Controls-Steering Console

A-Stop Indicator:

On machines (S.N. 8844645-) the red OVERHEAT light will indicate a medium or high level alarm by either flashing (medium level) or coming on steady (high level). The red OVERHEAT light is also used to display diagnostic trouble codes (DTC) that may be active or stored in the ECU.

On machines (S.N. 882700-8844644) the red STOP light will indicate a medium or high level alarm by either flashing (medium level) or coming on steady (high level). The red STOP light is also used to display diagnostic trouble codes (DTC) that may be active or stored in the ECU.

On machines (S.N. -882699) the red STOP light will come on steady (high level) only.

IMPORTANT: If the STOP indicator comes on steady (high level) and alarm sounds for more than ten seconds with engine oil pressure indicator on, stop machine immediately and investigate cause of problem.

If the STOP indicator comes on steady (high level) and alarm sounds for more than ten seconds with engine coolant temperature indicator on, reduce load and run engine for one to two minutes at slow idle to allow time to cool. If light continues to stay on, stop engine and investigate problem. Do not re-start engine until problem has been corrected.

The STOP indicator comes on steady (high level) and alarm sounds when:

  • Engine oil pressure is low.
  • Engine coolant temperature is excessively high.
  • On machine (S.N. 882700- ) Diagnostic Trouble Code (DTC) is stored in the ECU. See your authorized dealer.
T104939
T196286A


A-Stop Indicator
B-Key Switch
C-Fuel Gauge
D-Hour Meter
E-Work and Drive Lights Switch
F-Warning Lights Switch
G-Mechanical Front Wheel Drive Switch-If Equipped
H-Turn Signal Switch
I-Park Brake Switch
J-Start Aid Switch
K-Horn

OUO1030,0000732 -19-02MAR07-1/3

On machine (S.N. 882700-8844644) the STOP indicator flashes (medium level) and alarm sounds when:

  • Diagnostic Trouble Code (DTC) is stored in the ECU. See your authorized dealer.

On machine (S.N. 8844645-) the STOP indicator flashes (medium level) and alarm sounds when:

  • Diagnostic Trouble Code (DTC) is stored in the ECU. See your authorized dealer.

B-Key Switch

C-Fuel Gauge: The gauge shows the level of fuel in the tank.

D-Hour Meter: Use hour meter to determine when to perform service and maintenance procedures.

E-Work and Drive Lights Switch: Push switch to operate work and drive lights, tail lights, and front work lights, if equipped. The switch has three positions:

  • Push upper half to turn work and drive lights, tail lights, and front work lights, if equipped, on.
  • Push to middle position to turn work and drive lights and tail lights on.
  • Push lower half to turn work and drive lights, tail lights, and front work lights, if equipped, off.

F-Warning Lights Switch: Push upper half of switch to turn warning lights on. When warning lights switch is ON, warning lights indicator, left turn indicator, and right turn indicator will flash. Push lower half of switch to turn warning lights off.

G-Mechanical Front Wheel Drive Switch-If Equipped: Push top half of switch up to engage the MFWD axle. Push bottom half of switch to disengage the MFWD axle.

H-Turn Signal Switch: Push switch to signal turning direction. The switch has three positions:

  • Push left half to signal left turn. Left turn indicator will flash.

OUO1030,0000732 -19-02MAR07-2/3

  • Middle position is OFF. Indicators will not flash unless warning lights switch is ON.
  • Push right half to signal right turn. Right turn indicator will flash.

NOTE: When turn signal is applied with warning lights on, direction light will continue to blink while other amber light illuminates steady.

I-Park Brake Switch: Push top half of switch to engage park brake. Push bottom half of switch to disengage park brake.

J-Start Aid Switch-If Equipped: Press and hold button when engine is cold and cranking to inject starting fluid into engine during cold weather start-up.

K-Horn: Press button to sound horn.

OUO1030,0000732 -19-02MAR07-3/3