Operate Rinse System (Rinse Solution Tank and Boom)—EU Machines Only

1. CAUTION: Spray system can contain hazardous material which can cause serious injury or death to you or others. Wear protective clothing, eyewear, and gloves. Use rinse system in an area where people, animals, vegetation and water supply etc. cannot be contaminated.

   NOTE: After solution tank has been drained, complete the following procedure nine times at a medium volume level, when using rinse system to clean solution tank and boom assembly.

   Operator must use rinse tank sight tube to determine volume of rinse water being used. Using one third of the tank volume per rinse cycle.

   It will be necessary to fill the rinse tank three times to fully complete the rinsing procedure.

   
   N106856-UN-24SEP13

   
   N99951-UN-17SEP12

   A - Solution Sump Valve

   B - Rinse Tank Sump Valve

   C - Pump On/Off Button

   D - Pump Speed Increase Button

   E - Pump Speed Decrease Button

   F - Agitation Button

   G - Bypass Valve

   Close solution tank sump valve (A).

---




2. Open rinse tank sump valve (B). Wait 13 seconds before starting pump

3. Press pump on/off button (C) on keypad.

4. Adjust pump speed, if desired, using pump speed increase button (D) and pump speed decrease button (E).

5. Press agitation button (F) to open agitation valve and rinse agitation line for 12 seconds.

6. Press agitation button again to close valve.

7. Open bypass valve (G) to rinse bypass line for eight seconds.

8. Close bypass valve.

9. 
   N106857-UN-24SEP13

   
   N98841-UN-17SEP12

   A - Tank Rinse Nozzle/Eductor Valve

   B - Eductor Rinse Valve

   C - Eductor Sump Valve

   Set eductor/tank rinse valve (A) to eductor position and rinse eductor for 12 seconds.

---




10. Open eductor rinse valve (B) to rinse eductor.

11. Open eductor sump valve (C) to rinse eductor line.

12. Close eductor rinse valve and eductor sump valve.

13. 
    N106862-UN-24SEP13

    A - Tank Rinse Nozzle/Eductor Valve

    Set tank rinse nozzle/eductor valve (A) to tank rinse position and rinse tank with rinse nozzles for six minutes.

---




14. Close rinse tank sump valve and open solution tank sump valve.

    NOTE: Opening the solution tank sump valve allows the tank walls to be washed down using rinsate solution. This conserves rinse water to ensure that enough remains to complete the rinse procedure.

15. Allow solution tank to rinse for several minutes.

16. Close solution tank sump valve and open rinse tank sump valve.

17. Finish rinsing solution tank with rinse water.

18. Set eductor/tank rinse valve to spray position.

19. Unfold boom.

20. 
    N106858-UN-24SEP13

    
    N94866-UN-21SEP11

    A - Solution Tank Sump Valve

    B - Rinse Tank Sump Valve

    C - Master Spray On Button

    D - Pump On/Off Button

    Open solution tank sump valve (A).

---




21. Close rinse tank sump valve (B).

22. CAUTION: Spray rinse solution in an area where people, animals, vegetation and water supply etc. cannot be contaminated.

    Press master spray on button (C) to spray off rise solution from solution tank.

23. When rinse solution runs out, open rinse tank sump valve.

24. Close solution tank sump valve.

25. NOTE: Chemical build-up in aspirators can occur if not cleaned out thoroughly and regularly. To clean, close all nozzles except the aspirator nozzles during boom rinse.

    Let the boom rinse with fresh clean rinse water.

26. Press pump on/off button (D) to stop pump.

27. Close rinse tank sump valve.