Attach 220R Loader

1. 
   W27550-UN-08JUL16

   Start the engine.

---




2. Drive forward and center the tractor between the loader masts. Continue forward, aligning the loader masts with mounting frames.

3. Engage the park brake or place the transmission in PARK.

4. Shut off the engine.

5. Relieve the hydraulic pressure. (See Relieve Hydraulic Pressure in Controls section.)

6. 
   W27693-UN-12OCT16

   A - Hose Bundle

   B - Hose Guide

   If equipped with a multicoupler, route the hose bundle (A) into the hose guide (B).

---




7. 
   W27019-UN-09SEP15

   
   W27020-UN-09SEP15

   A - Locating Pin (2 used)

   B - Hole (2 used)

   C - Coupler, Loader Half

   D - Pin (1 each side)

   E - Cover

   F - Red Knob

   G - Coupler, Tractor Half

   H - Handle

   Connect hydraulics—multicoupler:

   1. Raise the cover (E).

   2. Push in the red knob (F) and rotate the handle (H) upward, as shown.

   3. Multicoupler mating halves must align properly or damage to couplers can occur.

      Place the loader coupler (C), into the tractor coupler (G) by aligning pins (A) with holes (B).

   4. Rotate the handle (H) downward to engage pins (D) on the loader coupler. Continue to rotate the handle all the way down until a “click” is heard, locking couplers together.

---




8. 

   
   W27052-UN-09SEP15

   A - Coupler, Female (4 used)

   B - Coupler, Male (4 used)

   C - Cap (4 used)

   D - Plug (4 used)

   Prevent possible injury caused by an unexpected loader movement. The anticipated loader movement responds to the multi-function lever only if the hoses are connected correctly.

   Avoid damage to the loader hoses. Route the hoses above mounting frames.

   Match the color-coded cap with the same color-coded plug. If caps or plugs are missing, see Identify Hose Connections in Service section.

   Connect hydraulics—quick couplers:

   1. Remove the protective cap from the hose and plug from the coupler.

   2. Push back the collar on the female coupler (A) and insert the male coupler (B).

   3. Connect the cap (C) and plug (D) together.

   4. Repeat procedure for all the remaining hose connections.

   Cap and Plug Color	Hydraulic Function
   Black	Bucket Cylinder—Rollback
   Yellow	Bucket Cylinder—Dump
   Blue	Lift Cylinder—Raise
   Red	Lift Cylinder—Lower

---




9. 
   W27165-UN-10DEC15

   Right-Hand Side Shown

   A - Notch

   B - Bushing

   Start the engine.

---




10. If necessary, continue to drive forward keeping the bushing (B) on the mounting frame in alignment with the notch (A) in masts.

11. Place the transmission in NEUTRAL.

12. 
    W27551-UN-08JUL16

    A - Mast

    B - Parking Stand

    C - Weight Bracket

    Make sure that masts are fully seated on mounting frames.

    Retract lift cylinders. Masts (A) lower onto mounting frames and parking stand (B) raises up below the weight bracket (C).

---




13. 
    W27552-UN-08JUL16

    
    W27056-UN-10SEP15

    Use a combination of extending bucket cylinders and retracting lift cylinders until the loader masts move back and latches lock over mounting frame bushings.

---




14. Verify proper attachment, retract lift cylinders until the tractor wheels raise off the ground, then raise the loader to lift the bucket from the ground.