Cleaning Out Machine (Annual and Specialty Crops)

CAUTION: To prevent injury, never clean machine with engine running and separator engaged. Shut OFF engine, set parking brake and remove key.

The following instructions are recommended when cleaning out machine for certified seed crops or when transporting machine inter-state.

CAUTION: Block header safely so it will not move. Lower reel safety stops.

Remove header from machine.

Drive machine over end rows or bumps to jar and shake dirt loose. Shut OFF engine, set parking brake and remove key.

Open or remove all doors and drain holes.

CAUTION: Sound horn (A) to clear everyone from area. Stay clear of machine when discharging chaff.

Start engine and let separator run until chaff stops coming out rear of machine.

Lower engine rpm to low idle and engage separator several times. Running the separator at low idle removes dirt from inside the rotor.

Move throttle to high rpm and run for a few minutes. Repeat cycle until chaff no longer comes out rear of machine.

CAUTION: Keep bystanders clear of machine when discharging chaff.

Drive machine onto blocking so right-hand side is about 150 mm (6 in.) higher, or park on incline so dirt can run out.

A-Horn

OUO6075,0000267 -19-07JAN09-1/25

CAUTION: Shut OFF engine, set parking brake, remove key, block wheels and lower feeder house safety stop.

When working with compressed air in dusty conditions, you must wear goggles and dust mask for personal protection. Air hose must have a 2 m (6 ft.) wand (end).

Start at top of machine and work down.

OUO6075,0000267 -19-07JAN09-2/25

Open cleanout doors (A), (B) and (C).

IF EQUIPPED: Release latch (D) and open cleanout door (E).

Clean grain from under grain tank cross augers over to the sump.

Clean grain from edges of unloading auger sump to the bottom. Grain must be cleaned out from doors standing on ground.

A-Cleanout Door
B-Cleanout Door
C-Cleanout Door
D-Latch
E-Cleanout Door

OUO6075,0000267 -19-07JAN09-3/25

Remove grain tank sample trough (A) and place in storage position inside grain tank.

Release clamps (B) and lower auger.

Clean top area and down into clean grain elevator to clean elevator chain. Clean all sides.

A-Sample Trough
B-Clamps

OUO6075,0000267 -19-07JAN09-4/25

Loosen clamps (A) and swing grain tank window (B) up.

Clean out area behind cab, around primary countershaft and over separator.

A-Clamps
B-Grain Tank Window

OUO6075,0000267 -19-07JAN09-5/25

IF EQUIPPED: Remove access door (A) on front side of grain tank and clean material out around multi-speed feeder house drive gearcase.

A-Access Door

OUO6075,0000267 -19-07JAN09-6/25

Clean engine compartment area. Ladder can be moved by removing quick-lock pins (A) and lifting bottom of ladder out of slot.

A-Quick-Lock Pins

OUO6075,0000267 -19-07JAN09-7/25

Raise handrail (A) and raise engine access cover (B).

A-Handrail
B-Engine Access Cover

OUO6075,0000267 -19-07JAN09-8/25

Stand on access step (A) to raise engine access covers (B) and (C).

Clean area around separator and both sides of engine.

Clean entire engine compartment area, especially under engine.

Wipe up any oil or grease found on the engine area.

A-Access Step
B-Engine Access Cover
C-Engine Access Cover

OUO6075,0000267 -19-07JAN09-9/25

Open rotary screen door (A) and clean the following areas from inside out: radiator, oil cooler, condenser (B), and rotary screen.

A-Rotary Screen Door
B-Condenser

OUO6075,0000267 -19-07JAN09-10/25

Open lower tailings elevator door (A) and clean grain elevator door (B).

Remove wing nuts (C) and remove door at upper end of tailings elevator.

Clean down sides of elevator and clean out cross auger trough.

A-Tailings Elevator Door
B-Clean Grain Elevator Door
C-Wing Nuts

OUO6075,0000267 -19-07JAN09-11/25

Clean out chaff between separator and sides of machine.

OUO6075,0000267 -19-07JAN09-12/25

Loosen nuts (A) on each side of feeder house door and push nuts towards center of feeder house.

Pull door forward to remove.

Clean feeder house through top doors (B) and (C).

Lift conveyor chain and let chain snap back several times while cleaning.

A-Nuts
B-Feeder House Door
C-Feeder House Door

OUO6075,0000267 -19-07JAN09-13/25

Lower stone trap and feed plate using handle (A). Clean areas out.

A-Handle

OUO6075,0000267 -19-07JAN09-14/25

Pull lock-out pin (A) and move handle (B) up to dump cleanout door (C) and move handle down to close and lock cleanout door.

A-Lock-Out Pin
B-Handle
C-Cleanout Door

OUO6075,0000267 -19-07JAN09-15/25

Remove quick-lock pins (A), spring latch (B) and separator covers (C). Use scraper to loosen material, and clean out through sides of machine.

A-Quick-Lock Pins
B-Spring Latch
C-Separator Covers

OUO6075,0000267 -19-07JAN09-16/25

Clean off top of axle and transmission.

OUO6075,0000267 -19-07JAN09-17/25

Open sieve and chaffer as far as possible and clean.

OUO6075,0000267 -19-07JAN09-18/25

Clean rear axle area.

OUO6075,0000267 -19-07JAN09-19/25

Remove quick lock pins (A) and turn lock (B) counterclockwise to unlock. Remove right-hand rear shield (C) and middle shield (D). Clean out fan area.

A-Quick-Lock Pins
B-Lock
C-Right-Hand Rear Shield
D-Middle Shield

OUO6075,0000267 -19-07JAN09-20/25

Remove quick-lock pins and open left-hand side shields (A) and (B) and clean area.

Turn lock (C) counterclockwise and remove shield (D).

A-Side Shields
B-Side Shields
C-Lock
D-Shield

OUO6075,0000267 -19-07JAN09-21/25

Clean area around fan.

OUO6075,0000267 -19-07JAN09-22/25

Raise chopper completely with switch (A).

A-Switch

OUO6075,0000267 -19-07JAN09-23/25

Loosen wing nut (A) and use handle (B) to disengage knifebank and clean chopper.

A-Wing Nut
B-Handle

OUO6075,0000267 -19-07JAN09-24/25

Clean chaff from spreader drive area and spreader hood.

OUO6075,0000267 -19-07JAN09-25/25