Header Height Control Calibration Error Codes

NOTE: If any errors occur during calibration procedures, error codes will be displayed on tachometer.

NOTE: The condition causing the error must be corrected before calibration procedure can be continued.

Code E01 -Factory calibration must be done before header calibration.

Code E06 -Left height control setting voltage less than 0.5 V.

Code E07 -Left height control setting voltage greater than 4.5 V.

Code E08 -Left height control setting voltage noisy or going backwards.

Code E09 -Left height control setting voltage range less than 2.0 V.

Code E11 -Right height control setting voltage less than 0.5 V.

Code E12 -Right height control setting voltage greater than 4.5 V.

Code E13 -Right height control setting voltage noisy or going backwards.

Code E14 -Right height control setting voltage range less than 2.0 V.

Code E16 -Response rate setting voltage less than 0.5 V.

Code E17 -Response rate setting voltage greater than 4.5 V.

Code E18 -Response rate setting voltage noisy or going backwards.

Code E19 -Response rate setting voltage range less than 2.0 V.

Code E21 -Left raise valve deadband not consistent within 30 mA.

Code E22 -Left raise valve deadband not found.

Code E23 -Left raise valve deadband greater than 450 mA.

Code E24 -Left raise valve deadband less than 200 mA.

Code E26 -Left lower valve deadband not consistent within 30 mA.

Code E27 -Left lower raise valve deadband not found.

Code E28 -Left lower valve deadband greater than 450 mA.

Code E29 -Left lower valve deadband less than 200 mA.

Code E31 -Right raise valve deadband not consistent within 30 mA.

Code E32 -Right raise valve deadband not found.

Code E33 -Right raise valve deadband greater than 450 mA.

Code E34 -Right raise valve deadband less than 200 mA.

Code E36 -Right lower valve deadband not consistent within 30 mA.

Code E37 -Right lower raise valve deadband not found.

Code E38 -Right lower valve deadband greater than 450 mA.

Code E39 -Right lower valve deadband less than 200 mA.

NXD8,M997620,C2 -19-25FEB98-1/3

Code E41 -Left outer #1 height sensor voltage less than 0.5 V.

Code E42 -Left outer #1 height sensor voltage greater than 4.5 V.

Code E43 -Left outer #1 height sensor voltage noisy or going backwards.

Code E44 -Left outer #1 height sensor voltage range less than 2.0 V.

Code E45 -Left outer #1 height sensor lower voltage greater than 2.5 V.

Code E46 -Left outer #1 height sensor upper voltage less than 2.5 V.

Code E51 -Left outer #2 height sensor voltage less than 0.5 V.

Code E52 -Left outer #2 height sensor voltage greater than 4.5 V.

Code E53 -Left outer #2 height sensor voltage noisy or going backwards.

Code E54 -Left outer #2 height sensor voltage range less than 2.0 V.

Code E55 -Left outer #2 height sensor lower voltage greater than 2.5 V.

Code E56 -Left outer #2 height sensor upper voltage less than 2.5 V.

Code E61 -Left inner height sensor voltage less than 0.5 V.

Code E62 -Left inner height sensor voltage greater than 4.5 V.

Code E63 -Left inner height sensor voltage noisy or going backwards.

Code E64 -Left inner height sensor voltage range less than 2.0 V.

Code E65 -Left inner height sensor lower voltage greater than 2.5 V.

Code E66 -Left inner height sensor upper voltage less than 2.5 V.

Code E71 -Right outer #1 height sensor voltage less than 0.5 V.

Code E72 -Right outer #1 height sensor voltage greater than 4.5 V.

Code E73 -Right outer #1 height sensor voltage noisy or going backwards.

Code E74 -Right outer #1 height sensor voltage range less than 2.0 V.

Code E75 -Right outer #1 height sensor lower voltage greater than 2.5 V.

Code E76 -Right outer #1 height sensor upper voltage less than 2.5 V.

Code E81 -Right outer #2 height sensor voltage less than 0.5 V.

Code E82 -Right outer #2 height sensor voltage greater than 4.5 V.

Code E83 -Right outer #2 height sensor voltage noisy or going backwards.

Code E84 -Right outer #2 height sensor voltage range less than 2.0 V.

Code E85 -Right outer #2 height sensor lower voltage greater than 2.5 V.

Code E86 -Right outer #2 height sensor upper voltage less than 2.5 V.

Code E91 -Right inner height sensor voltage less than 0.5 V.

Code E92 -Right inner height sensor voltage greater than 4.5 V.

NXD8,M997620,C2 -19-25FEB98-2/3

Code E93 -Right inner height sensor voltage noisy or going backwards.

Code E94 -Right inner height sensor voltage range less than 2.0 V.

Code E95 -Right inner height sensor lower voltage greater than 2.5 V.

Code E96 -Right inner height sensor upper voltage less than 2.5 V.

NXD8,M997620,C2 -19-25FEB98-3/3