Diagnostic Trouble Codes - LC2 - Control Unit LC2 and Left Power Module 2

Control Unit SPN FMI Priority Description
LC2 629 12 Service Alert Control unit LC2 has reset itself due to watchdog timer.
LC2 639 14 Service Alert No CAN Bus messages are arriving.
LC2 1231 12 Service Alert Local CAN Bus message is not arriving on time or missing.
LC2 1510 03 Service Alert Chopper vane position (cc# 824) is out of range - greater than 4.5 VDC.
LC2 1510 04 Service Alert Chopper vane position (cc# 824) is out of range - less than 0.5 VDC.
LC2 1510 13 Information Chopper vane position (cc# 824) requires calibration.
LC2 1554 03 Service Alert Grain elevator speed (cc# 607) has no signal. Sensor voltage is out of range high.
LC2 1554 04 Service Alert Grain elevator speed (cc# 607) has no signal. Sensor voltage is out of range low.
LC2 1762 03 Service Alert Hydro charge pressure (cc# 707) has voltage present when the engine is running.
LC2 1867 03 Service Alert LPM2 micro power (cc# 202) is ON when commanded OFF by control unit LC2.
LC2 1867 06 Service Alert LPM2 micro power (cc# 202) is OFF when commanded ON by control unit LC2.
LC2 3509 03 Service Alert LC2 sensor supply 1 (cc# 273) is out of range - greater than 5.5 VDC.
LC2 3509 04 Service Alert LC2 sensor supply 1 (cc# 273) is out of range - less than 4.5 VDC.
LC2 3510 03 Service Alert LC2 sensor supply 2 (cc# 287) is out of range - greater than 8.5 VDC.
LC2 3510 04 Service Alert LC2 sensor supply 2 (cc# 287) is out of range - less than 7.5 VDC.
LC2 3778 03 Service Alert Chopper position (cc# 877) is out of range high.
LC2 3778 04 Service Alert Chopper position (cc# 877) is out of range low.
LC2 3597 04 Service Alert LC2 PTC power (cc# 542) is out of range - less than 4.0 VDC.
LC2 523319 03 Service Alert LC2 12V switched power (cc# 812) is ON when commanded OFF.
LC2 523319 06 Service Alert LC2 12V switched power (cc# 812) is OFF when commanded ON.
LC2 523495 06 Service Alert Chopper vane angle right (cc# 333) is OFF when commanded ON by control unit LC2.
LC2 523502 06 Service Alert Sieve 1 close (cc# 367) is OFF when commanded ON by control unit LC2.
LC2 523503 11 Service Alert Chaffer close switch (cc# 384) is greater than 4 VDC for over 30 seconds.
LC2 523508 00 Calibration Sieve tilt position (cc# 863) is valid but greater than 3.0 VDC when centered during calibration.
LC2 523508 01 Calibration Sieve tilt position (cc# 863) is valid but less than 2.0 VDC when centered during calibration.
LC2 523508 03 Service Alert Sieve tilt position (cc# 863) is out of range high.
LC2 523508 04 Service Alert Sieve tilt position (cc# 863) is out of range low.
LC2 523508 07 Service Alert Desired sieve position not reached.
LC2 523508 16 Calibration Sieve tilt position (cc# 863) is valid but greater than 2.0 VDC when fully right during calibration.

 

OUO6075,0000B3F -19-09AUG07-1/5

Control Unit SPN FMI Priority Description
LC2 523508 18 Calibration Sieve tilt position (cc# 863) is valid but less than 3.0 VDC when fully left during calibration.
LC2 523509 00 Calibration Chaffer tilt position (cc# 853) is valid but greater than 3.0 VDC when centered during calibration.
LC2 523509 01 Calibration Chaffer tilt position (cc# 853) is valid but less than 2.0 VDC when centered during calibration.
LC2 523509 03 Service Alert Chaffer tilt position (cc# 853) is out of range high.
LC2 523509 04 Service Alert Chaffer tilt position (cc# 853) is out of range low.
LC2 523509 09 Service Alert Desired chaffer position not reached.
LC2 523509 13 Information Chaffer tilt position (cc# 853) and sieve tilt position (cc# 863) require calibration.
LC2 523509 16 Calibration Chaffer tilt position (cc# 853) is valid but greater than 2.0 VDC when fully right during calibration.
LC2 523509 18 Calibration Chaffer tilt position (cc# 853) is valid but less than 3.0 VDC when fully left during calibration.
LC2 523510 03 Service Alert Chassis tilt lower solenoid (cc# 946) is ON when commanded OFF by control unit LC2.
LC2 523510 05 Service Alert Chassis tilt lower solenoid (cc# 946) is open circuit.
LC2 523510 06 Service Alert Chassis tilt lower solenoid (cc# 946) is OFF when commanded ON by control unit LC2.
LC2 523511 03 Service Alert Right two speed four wheel drive solenoid (cc# 201) is ON when commanded OFF by left power module 2.
LC2 523511 05 Service Alert Right two speed four wheel drive solenoid (cc# 201) is open circuit.
LC2 523511 06 Service Alert Right two speed four wheel drive solenoid (cc# 201) is OFF when commanded ON by left power module 2.
LC2 523512 03 Service Alert Left two speed four wheel drive solenoid (cc# 204) is ON when commanded OFF by left power module 2.
LC2 523512 05 Service Alert Left two speed four wheel drive solenoid (cc# 204) is open circuit.
LC2 523512 06 Service Alert Left two speed four wheel drive solenoid (cc# 204) is OFF when commanded ON by left power module 2.
LC2 523515 06 Service Alert Sieve 2 close (cc# 347) is OFF when commanded ON by control unit LC2.
LC2 523516 03 Service Alert Sieve 2 open (cc# 346) and/or sieve 2 close (cc# 347) is ON when commanded OFF by control unit LC2.
LC2 523516 05 Service Alert Sieve 2 open (cc# 346) and/or sieve 2 close (cc# 347) is open circuit.
LC2 523516 06 Service Alert Sieve 2 open (cc# 346) is OFF when commanded ON by control unit LC2.
LC2 523516 11 Information Right sieve actuator failed calibration. Pulses present on sieve 2 position (cc# 829). Limit switch remains on.
LC2 523517 06 Service Alert Chaffer 2 close (cc# 377) is OFF when commanded ON by control unit LC2.
LC2 523518 03 Service Alert Chaffer 2 open (cc# 376) and/or chaffer 2 close (cc# 377) is ON when commanded OFF by control unit LC2.
LC2 523518 05 Service Alert Chaffer 2 open (cc# 376) and/or chaffer 2 close (cc# 377) is open circuit.

 

OUO6075,0000B3F -19-09AUG07-2/5

Control Unit SPN FMI Priority Description
LC2 523518 06 Service Alert Chaffer 2 open (cc# 376) is OFF when commanded ON by control unit LC2.
LC2 523518 11 Information Right chaffer actuator failed calibration. Pulses present on chaffer 2 position (cc# 849). Limit switch remains on.
LC2 523521 03 Service Alert Sieve 1 open (cc# 366) and/or sieve 1 close (cc# 367) is ON when commanded OFF by control unit LC2.
LC2 523521 05 Service Alert Sieve 1 open (cc# 366) and/or sieve 1 close (cc# 367) is open circuit.
LC2 523521 06 Service Alert Sieve 1 open (cc# 366) is OFF when commanded ON by control unit LC2.
LC2 523521 11 Information Left sieve actuator failed calibration. Pulses present on sieve 1 position (cc# 841). Limit switch remains on.
LC2 523522 11 Service Alert Sieve close switch (cc# 394) is greater than 4 VDC for over 30 seconds.
LC2 523539 11 Service Alert Sieve open switch (cc# 393) is greater than 4 VDC for over 30 seconds.
LC2 523540 11 Service Alert Chaffer open switch (cc# 383) is greater than 4 VDC for over 30 seconds.
LC2 523541 03 Service Alert Backup alarm (cc# 903) is ON when commanded OFF by left power module.
LC2 523541 06 Service Alert Backup alarm (cc# 903) is OFF when commanded ON by left power module 2.
LC2 523542 00 Calibration Chaffer tilt position (cc# 853) is valid but greater than 3.0 VDC when centered during calibration.
LC2 523542 01 Calibration Chaffer tilt position (cc# 853) is valid but less than 2.0 VDC when centered during calibration.
LC2 523542 03 Service Alert Chassis tilt position (cc# 873) is out of range high.
LC2 523542 04 Service Alert Chassis tilt position (cc# 873) is out of range low.
LC2 523542 13 Information Chassis tilt position (cc# 873) and sieve tilt position (cc# 863) require calibration.
LC2 523543 03 Service Alert Chassis tilt unload solenoid (cc# 949) is ON when commanded OFF by control unit LC2.
LC2 523543 05 Service Alert Chassis tilt unload solenoid (cc# 949) is open circuit.
LC2 523543 06 Service Alert Chassis tilt unload solenoid (cc# 949) is OFF when commanded ON by control unit LC2.
LC2 523544 03 Service Alert Chassis tilt right solenoid (cc# 948) is ON when commanded OFF by control unit LC2.
LC2 523544 05 Service Alert Chassis tilt right solenoid (cc# 948) is open circuit.
LC2 523544 06 Service Alert Chassis tilt right solenoid (cc# 948) is OFF when commanded ON by control unit LC2.
LC2 523545 03 Service Alert Chassis tilt left solenoid (cc# 947) is ON when commanded OFF by control unit LC2.
LC2 523545 05 Service Alert Chassis tilt left solenoid (cc# 947) is open circuit.
LC2 523545 06 Service Alert Chassis tilt left solenoid (cc# 947) is OFF when commanded ON by control unit LC2.

 

OUO6075,0000B3F -19-09AUG07-3/5

Control Unit SPN FMI Priority Description
LC2 523546 03 Service Alert Chopper speed (cc# 617) has no signal. Sensor voltage is out of range high.
LC2 523546 04 Service Alert Chopper speed (cc# 617) has no signal. Sensor voltage is out of range low.
LC2 523547 03 Service Alert Chopper vane angle right (cc# 333) and/or chopper vane angle left (cc# 334) is ON when commanded OFF by control unit LC2.
LC2 523547 05 Service Alert Chopper vane angle right (cc# 333) and/or chopper vane angle left (cc# 334) is open circuit.
LC2 523547 06 Service Alert Chopper vane angle left (cc# 334) is OFF when commanded ON by control unit LC2.
LC2 523549 13 Information Sieve actuators are not calibrated.
LC2 523549 16 Information Sieve 1 and sieve 2 actuators are not synchronized.
LC2 523550 13 Information Chaffer actuators are not calibrated.
LC2 523550 16 Information Chaffer 1 and chaffer 2 actuators are not synchronized.
LC2 523552 06 Service Alert Chaffer 1 close (cc# 307) is OFF when commanded ON by control unit LC2.
LC2 523561 11 Information Left chaffer actuator failed calibration. Pulses present on chaffer 1 position (cc# 809). Limit switch remains on.
LC2 523561 03 Service Alert Chaffer 1 open (cc# 306) and/or chaffer 1 close (cc# 307) is ON when commanded OFF by control unit LC2.
LC2 523561 05 Service Alert Chaffer 1 open (cc# 306) and/or chaffer 1 close (cc# 307) is open circuit.
LC2 523561 06 Service Alert Chaffer 1 open (cc# 306) is OFF when commanded ON by control unit LC2.
LC2 523565 03 Service Alert Left rear marker lights (cc# 554) output is ON when commanded OFF by control unit LC2.
LC2 523565 05 Service Alert Left rear marker lights (cc# 554) output is open circuit.
LC2 523565 06 Service Alert Left rear marker lights (cc# 554) output is OFF when commanded ON by control unit LC2.
LC2 523611 03 Service Alert Left rear discharge light (cc# 566) is ON when commanded OFF by left power module 2.
LC2 523611 05 Service Alert Left rear discharge light (cc# 566) is open circuit.
LC2 523611 06 Service Alert Left rear discharge light (cc# 566) is OFF when commanded ON by left power module 2.
LC2 523637 03 Service Alert Four wheel drive engage solenoid (cc# 203) is ON when commanded OFF by left power module 2.
LC2 523637 05 Service Alert Four wheel drive engage solenoid (cc# 203) is open circuit.
LC2 523637 06 Service Alert Four wheel drive engage solenoid (cc# 203) is OFF when commanded ON by left power module 2.
LC2 523648 11 Service Alert LPC2 power 4 (cc# 262) is less than 4.5 VDC at the left power module 1 input.
LC2 523665 05 Service Alert LC2 power 1 (cc# 252) at connector X339 is less than 4.0 VDC.

 

OUO6075,0000B3F -19-09AUG07-4/5

Control Unit SPN FMI Priority Description
LC2 523666 05 Service Alert LC2 power 2 (cc# 242) at connector X342 is less than 4.0 VDC.
LC2 523673 02 Service Alert Chassis ground (cc# 010) not connected to ground.

 

OUO6075,0000B3F -19-09AUG07-5/5