OMHXE13769: 9670 STS and 9770 STS Combines 9670 STS 735201 9770 STS 735301 , Block File: OUO6075_000083A_19

Transporting Machine on a Trailer

causym CAUTION: Avoid collisions with other roadway users. Before transporting on a public roadway check and follow local regulations regarding the use of lights, flags, over-width signs, pilot vehicles and other requirements for wide loads.

1. Empty grain tank and swing unloading auger to storage position.

2. Use folding auger switch (A) (if equipped) to fold unloading auger rearward to transport position.

3. Remove header and outside dual wheels (if equipped).

A-Folding Auger Switch

OUO6075,000083A -19-26JUN08-1/17

4. Standard Grain Tank (If Equipped):

a. Remove quick-lock pin (A) from grain tank extensions (B).

b. Fold extension to reduce overall height.

A-Quick-Lock Pins
B-Grain Tank Extensions

OUO6075,000083A -19-26JUN08-2/17

5. Standard Grain Tank (If Equipped):

a. Remove quick-lock pins (A) from grain tank corner extensions (B).

b. Fold extensions (C) to reduce overall height.

A-Quick-Lock Pins
B-Grain Tank Corner Extensions
C-Extensions

OUO6075,000083A -19-26JUN08-3/17

6. High Unload Rate Grain Tank (If Equipped):

a. Remove quick-lock pin (A) from grain tank extensions (B).

A-Quick-Lock Pins
B-Grain Tank Corner Extensions

Front Grain Tank Extension Shown

OUO6075,000083A -19-26JUN08-4/17

b. Fold front and rear grain tank extensions (A) first, then fold left-hand and right-hand grain tank extensions (B) last to reduce overall height.

A-Front and Rear Grain Tank Extensions
B-Left-Hand and Right-Hand Grain Tank Extensions

OUO6075,000083A -19-26JUN08-5/17

7. Remove grain sample trough (A) and place sample trough in storage position (B).

8. Release clamps (C) and lower auger.

9. Drive machine on trailer and put multifunction control handle in neutral.

10. Shut OFF engine, set parking brake and remove key.

11. Fold radio antenna down and retain with hook (if equipped). If hook is not available, retain antenna to cab roof with tape.

12. Swing cab ladder to the full forward position.

A-Grain Sample Trough
B-Grain Sample Trough (Storage Position)
C-Clamps

Standard Grain Tank Sample Trough Storage Position

H75363

High Unload Rate Sample Trough Storage Position

H62117

OUO6075,000083A -19-26JUN08-6/17

13. Lower and latch engine access doors (A) and lower handrail (B).

14. Tape muffler cap (C) closed to prevent damage to turbocharger.

A-Engine Access Doors
B-Handrail
C-Muffler Cap

OUO6075,000083A -19-26JUN08-7/17

causym CAUTION: Possible injury or death to you or others can occur from falling. Use a ladder or equivalent with an appropriate load rating to access location (A) when installing unloading auger retaining cap screw (B). Do not attempt to access location from engine platform.

15. Standard Grain Tank:

a. Retrieve cap screw (B), washer (C), spacer (D), and washer (E) from tool box.

b. Install hardware as shown to retain unloading auger.

A-Location
B-Cap Screw
C-Washer
D-Spacer
E-Washer

OUO6075,000083A -19-26JUN08-8/17

causym CAUTION: Possible injury or death to you or others can occur from falling. Use a ladder or equivalent with an appropriate load rating to access location (A) when installing unloading auger retaining pin (B). Do not attempt to access location from engine platform.

16. High Unload Rate Grain Tank (Optional):

a. Retrieve pin (B) and spring pin (C) from tool box.

b. Install hardware as shown to retain unloading auger.

A-Location
B-Pin
C-Spring Pin

OUO6075,000083A -19-26JUN08-9/17

17. Remove hardware (A) and remove cable (B) from storage position.

A-Hardware
B-Cable

OUO6075,000083A -19-26JUN08-10/17

18. Verify cable (A) is installed on inside of handrail (B).

A-Cable
B-Handrail

OUO6075,000083A -19-26JUN08-11/17

19. Install cable (A) and retain with spring pin (B).

A-Cable
B-Spring Pin

OUO6075,000083A -19-26JUN08-12/17

20. Wire down ladder extension and platform (A).

A-Ladder Extension and Platform

OUO6075,000083A -19-26JUN08-13/17

21. Make sure that pin (A) is installed through locking plate (B) and retained with spring pin at front corner of right-hand gull wing door and door latch (C) is fully engaged.

22. Wire down door at latch (C).

A-Pin
B-Locking Plate
C-Door Latch

OUO6075,000083A -19-26JUN08-14/17

23. Make sure pins (A) are installed through locking plates (B) and retained with spring pins at front and rear corners of left-hand gull wing doors and door latch (C) is fully engaged.

24. Wire down door at latches (C).

A-Pins
B-Locking Plate
C-Door Latches

OUO6075,000083A -19-26JUN08-15/17

25. Swing left-hand and right-hand warning light (A) rearward.

A-Warning Light

Left-Hand Warning Light Shown

OUO6075,000083A -19-26JUN08-16/17

26. Cover up slow moving vehicle emblem (A).

IMPORTANT: Fasten machine to trailer with chains.

27. Fasten machine to trailer with chains (see Machine Tie Down Location Decal located on cab ladder for tie down information).

A-Slow Moving Vehicle Emblem

OUO6075,000083A -19-26JUN08-17/17