU |
3510 |
03 |
Service Alert |
RCU 8V sensor supply (cc# 297) is out of range - greater than 8.5 VDC. |
| RCU |
3510 |
04 |
Information |
RCU 8V sensor supply (cc# 297) is out of range - less than 7.5 VDC. |
| RCU |
3597 |
06 |
Information |
RCU PTC power (cc# 562) is out of range - less than 4.0 VDC. |
| RCU |
523319 |
03 |
Service Alert |
RCU 12V switched power (cc# 822) is ON when not commanded by control unit RCU. |
| RCU |
523319 |
06 |
Service Alert |
RCU 12V switched power (cc# 822) is OFF when commanded ON by control unit RCU. |
| RCU |
523489 |
03 |
Service Alert |
Engine service lights (cc# 531) are ON when not commanded by right power module. |
| RCU |
523489 |
05 |
Service Alert |
Engine service lights (cc# 531) are open circuit. |
| RCU |
523489 |
06 |
Service Alert |
Engine service lights (cc# 531) are OFF when commanded ON by right power module. |
| RCU |
523493 |
12 |
Service Alert |
Main gearcase filter (cc# 701) problem detected when engine is not running. |
| Control Unit |
SPN |
FMI |
Priority |
Description |
| RCU |
523494 |
03 |
Service Alert |
Right row finder light (cc# 523) is ON when not commanded by control unit RCU. |
| RCU |
523494 |
05 |
Service Alert |
Right row finder light (cc# 523) is open circuit. |
| RCU |
523494 |
06 |
Service Alert |
Right row finder light (cc# 523) is OFF when commanded ON by control unit RCU. |
| RCU |
523501 |
12 |
Service Alert |
Main gearcase pressure (cc# 703) is detected when engine is not running. |
| RCU |
523574 |
03 |
Service Alert |
Main gearcase temp sensor (cc# 754) is out of range - greater than 4.93 VDC. |
| RCU |
523574 |
04 |
Service Alert |
Main gearcase temp sensor (cc# 754) is out of range - less than 0.10 VDC. |
| RCU |
523594 |
03 |
Service Alert |
Shoe service lights (cc# 595) is ON when not commanded by right power module. |
| RCU |
523594 |
05 |
Service Alert |
Shoe service lights (cc# 595) is open circuit. |
| RCU |
523594 |
06 |
Service Alert |
Shoe service lights (cc# 595) is OFF when commanded ON by right power module. |
| RCU |
523595 |
03 |
Service Alert |
Lower driving lights (cc# 586) is ON when not commanded by right power module. |
| RCU |
523595 |
05 |
Service Alert |
Lower driving lights (cc# 586) is open circuit. |
| RCU |
523595 |
06 |
Service Alert |
Lower driving lights (cc# 586) is OFF when commanded ON by right power module. |
| RCU |
523597 |
03 |
Service Alert |
Rear beacon lights (cc# 574) is ON when not commanded by right power module. |
| RCU |
523597 |
05 |
Service Alert |
Rear beacon lights (cc# 574) is open circuit. |
| RCU |
523597 |
06 |
Service Alert |
Rear beacon lights (cc# 574) is OFF when commanded ON by right power module. |
| RCU |
523598 |
06 |
Service Alert |
Cleaning fan speed decrease (cc# 326) is OFF when commanded ON by control unit RCU. |
| RCU |
523599 |
03 |
Service Alert |
Cleaning fan speed increase (cc# 325) and/or cleaning fan speed decrease (cc# 326) is ON when commanded OFF by control unit RCU. |
| RCU |
523599 |
05 |
Service Alert |
Cleaning fan speed increase (cc# 325) and/or cleaning fan speed decrease (cc# 326) is open circuit. |
| RCU |
523599 |
06 |
Service Alert |
Cleaning fan speed increase (cc# 325) is OFF when commanded ON by control unit RCU. |
| RCU |
523600 |
06 |
Service Alert |
Grain tank covers open (cc# 336) is OFF when commanded ON by control unit RCU. |
| RCU |
523601 |
03 |
Service Alert |
Grain tank covers close (cc# 335) and/or Grain tank covers open (cc# 336) is ON when commanded OFF by control unit RCU. |
| RCU |
523601 |
05 |
Service Alert |
Grain tank covers close (cc# 335) and/or Grain tank covers open (cc# 336) is open circuit. |
| RCU |
523601 |
06 |
Service Alert |
Grain tank covers close (cc# 335) is OFF when commanded ON by control unit RCU. |
| RCU |
523602 |
03 |
Service Alert |
Five speed feeder house drive valve 5 (cc# 448) is ON when not commanded by control unit RCU. |
| Control Unit |
SPN |
FMI |
Priority |
Description |
| RCU |
523602 |
04 |
Service Alert |
Five speed feeder house drive valve 5 (cc# 448) is OFF when commanded ON by control unit RCU. |
| RCU |
523602 |
05 |
Service Alert |
Five speed feeder house drive valve 5 (cc# 448) is open circuit. |
| RCU |
523602 |
06 |
Service Alert |
5 speed feeder house drive valve 5 (cc# 448) is OFF when commanded ON by control unit RCU. |
| RCU |
523603 |
03 |
Service Alert |
Five speed feeder house drive valve 4 (cc# 447) is ON when not commanded by control unit RCU. |
| RCU |
523603 |
05 |
Service Alert |
Five speed feeder house drive valve 4 (cc# 447) is open circuit. |
| RCU |
523603 |
06 |
Service Alert |
Five speed feeder house drive valve 4 (cc# 447) is OFF when commanded ON by control unit RCU. |
| RCU |
523603 |
06 |
Service Alert |
Five speed feeder house drive valve 4 (cc# 447) is OFF when commanded ON by control unit RCU. |
| RCU |
523604 |
03 |
Service Alert |
Five speed feeder house drive valve 3 (cc# 446) is ON when not commanded by control unit RCU. |
| RCU |
523604 |
04 |
Service Alert |
Five speed feeder house drive valve 3 (cc# 446) is OFF when commanded ON by control unit RCU. |
| RCU |
523604 |
05 |
Service Alert |
Five speed feeder house drive valve 3 (cc# 446) is open circuit. |
| RCU |
523604 |
06 |
Service Alert |
Five speed feeder house drive valve 3 (cc# 446) is OFF when commanded ON by control unit RCU. |
| RCU |
523605 |
03 |
Service Alert |
Five speed feeder house drive valve 2 (cc# 445) is ON when not commanded by control unit RCU. |
| RCU |
523605 |
04 |
Service Alert |
Five speed feeder house drive valve 2 (cc# 445) is OFF when commanded ON by control unit RCU. |
| RCU |
523605 |
05 |
Service Alert |
Five speed feeder house drive valve 2 (cc# 445) is open circuit. |
| RCU |
523605 |
06 |
Service Alert |
Five speed feeder house drive valve 2 (cc# 445) is OFF when commanded ON by control unit RCU. |
| RCU |
523606 |
03 |
Service Alert |
Five speed feeder house drive valve 1 (cc# 444) is ON when not commanded by control unit RCU. |
| RCU |
523606 |
04 |
Service Alert |
Five speed feeder house drive valve 1 (cc# 444) is OFF when commanded ON by control unit RCU. |
| RCU |
523606 |
05 |
Service Alert |
Five speed feeder house drive valve 1 (cc# 444) is open circuit. |
| RCU |
523606 |
06 |
Service Alert |
Five speed feeder house drive valve 1 (cc# 444) is OFF when commanded ON by control unit RCU. |
| RCU |
523611 |
03 |
Service Alert |
Right rear discharge light (cc# 565) is ON when not commanded by control unit RCU. |
| RCU |
523611 |
05 |
Service Alert |
Right rear discharge light (cc# 565) is open circuit. |
| RCU |
523611 |
06 |
Service Alert |
Right rear discharge light (cc# 565) is OFF when commanded ON by control unit RCU. |
| RCU |
523611 |
14 |
Service Alert |
Right rear discharge light (cc# 565) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
523612 |
03 |
Service Alert |
Right stubble light (cc# 563) is ON when not commanded by control unit RCU. |
| RCU |
523612 |
05 |
Service Alert |
Right stubble light (cc# 563) is open circuit. |
| RCU |
523612 |
06 |
Service Alert |
Right stubble light (cc# 563) is OFF when commanded ON by control unit RCU. |
| Control Unit |
SPN |
FMI |
Priority |
Description |
| RCU |
523612 |
14 |
Service Alert |
Right stubble light (cc# 563) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
523613 |
03 |
Service Alert |
Spreader speed 2 high side (cc# 353) is ON when not commanded by control unit RCU. |
| RCU |
523613 |
04 |
Service Alert |
Spreader speed 2 high side (cc# 353) is OFF when commanded ON by control unit RCU. |
| RCU |
523613 |
05 |
Service Alert |
Spreader speed 2 high side (cc# 353) is open circuit. |
| RCU |
523613 |
06 |
Service Alert |
Spreader speed 2 high side (cc# 353) is OFF when commanded ON by control unit RCU. |
| RCU |
523613 |
14 |
Service Alert |
Spreader speed 2 high side (cc# 353) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
523614 |
03 |
Service Alert |
Right marker lights (cc# 553) is ON when not commanded by control unit RCU. |
| RCU |
523614 |
05 |
Service Alert |
Right marker lights (cc# 553) is open circuit. |
| RCU |
523614 |
06 |
Service Alert |
Right marker lights (cc# 553) is OFF when commanded ON by control unit RCU. |
| RCU |
523614 |
14 |
Service Alert |
Right marker lights (cc# 553) output driver fault. |
| RCU |
523615 |
03 |
Stop |
Separator engage (cc# 301) is ON when not commanded by control unit RCU. |
| RCU |
523615 |
05 |
Service Alert |
Separator engage (cc# 301) is open circuit. |
| RCU |
523615 |
06 |
Service Alert |
Separator engage (cc# 301) is OFF when commanded ON by control unit RCU. |
| RCU |
523615 |
14 |
Service Alert |
Separator engage (cc# 301) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
523616 |
03 |
Service Alert |
Discharge beater speed (cc# 611) signal voltage feedback is out of range - greater than 4.90 VDC. |
| RCU |
523616 |
04 |
Service Alert |
Discharge beater speed (cc# 611) signal voltage feedback is out of range - less than 0.10 VDC. |
| RCU |
523617 |
03 |
Service Alert |
Capacitive fuel level 2 sensor (cc# 756) is out of range - greater than 4.5 VDC. |
| RCU |
523617 |
04 |
Service Alert |
Capacitive fuel level 2 sensor (cc# 756) is out of range - less than 0.2 VDC. |
| RCU |
523618 |
03 |
Service Alert |
Capacitive fuel level 1 sensor (cc# 755) is out of range - greater than 4.5 VDC. |
| RCU |
523618 |
04 |
Service Alert |
Capacitive fuel level 1 sensor (cc# 755) is out of range - less than 0.2 VDC. |
| RCU |
523619 |
03 |
Service Alert |
Resistive fuel level 2 sensor (cc# 756) is out of range - greater than 4.5 VDC. |
| RCU |
523619 |
04 |
Service Alert |
Resistive fuel level 2 sensor (cc# 756) is out of range - less than 0.2 VDC. |
| RCU |
523620 |
03 |
Service Alert |
Resistive fuel level 1 sensor (cc# 755) is out of range - greater than 4.5 VDC. |
| RCU |
523620 |
04 |
Service Alert |
Resistive fuel level 1 sensor (cc# 755) is out of range - less than 0.2 VDC. |
| RCU |
523621 |
13 |
Information |
Threshing clearance (cc# 833) has not been calibrated |
| Control Unit |
SPN |
FMI |
Priority |
Description |
| RCU |
523622 |
04 |
Information |
RPC power 5 (cc# 362) less than 10.5 VDC at the right power module input. |
| RCU |
523623 |
03 |
Service Alert |
RCU 12V switched power 2 (cc# 922) is ON when not commanded by control unit RCU. |
| RCU |
523623 |
06 |
Service Alert |
RCU 12V switched power 2 (cc# 922) is OFF when commanded ON by control unit RCU. |
| RCU |
523648 |
04 |
Information |
RPC power 4 (cc# 352) less than 10.5 VDC at the right power module input. |
| RCU |
523649 |
04 |
Information |
RPC power 3 (cc# 332) less than 10.5 VDC at the right power module input. |
| RCU |
523650 |
04 |
Information |
RPC power 2 (cc# 322) less than 10.5 VDC at the right power module input. |
| RCU |
523653 |
04 |
Information |
RPC power 1 (cc# 312) less than 10.5 VDC at the right power module input. |
| RCU |
523665 |
04 |
Information |
RCU power 1 (cc# 342) at connector X132 is less than 4.0 VDC. |
| RCU |
523666 |
04 |
Information |
RCU power 1 (cc# 342) at connector X131 is less than 4.0 VDC. |
| RCU |
523673 |
05 |
Information |
Chassis ground (cc# 010) not connected to ground. |
| RCU |
523744 |
03 |
Service Alert |
HVAC compressor (cc# 941) is ON when not commanded by control unit RCU. |
| RCU |
523744 |
05 |
Service Alert |
HVAC compressor (cc# 941) is open circuit. |
| RCU |
523744 |
06 |
Service Alert |
HVAC compressor (cc# 941) is OFF when commanded ON by control unit RCU. |
| RCU |
523744 |
14 |
Service Alert |
HVAC compressor (cc# 941) is OFF when commanded ON by control unit RCU, but there is no detected problem. |
| RCU |
523810 |
03 |
Service Alert |
Steering solenoid power (cc# 942) is ON when not commanded by control unit RCU. |
| RCU |
523810 |
06 |
Service Alert |
Steering solenoid power (cc# 942) is OFF when commanded ON by control unit RCU. |
| RCU |
524084 |
03 |
Service Alert |
Hydraulic oil temp sensor (cc# 753) is out of range - greater than 4.93 VDC. |
| RCU |
524084 |
04 |
Service Alert |
Hydraulic oil temp sensor (cc# 753) is out of range - less than 0.10 VDC. |