|
Address
|
Description
|
|
0
|
Display device picture
|
|
1
|
Recall diagnostic trouble codes (DTCs)
|
|
2
|
System beep
|
|
3
|
Universal time coordinated (UTC) time
|
|
4
|
Universal time coordinated (UTC) date
|
|
5
|
Corrected latitude (post inertial measurement unit [IMU])
|
|
6
|
Corrected longitude (post IMU)
|
|
7
|
Altitude (post IMU)
|
|
8
|
Corrected course (IMU yaw)
|
|
9
|
Speed
|
|
10
|
Position mode
|
|
11
|
Differential mode
|
|
12
|
Accuracy indicator
|
|
13
|
Global positioning system (GPS) signal quality indicator
|
|
14
|
StarFire™ signal strength
|
|
15
|
Corrections age
|
|
16
|
Elevation mask
|
|
17
|
Satellites tracked
|
|
18
|
Satellites used in velocity solution
|
|
19
|
Position dilution of precision (PDOP)
|
|
20
|
Satellites used in position solution
|
|
22
|
License Subscription Level
|
|
23
|
SF3 License Subscription End (Expiration Date)
|
|
24
|
SF3 License Subscription Days Left
|
|
25
|
Switched voltage
|
|
26
|
Unswitched voltage
|
|
27
|
CAN high voltage
|
|
28
|
CAN low voltage
|
|
29
|
Hour meter
|
|
30
|
Hours on after shutdown
|
|
34
|
StarFire™ height dimension
|
|
35
|
StarFire™ fore/aft dimension
|
|
36
|
StarFire™ mount direction
|
|
37
|
Real time kinematic (RTK) base status
|
|
38
|
L band reception index
|
|
39
|
StarFire™ correction frequency
|
|
41
|
RS232 baud rate
|
|
42
|
RS232 National Marine Electronics Association (NMEA) message
rate
|
|
43
|
GGA output status
|
|
44
|
GSA output status
|
|
45
|
RMC output status
|
|
46
|
VTG output status
|
|
47
|
ZDA output status
|
|
48
|
Pitch angle from IMU
|
|
49
|
Roll angle from IMU
|
|
51
|
X-axis gyroscope output (deg/s)
|
|
52
|
Y-axis gyroscope output (deg/s)
|
|
53
|
Z-axis gyroscope output (deg/s)
|
|
54
|
Raw latitude (uncorrected)
|
|
55
|
Raw longitude (uncorrected)
|
|
56
|
Raw altitude (uncorrected)
|
|
57
|
Raw course (uncorrected)
|
|
58
|
Roll field calibration value
|
|
59
|
Steering controller type
|
|
60
|
Transmission direction (0 = neutral, 1 = forward, 2 = reverse,
0xFF = unknown)
|
|
62
|
CAN source address
|
|
63
|
Radio frequency (RF) application-specific integrated circuit
(ASIC) 0 high band gain (dB), 2 decimals
|
|
64
|
RF ASIC 0 low band gain (dB), 2 decimals
|
|
65
|
RF ASIC 1 high band gain (dB), 2 decimals
|
|
66
|
RF ASIC 1 low band gain (dB), 2 decimals
|
|
70
|
RTK operating mode
|
|
71
|
Radio type
|
|
72
|
Radio state
|
|
73
|
Remaining RTK Extend™ (RTK-X) seconds left
|
|
74
|
Remaining time for RTK base station survey (0 means done)
|
|
75
|
Distance from RTK base station
|
|
77
|
RTK noise level (FreeWave® ) RTK signal level (satellite)
|
|
78
|
RTK network identification (ID)
|
|
79
|
RTK channel (FreeWave®) RTK time slot (satellite)
|
|
80
|
RTK percent packet received in last 30 s
|
|
81
|
RTK base station battery voltage
|
|
82
|
RTK radio hardware serial number
|
|
83
|
RTK radio application software version number
|
|
84
|
GLONASS enable (0 = disable, 1 = enable, 2 = G1 only)
|
|
86
|
External antenna status
|
|
87
|
Buffer Overflow (or Buffer Full) Count
|
|
88
|
Drive A (eMMC) is not mounted. Indicates hardware failure or
file allocation table (FAT) drive error.
|
|
89
|
Pitch field calibration value
|
|
90
|
L-band frequency search mode
|
|
91
|
Vertical accuracy indicator (mm)
|
|
92
|
Mobile RTK subscription end date
|
|
93
|
Days remaining for Mobile RTK subscription
|
|
94
|
Rapid Recovery (0 = off, 1 = on)
|
|
95
|
INS solution use of fore/aft values (0 = disabled, 1 = enabled)
|
|
97
|
Mobile RTK MTG NTRIP (Network Transport of RTCM data over IP)
(NTRIP) Connection Status [format: A,B,C,D,E]
A = server proxy login state
B = cellular network call state
C = GPS fix data JD GGA state
D = cellular signal strength
E = cellular modem state information (idle = 0, initializing
service = 1, sending corrections = 2)
|
|
98
|
Mobile RTK third-party GLONASS enable or disable
0 = disabled (default)
1 = enabled only if 4092 message is detected
2 = enabled even if 4092 message is not detected
|
|
99
|
Current oscillator temperature, updated every 1 Hz
|
|
100
|
Minimum temperature in current power-on cycle with timestamp
|
|
101
|
Maximum temperature in current power-on cycle with timestamp
|
|
102
|
Lifetime minimum temperature, read and saved from/into NVRAM
|
|
103
|
Lifetime minimum temperature, read and saved from/into NVRAM
|
|
104
|
Local Antenna Type One Version–NONE if not available
|
|
105
|
Local Antenna Type Two Version–NONE if not available
|
|
106
|
Remote Base Station Antenna Type Version–NONE if not available
|
|
107
|
Local Antenna Type One Number–0 if not available
|
|
108
|
Local Antenna Type Two Number–0 if not available
|
|
109
|
Remote Base Station Antenna Type Number–0 if not available
|
|
120
|
Preferred virtual terminal (VT) functionality
|
|
121
|
Preferred VT wait time
|
|
130
|
Third to last activation error code
|
|
131
|
Second to last activation error code
|
|
132
|
Most recent license subscription and activation error codes
|
|
140
|
24 h survey position standard deviation, east (in or cm)
|
|
141
|
24 h survey position standard deviation, north (in or cm)
|
|
142
|
24 h survey position standard deviation, up (in or cm)
|
|
143
|
Percentage of time that GPS accuracy indicator (GAI) is less
than 7 (percentage value)
|
|
144
|
Number of times during last 24 h survey unit did not navigate
in SF2 mode
|
|
145
|
Anti-scintillation on/off (Iono-free RTK)
|
|
146
|
RTK engine multipath mitigation setting
|
|
147
|
Y-axis accelerometer output, float, m/s2, 3 decimal places
|
|
148
|
X-axis accelerometer output, float, m/s2, 3 decimal places
|
|
149
|
Z-axis accelerometer output, float, m/s2, 3 decimal places
|
|
150
|
Moving base RTK (MBRTK) missing counts
|
|
151
|
MBRTK massage 0x23 latency
|
|
152
|
Figure of Merit (FOM) cm (range 1–255 cm)
|
|
160
|
Total count since last base station quality indicator (BSQI)
reset (in seconds)
|
|
161
|
Base station StarFire™ operating mode
|
|
180
|
Factory settings reset
|
|
181
|
X axis accelerometer bias
|
|
182
|
Y-axis accelerometer bias (mm/s2)
|
|
183
|
Z-axis accelerometer bias (mm/s2)
|
|
184
|
Enable/disable use of tidal models in nav solution (0–off,
1–on)
|
|
185
|
Enable/disable SF3 in-season repeatability
|
|
186
|
Nav Data Model State (0 - invalid, - 1 valid)
|
|
187
|
Last TCM Calibration (UTC)
|
|
191
|
IMU software version
|
|
200
|
Average central processing unit (CPU) usage last 1 s
|
|
201
|
Enable or disable interference data logging
|
|
231
|
John Deere Operating System (JDOS) part number
|
|
232
|
JDOS version number
|
|
235
|
Hardware part number
|
|
236
|
Hardware serial number
|
|
239
|
ANTSWAP
|