Attach Loader

1. 
   W22802-UN-15AUG12

   A - Distance, 75 mm (3 in)

   Attach the ballast box. (See Attach Ballast Box to Tractor Hitch in Prepare Tractor section.)

---




2. Position the tractor between loader masts.

3. Stop the tractor when backs of loader masts are approximately 75 mm (3 in) (A) ahead of fronts of mounting frames.

4. Place the transmission in PARK and shut off the engine.

5. 

   
   X9811-UN-23AUG88

   Escaping fluid under pressure can penetrate the skin, causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Protect hands and body from high-pressure fluids. (See additional information, Avoid High-Pressure Fluids, in Safety section.)

   Relieve the hydraulic pressure. (See Relieve Hydraulic Pressure in Controls section.)

---




6. 

   
   W09730-UN-22AUG08

   Single-Lever ICV (Option)

   
   W09731-UN-22AUG08

   Mid-Mount (With Couplers)

   A - Loader Hose (4 or 6 used)

   Prevent possible injury caused by unexpected loader movement. Anticipated loader movement responds to the control lever only if the hoses are connected correctly.

   Before connecting the hoses, make sure that fittings are free of dirt and debris.

   Hose connections are identified by matching the color-coded cap on the hose end with the same color-coded plug on the control valve coupler. If caps are missing or not equipped, see Identify Hose Connections in Service section.

   Attach mid-mount couplers (if equipped): Connect loader hoses (A) using color-coded dust caps to match the hoses to couplers.

---




7. 
   W27090-UN-08OCT15

   Mid-Mount (No Couplers)

   A - Loader Hose (4 or 6 used)

   Attach mid-mount SCVs: Connect loader hoses (A) using color-coded dust caps to match the hoses to fittings. Tighten to specification.

   Hose-to-Fitting	Torque	50 N·m (37 lb·ft)

---




8. 
   W21206-UN-13DEC10

   A - Cover

   B - Knob

   Connect the multicoupler (5M series and 5105ML tractors, if equipped):

   1. Raise the cover (A).

   2. Push in the red knob (B) and rotate the lever rearward and down, as shown.

   ---

   
   

   3. 
      W24712-UN-17FEB14

      A - Cover

      B - Chamfered Edge

      C - Loader Coupler

      D - Locating Pin (2 used)

      E - Tractor Coupler

      F - Hole (2 used)

      Multicoupler mating halves must align properly or damage to couplers can occur.

      Place the loader coupler (C) (with the chamfered edge [B] toward the cover [A]) onto the tractor coupler (E). Make sure that locating pins (D) on the loader coupler (C) fit into the corresponding holes (F) in the tractor coupler (E).

   ---

   
   

   4. 
      W21207-UN-13DEC10

      A - Lever

      B - Loader Coupler

      C - Pin (1 each side)

      To engage pins (C) on the loader coupler (B), rotate the lever (A).

---




9. Place the transmission in NEUTRAL.

10. 
    W22803-UN-08AUG12

    A - Pin (1 each side)

    B - Saddle (1 each side)

    Extend lift cylinders until pins (A) on masts contact the front of mounting frame saddles (B) as shown.

---




11. 
    W22804-UN-08AUG12

    A - Mast

    B - Mounting Frame

    C - Parking Stand (2 used)

    Dump the bucket until masts (A) seat in mounting frames (B) on both sides and parking stands (C) are slightly off the ground as shown.

---




12. Place the transmission in PARK and shut off the engine.

13. 
    W22805-UN-23JUL12

    A - Spring Pin (1 each side)

    B - Mast Pin (1 each side)

    C - Parking Stand (2 used)

    D - Spring Pin (1 each side)

    Remove spring pins (A), mast pins (B), and parking stands (C).

---




14. Remove spring pins (D) from the storage location.

15. 
    W28379-UN-16JAN18

    A - Parking Stand (2 used)

    B - Storage Tube

    C - Spring Pin (1 each side)

    Install parking stands (A) into each end of the storage tube (B). Fasten with spring pins (C).

---




16. 
    W22806-UN-08AUG12

    A - Bushing, Mast

    B - Bushing, Frame

    Make sure that mast bushings (A) are aligned with frame bushings (B) on both sides of the loader.

---




17. 
    W21211-UN-17NOV10

    Left-Hand Side Shown

    A - Mast Pin (2 used)

    B - Spring Pin (2 used)

    Install the mast pin (A) on both sides of the loader.

---




18. Fasten with spring pins (B).

19. 
    W09734-UN-04SEP08

    Upper Hose Support

    A - Hose Support (upper)

    B - Spring Pin

    C - Drilled Round-Head Bolt

    Right-hand side (if equipped with mid-mount couplers):

    1. Install the upper hose support (A) on the drilled round-head bolt (C) and fasten with the spring pin (B).

    ---

    
    

    2. 
       W20122-UN-29OCT08

       Lower Hose Support (Right-Hand Side—5M Series and 5105ML Tractors Only)

       D - Hose Support, Lower

       E - Spring Pin

       5M Series and 5105ML tractors only: Install the lower hose support (D) on the bracket, as shown, and fasten with the spring pin (E).

---