CCU Diagnostic Codes (**)

Code 151E -"Unit 1" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 152E -"Unit 2" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 153E -"Unit 3" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 154E -"Unit 4" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 155E -"Unit 5" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 156E -"Unit 6" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 157E -"Unit 7" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 158E -"Unit 8" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 160E -"Cross auger" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 161E -"NORMAL" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 162E -"Low fuel level" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

OUO6043,00015AE -19-18DEC02-1/4

Code 163E -"Fan speed" light circuit open. Circuit is tested several times per second for an "open" or a burnt out light only when commanded to be OFF.

Code 164E -Cleaner Learn Error, Engine speed to low.

Code 165E -Cleaner Learn Error, Cleaner is OFF

Code 166E -Cleaner Fault, Top saw is slipping.

Code 167E -Cleaner Fault, Trash auger is slipping.

Code 168E -Cleaner Fault, Feeder Shaft/Doffer is slipping.

Code 169E -Open Relay Circuit, Compactor relay.

Code 170E -Operator is off of seat and not in cleaner bypass mode.

Code 171E -"Unit 1" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 172E -"Unit 2" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 173E -"Unit 3" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 174E -"Unit 4" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 175E -"Unit 5" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 176E -"Unit 6" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 177E -"Unit 7" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

OUO6043,00015AE -19-18DEC02-2/4

Code 178E -"Unit 8" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 180E -"Cross auger" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 181E -"NORMAL" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 182E -"Low fuel level" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 183E -"Fan speed" light circuit shorted. Circuit is tested several times per second for a "shorted" light only when commanded to be ON.

Code 184E -Cleaner Learn Error, Ground speed must be zero.

Code 185E -Cleaner Learn Error, "Learn" failed.

Code 186E -Units Engage Switch shorted or stuck in ON position during power-up.

Code 187E -Open relay circuit, fan clutch relay.

Code 188E -Units engage switch shorted or stuck in OFF position during power-up.

Code 189E -Open relay circuit, cleaner clutch relay.

Code 190E -Open relay circuit, units engage relay.

Code 191E -Open relay circuit, hydraulic control relay.

Code 192E -Cleaner clutch is slipping.

Code 193E -Shorted relay circuit, fan clutch relay.

Code 194E -Shorted relay circuit, compactor relay.

Code 195E -Shorted relay circuit, cleaner clutch relay.

Code 196E -Shorted relay circuit, units engage relay.

OUO6043,00015AE -19-18DEC02-3/4

Code 197E -Shorted relay circuit, hydraulic control relay.

Code 198E -Cleaner engage switch shorted or stuck in ON position during power-up.

Code 199E -Cleaner engage switch shorted or stuck in OFF position during power-up.

Code 236E -Engine speed not above 1800 RPM, operator not on seat, ground speed above 11 km/h (7 mph), or units not operating when ROW-TRAK button was pressed. It can also mean that the pressure switch is open.

Code 237E -Crop sensor or wheel sensor is out of range in learn or valve bias mode.

Code 241E -Calibration not successful.

Code 242E -Left steering solenoid driver shorted.

Code 243E -Right steering solenoid driver shorted.

Code 246E -Supply voltage is low.

Code 248E -Crop sensor signal is missing.

Code 250E -Rear wheel sensor is missing.

Code 253E -ROW-TRAK indicator light failure.

OUO6043,00015AE -19-18DEC02-4/4