Instrument Panel Functions

1. Cold Start Indicator: Indicator lights when key switch is turned clockwise to ON position. Indicator will go out after 20 seconds, depending on engine temperature, indicating that preheating is completed.
2. Coolant Level Indicator:

   IMPORTANT: If low coolant level indicator lights, stop machine and shut down engine immediately to prevent engine damage.

   NOTE: Low engine coolant level indicator will flash briefly during start-up when ignition key is turned to the ON position.
   

   Indicator lights when engine coolant level is low.

3. Engine Service Indicator (Marked Engine Fault): Engine service indicator lights and stays lit when an engine service code has been detected.
4. Secondary Steering Indicator (Marked Emergency Steering):

   CAUTION: If there is an engine or main pump malfunction, the ground-driven secondary steering system will enable operator to steer machine to a safe stop.

   Indicator will light when secondary steering system is activated. Stop machine and take corrective action. Secondary steering system is ground driven and not intended for continuous use.

5. Battery Charge Indicator: Indicator lights when alternator output is low.
6. Transmission Retarder Indicator: Indicator lights when transmission retarder is engaged.
7. Transmission Service Indicator (Marked Transmission Fault): Transmission service indicator lights and stays lit when a transmission clutch slippage service code has been detected.
8. Left Turn Indicator: Indicator lights when left turn indicator is switched ON.
9. Service Required Indicator: Indicator lights if service is required. It is not necessary to stop engine immediately, but cause should be investigated and corrected as soon as possible.
10. High Beam Indicator: Indicator lights when headlight high beams are ON.
11. Engine Overspeed Indicator:

    IMPORTANT: If engine overspeed indicator lights, reduce engine speed immediately using the service brake.

    DO NOT exceed 2800 rpm or serious engine or transmission damage may occur.

    Indicator lights when engine speed exceeds 2800 rpm.

12. Right Turn Indicator: Indicator lights when right turn indicator is switched ON.
13. Message Display: Displays machine information for operator.
14. Park Brake Indicator: Indicator lights when park brake is engaged and transmission control lever is in neutral.
15. Brake Oil Pressure Indicator: Indicator lights when brake oil pressure is low or brake accumulator has lost its charge. Stop machine immediately and engage park brake. Take corrective action.
16. Brake Temperature Indicator: Indicator lights when brake temperature is too high.
17. Hydraulic Oil Temperature Indicator: Indicator lights when hydraulic oil temperature exceeds 104°C (220°F). If hydraulic oil temperature is too high, stop work. Allow engine to operate at high idle for 3 minutes and allow oil to cool. If indicator stays on, stop machine and see your authorized dealer.
18. Dump Body Raised Indicator (Marked Bin Up): Indicator lights when body is raised off the frame.
19. Inter-Axle Lock Indicator (Marked Inter-Axle Diff Lock): Indicator lights when inter-axle lock is engaged.
20. Differential Lock Indicator (Marked Diff Lock): Not used.
21. Data Display: Displays machine information.
22. Menu Button: Used to navigate through Monitor Display Unit.
23. Back Button: Used to navigate through Monitor Display Unit.
24. Next Button: Used to navigate through Monitor Display Unit.
25. Select Button: Used to navigate through Monitor Display Unit.
26. Fuel Gauge: Gauge indicates fuel level in tank.

    Always fill fuel tank at end of day to eliminate condensation in fuel tank.

27. Speedometer: Speedometer indicates travel speed in kilometers per hour (km/hr) or miles per hour (mph).
28. Transmission Oil Temperature Gauge:

    CAUTION: DO NOT exceed maximum transmission operating temperature of 145°C (293°F) to avoid damage to the transmission.

    Gauge indicates temperature of transmission oil. Normal operating temperature is indicated by green zone. If indicator points to red zone, allow transmission to cool.

29. Coolant Temperature Gauge:

    CAUTION: To prevent machine damage, DO NOT operate machine when engine coolant temperature is high.

    Gauge indicates temperature of engine coolant. Normal operating temperature is indicated by the green zone. If indicator points to red zone, stop machine and allow engine to cool.

30. Air Pressure Gauge:

    CAUTION: To prevent personal injury or machine damage, DO NOT operate machine when air pressure is low.

    Gauge indicates system air pressure. Normal operating pressure is indicated by the green zone. If indicator points to red zone, stop machine and take corrective action.

31. Engine Oil Pressure Gauge:

    CAUTION: To prevent machine damage, DO NOT operate machine when engine oil pressure is low.

    Gauge indicates engine oil pressure. Normal operating pressure is indicated by the green zone. If indicator points to red zone, stop machine and take corrective action.