| |
INTERVAL |
| SERVICE |
Every Basket |
10 Hrs (Daily) |
50 Hrs |
100 Hrs |
250 Hrs |
400 Hrs |
Every Year |
600 Hrs |
Every 2 Years |
| Clean engine hood area. |
· |
|
|
|
|
|
|
|
|
| Clean side screens. |
· |
|
|
|
|
|
|
|
|
| Perform 5-step check. |
|
· |
|
|
|
|
|
|
|
| Check fuel filters for sediment. Drain or clean as necessary. |
|
· |
|
|
|
|
|
|
|
| Check engine oil and add if necessary. |
|
· |
|
|
|
|
|
|
|
| Clean lint from alternator screen. |
|
· |
|
|
|
|
|
|
|
| Check hydraulic reservoir sight glass and add as necessary. |
|
· |
|
|
|
|
|
|
|
| Clean debris from fan rotor. |
|
· |
|
|
|
|
|
|
|
| Lubricate basket cylinder and rockshaft. |
|
· |
|
|
|
|
|
|
|
| Check coolant level. |
|
· |
|
|
|
|
|
|
|
| Clean lint and dirt from cooling cores. |
|
· |
|
|
|
|
|
|
|
| Clean accumulated lint or trash from pre-cleaner fins. |
|
· |
|
|
|
|
|
|
|
| Remove lint and trash from engine compartment. |
|
· |
|
|
|
|
|
|
|
| Clean primary cab recirculating filter-If operating in dusty conditions. |
|
· |
|
|
|
|
|
|
|
| Inspect frequently for rocks, wood, or debris lodged in the stripping units or between cleaner lay down bar and upper saw drum. |
|
· |
|
|
|
|
|
|
|
| Inspect cleaner bearings for signs of over-heating or excessive looseness. Replace promptly. |
|
· |
|
|
|
|
|
|
|
| Clean cab fresh air filter and pre-cleaner-if operating in dusty conditions. |
|
· |
|
|
|
|
|
|
|
| Wipe off exterior of cab inlet air screen. |
|
· |
|
|
|
|
|
|
|
| Visually inspect tires. |
|
· |
|
|
|
|
|
|
|
| |
INTERVAL |
| SERVICE |
Every Basket |
10 Hrs |
50 Hrs |
100 Hrs |
200 Hrs |
400 Hrs |
Every Year |
Every 2 Years |
| Check final drive oil and add if necessary. |
|
|
|
· |
|
|
|
|
| Lubricate both fan bearings. |
|
|
|
· |
|
|
|
|
| Clean battery connections and check tightness of hold down brackets. |
|
|
|
· |
|
|
|
|
| Lubricate basket lid hinges. |
|
|
|
· |
|
|
|
|
| Check transmission oil level and add as necessary. |
|
|
|
· |
|
|
|
|
| Lubricate rockshaft bearings. |
|
|
|
· |
|
|
|
|
| Lubricate guide axle spindles and tie rods. |
|
|
|
· |
|
|
|
|
| Lubricate ROW-TRAK feedback cup assembly (if equipped). |
|
|
|
· |
|
|
|
|
| Lubricate cleaner doffer and saw drum bearings. |
|
|
|
· |
|
|
|
|
| Change engine oil and filter. a |
|
|
|
· |
|
|
|
|
| Change engine oil and filter. b |
|
|
|
|
· |
|
|
|
| Clean primary cab recirculating filter-Normal Conditions. |
|
|
|
|
· |
|
|
|
| Change hydraulic/hydrostatic oil and both in-line and in-tank filters. Inspect and clean in-tank screens. |
|
|
|
|
|
· |
|
|
| Drain fuel tank and clean vent. |
|
|
|
|
|
· |
|
|
| Change final drive oil (both). |
|
|
|
|
|
· |
|
|
| Change transmission oil. |
|
|
|
|
|
· |
|
|
| Check and adjust engine valve clearance. |
|
|
|
|
|
|
· |
|
| Check oil level in cleaner gearcase, add as necessary. |
|
|
|
|
|
|
· |
|
| Clean vane dump control cylinder area. |
|
|
|
|
|
|
· |
|
| Check drive belt(s) and alignment. |
|
|
|
|
|
|
· |
|
| Inspect seat belts. |
|
|
|
|
|
|
· |
|
| Add coolant conditioner. |
|
|
|
|
|
|
· |
|
| Replace primary and secondary air cleaner elements. |
|
|
|
|
|
|
· |
|
| aPerform initial oil change at 100 hours. |
| bExtend service interval by 50 percent when using PLUS-50 oil. Example: 200 Hours extends to 300 hours. |