Attach the Bucket or Attachment

500-Style Carrier

1. The attaching procedure is the same for all attachments, bucket attachment shown.

   
   W22953-UN-29AUG12

   A - Hook (1 each side)

   B - Carrier

   C - Bucket Pin (1 each side)

   D - Carrier Strap (1 each side)

   Extend bucket cylinders to position the carrier (B) forward.

---




2. Align the top of the carrier with hooks (A).

3. Raise the loader until the carrier engages hooks, then retract bucket cylinders until the bucket rests against the carrier.

4. Prevent possible injury. Make sure that the bucket is properly secured to the carrier.

   Raise the loader to check that carrier straps (D) engage bucket pins (C) on both sides of the bucket.

5. Place the transmission in PARK and shut off the engine.

6. 
   W09797-UN-26AUG08

   E - Storage Position

   F - Quick-Lock Pin

   Remove quick-lock pins (F) from the storage position (E).

---




7. Install quick-lock pins (F) through attachment pins.

Global Carrier (Manual)

1. The attaching procedure is the same for all attachments, bucket attachment shown.

   
   W09830-UN-04SEP08

   A - Latch Lever

   Pull the latch lever (A) outward and rotate upward to lock into place.

---




2. 
   W28373-UN-16JAN18

   A - Carrier Bracket (1 each side)

   B - Guide (1 each side)

   C - Hook (1 each side)

   Extend bucket cylinders to position carrier brackets (A) forward.

---




3. Using guides (B) on the inside of the bar, align carrier brackets (A) under hooks (C) on the bucket and raise the loader until brackets engage hooks.

4. 
   W28374-UN-16JAN18

   A - Tab

   To remove the weight from the edge of the bucket and allow the latch mechanism to contact the tab (A), retract bucket cylinders.

---




5. Prevent possible injury. Make sure that the bucket is properly secured to the carrier.

   
   W28375-UN-16JAN18

   A - Pin (1 each side)

   Latch releases and slides pins (A) into the locked position.

---




6. Raise the loader to check that pins (A) are engaged with the bucket.

Skid-Steer Carrier

1. 
   W08389-UN-29NOV06

   Left-Hand Lock Pin

   
   W09837-UN-10SEP08

   
   W09838-UN-11SEP08

   A - Latch Handle (1 each side)

   B - Lock Pin (1 each side)

   C - Lip

   D - Latch (2 used)

   Make sure both latch handles (A) are up and lock pins (B) are retracted.

   The attaching procedure is the same for all attachments, bucket attachment shown.

   Raise both latch handles (A) into the UP (unlatched) position.

---




2. Raise the loader off the ground.

3. To tilt the carrier forward, extend bucket cylinders.

4. Drive forward and raise the loader until carrier plates are positioned under the lip (C) on the bucket, then retract bucket cylinders.

   The bucket rests against carrier plates.

5. Lower the loader to the ground and shut off the engine.

6. Lower latch handles (A) to engage lock pins (B) with latches (D) on the bucket.

7. Prevent possible injury. Make sure that the bucket is properly secured to the carrier.

   Extent bucket cylinders and apply down-pressure on the bucket against the ground, and verify that pins (B) are engaged in latches (D).

   If the bucket is not securely attached to the skid steer carrier, repeat steps.

Hydraulically Operated Attachment (Grapple)

1. 

   
   X9811-UN-23AUG88

   Escaping fluid under pressure can penetrate the skin, causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Protect hands and body from high-pressure fluids. (See additional information, Avoid High-Pressure Fluids, in Safety section.)

   Before connecting coupler halves, make sure that fittings are free of dirt and debris.

   Relieve the hydraulic pressure. (See Relieve Hydraulic Pressure in Controls section.)

---




2. 
   W20034-UN-14OCT08

   A - Cover

   B - Lever

   C - Knob

   Raise the cover (A).

---




3. Push in the red knob (C) and rotate the lever (B) forward and down, as shown.

4. 
   W20035-UN-14OCT08

   A - Attachment Coupler

   B - Locating Pin (2 used)

   C - Hole (1 each side)

   D - Loader Coupler

   Multicoupler mating halves must align properly or damage to couplers can occur.

---




5. Place the attachment coupler (A) onto the loader coupler (D). Make sure that locating pins (B) on the attachment coupler fit into corresponding holes (C) in the loader coupler.

6. 
   W20036-UN-14OCT08

   E - Lever

   F - Pin (1 each side)

   Rotate the lever (E) up and rearward to engage pins (F) on the attachment coupler, locking coupler halves together.

---