|
DTC
|
Code Description
|
Problem
|
Solution
|
|
GR6 158.03
|
High Switched Voltage
|
StarFire™ Receiver is operating with high switched power (greater than 32
V).
|
Check machine’s charging system, wiring, and connections.
|
|
GR6 158.04
|
Low Switched Voltage
|
StarFire™ Receiver is operating with low switched power
(less than 9 V).
|
Check machine’s charging system, wiring, and connections.
|
|
GR6 168.03
|
High Unswitched Voltage
|
Unswitched power to StarFire™ Receiver has high voltage
(greater than 32 V).
|
Check machine’s charging system, wiring, and connections.
|
|
GR6 168.04
|
Low Unswitched Voltage
|
Unswitched power to StarFire™ Receiver has low voltage
(less than 9 V).
|
Check machine’s charging system, wiring, and connections.
|
|
GR6 629.12
|
Reset Occurred
|
Internal hardware reset occurred.
|
Restart receiver and try again.
|
|
GR6 639.12
|
CAN Bus Messages Missing
|
StarFire™ messages are missing from CAN bus.
|
Check receiver harness for faults.
|
|
GR6 639.14
|
StarFire™ CAN in Bus Off State
|
Loss of CAN data.
|
Verify receiver is connected to machine and powered on. Check
receiver harness for faults.
|
|
GR6 841.07
|
Lost Communication with Processor
|
StarFire™ Receiver has lost communication with GPS processor.
|
Disconnect receiver harness from machine to power off and try
again.
|
|
GR6 2850.05
|
Reflected Antenna Power too High
|
Rover real time kinematic (RTK) reflected antenna power too
high.
|
Check rover radio antenna for faults.
|
|
GR6 2854.31
|
Loss of Rover Radio Link
|
RTK radio is not responding.
|
Inspect receiver bracket harness for faults.
|
|
GR6 3141.14
|
GPS Receiver is not authorized to receive corrections on the
RTK Base Station
|
GPS receiver is not authorized on this RTK network.
|
Try an alternate frequency.
|
|
GR6 3141.31
|
GPS corrections license has expired
|
SF3 subscription has expired.
|
Enter a valid SF3 license subscription activation code.
|
|
GR6 3144.13
|
StarFire™ receiver cannot link to StarFire™ network
on alternate frequency
|
StarFire™ signal not found.
|
Try an alternate frequency.
|
|
GR6 516198.16
|
Base position readings exceeded.
|
Bad base position.
|
Check for obstructions or presence of signal interference around
base receiver.
|
|
GR6 522394.13
|
TCM Not Calibrated
|
StarFire™ terrain compensation module (TCM) has not been
calibrated.
|
Recent system changes indicate TCM was reinstalled. Calibrate
TCM to ensure optimized system performance.
|
|
GR6 522552.11
|
StarFire™ Network Problem
|
StarFire™ network encountered a problem.
|
Resolution is in progress. Stand by.
|
|
GR6 523187.02
|
Incorrect license activation received from StarFire™ satellite
|
Invalid over-the-air license received.
|
Verify license type and date and try again.
|
|
GR6 523274.02
|
GPS Position Not Available
|
StarFire™ GPS position is not available.
|
GPS position cannot be computed. Verify receiver has an open
view of sky.
|
|
GR6 523310.02
|
StarFire™ Memory Error
|
StarFire™ Receiver memory error has occurred.
|
Read and write failure. Restart receiver.
|
|
GR6 523348.07
|
TCM Communication Failure
|
TCM communication failure.
|
Restart receiver and try again.
|
|
GR6 523348.16
|
Reported temperature from IMU is outside the calibrated range
|
TCM temperature out of range.
|
Reported temperature from inertial measurement unit (IMU) is
outside of calibrated range. This can lead to inaccurate pitch, roll,
and heading.
|
|
GR6 523348.12
|
TCM Sensor Failure
|
TCM sensor failure.
|
Contact your John Deere dealer.
|
|
GR6 523441.31
|
GPS Height Not Set
|
StarFire™ GPS height dimension not set.
|
Enter TCM height.
|
|
GR6 523442.31
|
Fore/Aft Dimension Not Set
|
TCM fore/aft is not set.
|
Enter TCM fore/aft.
|
|
GR6 523773.03
|
CAN HI Voltage Too High
|
StarFire™ CAN HI voltage is too high.
|
Check machine’s wiring.
|
|
GR6 523773.04
|
CAN HI Voltage Too Low
|
StarFire™ CAN HI voltage is too low
|
Check machine’s wiring.
|
|
GR6 523774.03
|
CAN LO Voltage Too High
|
StarFire™ CAN LO voltage is too high.
|
Check machine’s wiring.
|
|
GR6 523774.04
|
CAN LO Voltage Too Low
|
StarFire™ CAN LO voltage is too low
|
Check machine’s wiring.
|
|
GR6 524209.16
|
Rover Too Far From Base
|
Rover RTK is too far from base station for valid corrections.
|
Drive closer to base station or connect to an alternate base
station.
|
|
GR6 524257.14
|
RTK Base Station Survey Mode
|
RTK base station is in survey mode.
|
Corrections are unavailable while RTK base station is in survey
mode.
|
|
GR6 524257.16
|
RTK Base Station Moved
|
RTK base station has been moved.
|
Corrections are not valid. Connect to an alternate base station.
|
|
GR6 524257.19
|
Multiple RTK Base Stations
|
Multiple RTK base stations detected.
|
Interference between neighboring RTK base stations. Adjust RTK
network settings to unique values.
|