OMN405620

Symptom	Problem	Solution
Inner boom section does not fold out.	Faulty switch.	Replace switch.
	Load sense jamming valve not working.	See your John Deere dealer.
	Damaged or corroded electrical connections.	Repair, replace, or clean electrical connection.
	Failed solenoid coil or relay.	Replace coil or relay.
	Sticking hydraulic spool.	Remove hydraulic spool and clean or (See your John Deere dealer.)
	Check valve stuck shut in load sense line.	Remove and clean check valve or (See your John Deere dealer.)
	Plugged orifice or hydraulic line.	Remove and clean orifice or hydraulic line.
	Faulty inner boom fold cylinder.	See your John Deere dealer.

Outer boom section does not fold out.	Faulty switch.	Replace switch.
	Load sense jamming valve not working.	See your John Deere dealer.
	Damaged or corroded electrical connections.	Repair, replace, or clean electrical connection.
	Failed solenoid coil or relay.	Replace coil or relay.
	Sticking hydraulic spool.	Remove hydraulic spool and clean or (See your John Deere dealer.)
	Check valve stuck shut in load sense line.	Remove and clean check valve or (See your John Deere dealer.)
	Plugged orifice or hydraulic line.	Remove and clean orifice or hydraulic line.
	Faulty inner boom cylinder switch.	See your John Deere dealer.
	Faulty outer boom fold cylinder.	See you John Deere dealer.

Outer boom section folds out part way and stops.

Hydraulic cylinder magnetic switch releases.

Fold boom and retry unfolding procedure.

Inner boom section does not fold in.	Faulty switch.	Replace switch.
	Load sense jamming valve not working.	See your John Deere dealer.
	Damaged or corroded electrical connections.	Repair, replace, or clean electrical connection.
	Failed solenoid coil or relay.	Replace coil or relay.
	Sticking hydraulic spool.	Remove hydraulic spool and clean or (See your John Deere dealer.)
	Check valve stuck shut in load sense line.	Remove and clean check valve or (See your John Deere dealer.)
	Plugged orifice or hydraulic line.	Remove and clean orifice or hydraulic line.
	Faulty outer boom cylinder switch.	See your John Deere dealer.
	Faulty inner boom fold cylinder.	See your John Deere dealer.

Inner boom section folds in part way and stops.

Hydraulic cylinder magnetic switch releases.

Unfold boom and retry folding procedure.

Outer boom section does not fold in or inner boom folds in before outer boom folds in.	Faulty switch.	Replace switch.
	Load sense jamming valve not working.	See your John Deere dealer.
	Damaged or corroded electrical connections.	Repair, replace, or clean electrical connections.
	Failed solenoid coil or relay.	Replace coil or relay.
	Sticking hydraulic spool.	Remove hydraulic spool and clean or (See your John Deere dealer.)
	Check valve stuck shut in load sense line.	Remove and clean check valve or (See your John Deere dealer.)
	Plugged orifice or hydraulic line.	Remove and clean orifice or hydraulic line.
	Faulty outer boom fold cylinder.	See your John Deere dealer.

Boom will not return to level after rolling in either direction or boom does not roll freely.

Suspended center frame binds at wear plates or center mounting bearings too far forward on shaft.

See your John Deere dealer.

Boom does not raise or lower.	Faulty switch.	Replace switch.
	Load sense jamming valve not working.	See your John Deere dealer.
	Damaged or corroded electrical connections.	Repair, replace, or clean electrical connection.
	Failed solenoid coil or relay.	Replace coil or relay.
	Sticking hydraulic spool.	Remove hydraulic spool and clean or (see your John Deere dealer.)
	Check valve stuck shut in load sense line.	Remove and clean check valve or (see your John Deere dealer.)
	Faulty lift cylinders.	See your John Deere dealer.
	Hydraulic compensator pressure not to specification.	See your John Deere dealer.

Boom lift raises too fast.

Orifice in hydraulic line is missing.

Install correct size orifice.

One individual boom function does not stop when switch is released or is slow to release.	Sticking or faulty switch.	Repair or replace switch.
	Sticking hydraulic spool assembly.	Clean spool assembly or (see your John Deere dealer.)
	Faulty solenoid valve.	Repair or replace solenoid valve.
	Load sense jamming valve not working.	See your John Deere dealer.

OUO6092,000032D-19-20100520