210LE Landscape Loader Dimensions
|
TX,9000,BG375 -19-04MAR08-1/3 |
|
NOTE: Specifications and design subject to change without notice. Whenever applicable, specifications are in accordance with SAE standards unless otherwise noted. These specifications are based on a standard |
machine with 16.9 x 24 R4 rear tires; 12 x 16.5 NHS front tires; 0.76 m 3 (1.0 cu. yd.) loader bucket; ROPS/FOPS; full fuel tank and 79 kg (175 lb) operator. |
| Item | Measurement | Specification |
|---|---|---|
|
A-Maximum height to bucket hinge pin |
Height | 3.47 m |
| 11 ft 5 in. | ||
|
B-Dump clearance, bucket at 45° |
Clearance | 2.6 m |
| 8 ft 5 in. | ||
|
C-Bucket pin 280 mm (11 in.) off ground |
Angle | 44° |
|
D-Maximum bucket dump angle |
Angle | 42° at full height |
|
E-Reach at full height |
Distance | 875 mm |
| 34.5 in. | ||
|
-Bucket at 45° |
Distance | 940 mm |
| 37 in. | ||
|
F-Rear axle to rear of hitch (S.N. -880053) |
Distance | 1.07 m |
| 3 ft 6 in. | ||
|
F-Rear axle to rear of hitch (S.N. 880054- ) |
Distance | 1.14 m |
| 3 ft 9 in. | ||
|
G-Dig below ground-bucket level |
Depth | 245 mm |
| 9.64 in. | ||
|
H-Front wheel to loader dig position |
Distance | 1.98 m |
| 6 ft 6 in. | ||
|
I-Wheel Base |
Distance | 2.11 m |
| 6 ft 11 in. | ||
|
J-Height to ROPS top |
Height | 2.48 m |
| 8 ft 2 in. | ||
|
K-Overall length (S.N. -880053) |
Length | 5.17 m |
| 16 ft 11 in. | ||
|
K-Overall length (S.N. 880054- ) |
Length | 5.23 m |
| 17 ft 2 in. |
TX,9000,BG375 -19-04MAR08-2/3 |
| Item | Measurement | Specification |
|---|---|---|
|
L-Lower link pin center |
Distance | 39.7 mm |
| 1.5 in. | ||
|
M-Top link hole height |
Height | 783 mm |
| 30.8 in. | ||
|
N-Rear axle height |
Height | 584 mm |
| 23.0 in. | ||
|
O-Top link hole from rear axle |
Distance | 450 mm |
| 17.7 in. | ||
|
P-Height of lower link point |
Height | 465 mm |
| 18.3 in. | ||
|
Q-Low link point from rear axle |
Distance | 356 mm |
| 14.0 in. | ||
|
R-Pitch cylinder-Retracted |
Length | 572 mm |
| 22.5 in. | ||
|
-Pitch cylinder-Extended |
Length | 798 mm |
| 31.0 in. | ||
|
S-Lower link length |
Length | 749 mm |
| 29.5 in. | ||
|
T-Maximum height lower link-Nominal |
Height | 714 mm |
| 28.1 in. | ||
|
T-Maximum height lower link-Tilt Cylinder Retracted |
Height | 902 mm |
| 35.5 in. | ||
|
U-Minimum height lower link |
Height | 196 mm |
| 7.7 in. | ||
|
V-Height of drawbar |
Height | 325 mm |
| 12.8 in. | ||
|
W-Hitch pin from center axle |
Distance | 843 mm |
| 33.2 in. | ||
|
X-Machine width |
Width | 2184 mm |
| 7 ft 2 in. |
TX,9000,BG375 -19-04MAR08-3/3 |