CAN bus inbound communications overload. | CAN bus communications overload. Reset the display or turn the power off and then back on. |
When an implement’s object pool is rejected by the VT | There is a technical problem preventing proper operation of the display with the following implement. Please contact implement manufacturer with this information: |
A valid card is inserted that contains bad setup data. | The setup data on the compact flash card is invalid. Please resave the setup data to the card from your computer. |
A valid card is inserted that contains bad setup data that cannot be read by this version of the display software. | The setup data on the compact flash card can not be read by the display. Please update your display software. |
A card is inserted that can not be used by the display | The compact flash card is not compatible with the display. Please use a different card. |
If the user is in the middle of setting up a new operation and they switch to the homepage, the apps on the homepage would be disabled in that case. Similarly, if the user was changing the status of a job, the apps on the homepage would be disabled. In both of these cases there is no error | There is an alarm or pop-up within the GreenStar 2 application that requires your attention. |
Data Card 90% Full | Unload and cleanup data card or insert new data card soon. |
Data Card Full | Unload and cleanup data card or insert new data card. |
VI Implement is removed | Communication lost with ISO implement. If implement was not disconnected, check connections and cycle power. |
Internal Memory Full--From VI Object Pools | Internal memory dedicated to ISO implements is full. Remove implements to free memory space. |
Internal Memory Full-From Documentation and Curved Track data | Internal memory is full. |
New software found for display | New software found for display. (This alarm will re-appear at every power cycle or if card is re-inserted.) |
The following VI(s) are no longer communicating with the display. Check the indicated device(s) and CAN bus wiring. | Some device(s) are no longer communicating with the display. Check the CAN Bus wiring. |
CAN bus inbound communications overload. | CAN Bus communications overload. Reset the display or turn the power off and then back on. |
A failure has been detected in the display’s internal memory. (Reprogramming) | An error occurred during reprogramming. Perform reprogramming process again. If problem reoccurs contact your John Deere dealer. |
Legacy device reprogramming error. Device not reporting version info | An error occurred during reprogramming. Perform reprogramming process again. If problem reoccurs contact your John Deere dealer. |
Legacy device not found while programming product | Device not found while programming product. Check wiring and connectors. |
Attempt to copy the setup data to a “new” card that already has setup data on it | Prior setup data found on card. Select CONTINUE button to overwrite this data. Select CANCEL button to abort the copy to card operation. (If the user decides to continue, there will be a second popup)"Are you sure you want to overwrite?" |
Wrong activation code | Invalid activation code. Please reenter activation code. |
Customer attempts to record boundary when one already exists | Are you sure you want to redefine the boundary? |
All New/Edit Screens: User attempts to create a duplicate name in any of the New/Edit screens | This entry is already being used. Please select a new entry or cancel to modify the entry. |
This alarm will be shown after we have received a touch event for 60 seconds. | The touchscreen is malfunctioning. Try to reboot the device, utilize an external display control, or the bezel keys on the backside of this display for screen response. If problem persists, please contact your John Deere Dealer. |
This alarm will be shown after we have received a touch event for 60 seconds. | A button is malfunctioning. Try to reboot the display. If the problem persists, please contact your John Deere Dealer. |
GPS Alarms For GreenStar Basic/Deluxe | |
200 GPS communications failure | No communication with GPS receiver. Check connections at GPS receiver. |
No GPS. Tracking Disabled | No GPS position available. Verify GPS receiver has clear view of sky. |
No Diff. Tracking Disabled. | No GPS differential correction available. Verify GPS receiver has clear view of sky. |
2D GPS in use. | 2D GPS in use. Verify GPS receiver has clear view of sky. |
Tracking Inaccurate The GPS receiver must be set to report at the 5Hz. Rate. Confirm settings on receiver. | The GPS receiver must be set to report at the 5Hz message output rate. Confirm settings on GPS receiver and change output to 5Hz. (For 3rd-Party Controllers) NOTE: 3rd-Party controllers are controllers using RS232 connection (Field Doc Connect) and ISOBUS compliant controllers supporting Task Controller functionality. |
Language Loading Errors: | |
CRC bad, missing a colon, bad prep header, etc. | Language load detected corrupt file. Reload software to data card. |
Hardware compat. version mismatch. | Invalid hardware for language file. Reload software to data card. |
Software version mismatch. | Language file incompatible with application. Reload software to data card. |
Timeout waiting for CAN62 Response To Request | Device failed to start programming language. Reload software to data card. |
Target sent FAIL in CAN62 Response To Request | Device failed to continue programming language. Reload software to data card. |
Timeout waiting for CAN62 Response To Checksum | Device failed to report a language checksum. Reload software to data card. |
Target sent FAIL in CAN62 Response To Checksum | Device reported an invalid language checksum. Reload software to data card. |
Timeout waiting for CAN62 Response To Remove | Device didn’t respond to the request to remove language. Reload software to data card. |
Target sent FAIL in CAN62 Response To Remove | Device failed to remove a language. Reload software to data card. |
Flash Write Failure. | Device failed while writing language to memory. Reload software to data card. |
Timeout waiting for CAN62 Response To New Data | Device stopped programming language prematurely. Reload software to data card. |
Product ID mismatch | Language is incompatible with loaded product. Reload software to data card. |