|
10.13
|
Display Not Detected
|
Verify that display is connected and reboot system.
|
|
158.03
|
Switched Supply Voltage High
|
Check connections and diagnostic LEDs on John Deere Rate Controller
2000 and reference the Operator’s Manual.
|
|
158.04
|
Switched Supply Voltage Low
|
Check connections and diagnostic LEDs on John Deere Rate Controller
2000 and reference the Operator’s Manual.
|
|
628.12
|
Bad Intelligent Device or Component
|
Check connections and diagnostic LEDs on John Deere Rate Controller
2000 and reference the Operator’s Manual.
Reboot system if the problem persists.
|
|
630.13
|
System Configuration or Calibration Required
|
Reference Operator’s Manual and calibrate system.
|
|
3132.04
|
Pressure 1—Sensor Not Detected
|
Verify pressure sensor installation.
|
|
3132.13
|
Pressure 1—Sensor Not Calibrated
|
Reference Operator’s Manual and calibrate system.
|
|
3132.16
|
Pressure 1—Pressure Above Maximum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
3132.18
|
Pressure 1—Pressure Below Minimum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
4305.00
|
Application Speed Exceeded
|
Operate at lower application speeds.
|
|
4305.02
|
Speed Is Below Operational Speed
|
Operate at higher application speeds.
|
|
517247.04
|
Pressure 2—Sensor Not Detected
|
Verify pressure sensor installation.
|
|
517247.13
|
Pressure 2—Sensor Not Calibrated
|
Reference Operator’s Manual and calibrate system.
|
|
517247.16
|
Pressure 2—Pressure Above Maximum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517247.18
|
Pressure 2—Pressure Below Minimum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517248.00
|
Product 1 Rate—No Rate Expected
|
Verify that hydraulic system is turned off. Verify that master
switch is off.
|
|
517248.01
|
Product 1 Rate—No Rate Detected
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517248.13
|
Product 1 Rate—Calibration Required
|
Reference Operator’s Manual and calibrate system.
|
|
517248.15
|
Product 1 Rate—Rate Above Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517248.17
|
Product 1 Rate—Rate Below Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517248.18
|
Product 1 Rate—Volume Per Minute Below Minimum
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517248.31
|
Product 1 Rate—No RPM speed
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517249.17
|
Product 2 Injection—Pump Lost Communication
|
Check injection pump connections.
|
|
517250.01
|
Product 2 Injection—Injection Pressure Below Carrier Pressure
|
Reference Raven Industries for more information on Raven Direct
Injection systems.
|
|
517251.17
|
Product 3 Injection—Pump Lost Communication
|
Check injection pump connections.
|
|
517252.01
|
Product 3 Injection—Injection Pressure Below Carrier Pressure
|
Reference Raven Industries for more information on Raven Direct
Injection systems.
|
|
517253.17
|
Product 4 Injection—Pump Lost Communication
|
Check injection pump connections.
|
|
517254.01
|
Product 4 Injection—Injection Pressure Below Carrier Pressure
|
Reference Raven Industries for more information on Raven Direct
Injection systems.
|
|
517255.17
|
Product 5 Injection—Pump Lost Communication
|
Check injection pump connections.
|
|
517256.01
|
Product 5 Injection—Injection Pressure Below Carrier Pressure
|
Reference Raven Industries for more information on Raven Direct
Injection systems.
|
|
517257.15
|
RPM 1—Above Maximum Threshold
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517257.17
|
RPM 1—Below Minimum Threshold
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517258.00
|
Section Valve Master Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517258.01
|
Section Valve Master Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517259.00
|
Section Valve 1 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517259.01
|
Section Valve 1 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517260.00
|
Section Valve 2 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517260.01
|
Section Valve 2 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517261.00
|
Section Valve 3 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517261.01
|
Section Valve 3 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517262.00
|
Section Valve 4 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517262.01
|
Section Valve 4 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517263.00
|
Section Valve 5 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517263.01
|
Section Valve 5 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517264.00
|
Section Valve 6 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517264.01
|
Section Valve 6 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517265.00
|
Section Valve 7 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517265.01
|
Section Valve 7 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517266.00
|
Section Valve 8 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517266.01
|
Section Valve 8 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517267.00
|
Section Valve 9 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517267.01
|
Section Valve 9 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517268.00
|
Section Valve 10 Open When It Should Be Closed
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517268.01
|
Section Valve 10 Closed When It Should Be Open
|
Check valve functionality.
Select Menu button > John Deere Rate Controller 2000 button
> Diagnostics softkey > Test tab.
|
|
517269.01
|
Valve Power Sense Circuit 1 Error
|
Check connections and diagnostic LEDs on John Deere Rate Controller
2000 and reference the Operator’s Manual.
|
|
517270.01
|
Valve Power Sense Circuit 2 Error
|
Check connections and diagnostic LEDs on John Deere Rate Controller
2000 and reference the Operator’s Manual.
|
|
517271.01
|
Valve Power Harness Error
|
Check connections and diagnostic LEDs on John Deere Rate Controller
2000 and reference the Operator’s Manual.
|
|
517272.01
|
Low Current Power Loss
|
Check connections and diagnostic LEDs on John Deere Rate Controller
2000 and reference the Operator’s Manual.
|
|
517273.01
|
Product Pump 1—Pump Dry (PWM control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517273.07
|
Product Pump 1—Raven AccuFlow HP™ Plus Boost Pump Fault
|
Reference Raven Industries for more information on Raven Direct
Injection systems.
|
|
517273.18
|
Pump 1—Pump Dry (servo control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517274.01
|
Test Canceled
|
No checks needed.
|
|
517296.04
|
Pressure 3—Sensor Not Detected
|
Verify pressure sensor installation.
|
|
517296.13
|
Pressure 3—Sensor Not Calibrated
|
Reference Operator’s Manual and calibrate system.
|
|
517296.16
|
Pressure 3—Pressure Above Maximum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517296.18
|
Pressure 3—Pressure Below Minimum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517297.04
|
Pressure 4—Sensor Not Detected
|
Verify pressure sensor installation.
|
|
517297.13
|
Pressure 4—Sensor Not Calibrated
|
Reference Operator’s Manual and calibrate system.
|
|
517297.16
|
Pressure 4—Pressure Above Maximum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517297.18
|
Pressure 4—Pressure Below Minimum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517298.04
|
Pressure 5—Sensor Not Detected
|
Verify pressure sensor installation.
|
|
517298.13
|
Pressure 5—Sensor Not Calibrated
|
Reference Operator’s Manual and calibrate system.
|
|
517298.16
|
Pressure 5—Pressure Above Maximum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517298.18
|
Pressure 5—Pressure Below Minimum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517299.04
|
Pressure 6—Sensor Not Detected
|
Verify pressure sensor installation.
|
|
517299.13
|
Pressure 6—Sensor Not Calibrated
|
Reference Operator’s Manual and calibrate system.
|
|
517299.16
|
Pressure 6—Pressure Above Maximum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517299.18
|
Pressure 6—Pressure Below Minimum Set Point
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517300.00
|
Product 2 Rate—No Rate Expected
|
Verify that hydraulic system is turned off. Verify master switch
is off.
|
|
517300.01
|
Product 2 Rate—No Rate Detected
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517300.13
|
Product 2 Rate—Calibration Required
|
Reference Operator’s Manual and calibrate system.
|
|
517300.15
|
Product 2 Rate—Rate Above Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517300.17
|
Product 2 Rate—Rate Below Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517300.18
|
Product 2 Rate—Volume Per Minute Below Minimum
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517300.31
|
Product 2 Rate—No RPM speed
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517301.00
|
Product 3 Rate—No Rate Expected
|
Verify that hydraulic system is turned off. Verify master switch
is off.
|
|
517301.01
|
Product 3 Rate—No Rate Detected
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517301.13
|
Product 3 Rate—Calibration Required
|
Reference Operator’s Manual and calibrate system.
|
|
517301.15
|
Product 3 Rate—Rate Above Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517301.17
|
Product 3 Rate—Rate Below Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517301.18
|
Product 3 Rate—Volume Per Minute Below Minimum
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517301.31
|
Product 3 Rate—No RPM Speed
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517302.00
|
Product 4 Rate—No Rate Expected
|
Verify that hydraulic system is turned off. Verify master switch
is off.
|
|
517302.01
|
Product 4 Rate—No Rate Detected
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517302.13
|
Product 4 Rate—Calibration Required
|
Reference Operator’s Manual and calibrate system.
|
|
517302.15
|
Product 4 Rate—Rate Above Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517302.17
|
Product 4 Rate—Rate Below Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517302.18
|
Product 4 Rate—Volume Per Minute Below Minimum
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517302.31
|
Product 4 Rate—No RPM Speed
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517303.00
|
Product 5 Rate—No Rate Expected
|
Verify that hydraulic system is turned off. Verify master switch
is off.
|
|
517303.01
|
Product 5 Rate—No Rate Detected
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517303.13
|
Product 5 Rate—Calibration Required
|
Reference Operator’s Manual and calibrate system.
|
|
517303.15
|
Product 5 Rate—Rate Above Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517303.17
|
Product 5 Rate—Rate Below Target
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517303.18
|
Product 5 Rate—Volume Per Minute Below Minimum
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517303.31
|
Product 5 Rate—No RPM Speed
|
Verify that hydraulic system is functioning. Adjust control
valve settings as needed.
|
|
517304.15
|
RPM 2—Above Maximum Threshold
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517304.17
|
RPM 2—Below Minimum Threshold
|
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517305.01
|
Product Pump 2—Pump Dry (PWM control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517305.18
|
Product Pump 2—Pump Dry (servo control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517306.01
|
Product Pump 3—Pump Dry (PWM control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517306.18
|
Product Pump 3—Pump Dry (servo control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517307.01
|
Product Pump 4—Pump Dry (PWM control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517307.18
|
Product Pump 4—Pump Dry (servo control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517308.01
|
Product Pump 5—Pump Dry (PWM control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517308.18
|
Product Pump 5—Pump Dry (servo control valve)
|
Turn off master switch and verify that there is product within
the tank.
|
|
517309.31
|
Product Bin/Tank 1—Empty
|
Turn off master switch and verify that there is product within
the bin or tank.
|
|
517310.31
|
Product Bin/Tank 2—Empty
|
Turn off master switch and verify that there is product within
the bin or tank.
|
|
517311.31
|
Product Bin/Tank 3—Empty
|
Turn off master switch and verify that there is product within
the bin or tank.
|
|
517312.31
|
Product Bin/Tank 4—Empty
|
Turn off master switch and verify that there is product within
the bin or tank.
|
|
517313.31
|
Product Bin/Tank 5—Empty
|
Turn off master switch and verify that there is product within
the bin or tank.
|
|
517314.17
|
Product Bin/Tank 1—Low
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517315.17
|
Product Bin/Tank 2—Low
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517316.17
|
Product Bin/Tank 3—Low
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517317.17
|
Product Bin/Tank 4—Low
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517318.17
|
Product Bin/Tank 5—Low
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517319.1
|
Product 1 Shaft Sensor
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517320.1
|
Product 2 Shaft Sensor
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517321.1
|
Product 3 Shaft Sensor
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517322.1
|
Product 4 Shaft Sensor
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517323.1
|
Product 5 Shaft Sensor
|
Turn off master switch and verify that there is product within
the bin or tank.
Check settings within Alarms tab and adjust as needed.
Select Menu button > John Deere Rate Controller 2000 button
> Setup softkey > Alarms tab.
|
|
517324.01
|
Product 1 Dual Encoder
|
The rate difference between the left and right encoder has exceeded
the allowed tolerance.
(Reference Operator’s Manual and calibrate system.)
|
|
517325.01
|
Product 2 Dual Encoder
|
The rate difference between the left and right encoder has exceeded
the allowed tolerance.
(Reference Operator’s Manual and calibrate system.)
|
|
517326.01
|
Product 3 Dual Encoder
|
The rate difference between the left and right encoder has exceeded
the allowed tolerance.
(Reference Operator’s Manual and calibrate system.)
|
|
517327.01
|
Product 4 Dual Encoder
|
The rate difference between the left and right encoder has exceeded
the allowed tolerance.
(Reference Operator’s Manual and calibrate system.)
|
|
517328.01
|
Product 5 Dual Encoder
|
The rate difference between the left and right encoder has exceeded
the allowed tolerance.
(Reference Operator’s Manual and calibrate system.)
|
|
523350.08
|
Implement Height Switch Malfunction
|
Verify that implement is functioning properly.
|