OMW52341: 563 Loader, Block File: LD45720_000013B_19

Attach Loader

Prepare To Attach

1. Center tractor between loader masts.

2. Stop tractor with backs of loader masts approximately 150 mm (6 in.) (A) in front of mounting frames.

3. Engage parking brake or place transmission in PARK and shut off engine.

A-Distance 150 mm (6 in.)

LD45720,000013B -19-27OCT08-1/14

A-Switch

causym CAUTION: Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids. If an accident occurs, see a doctor immediately to surgically remove any fluid injected into the skin. Fluid must be removed within a few hours to avoid gangrene. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A.

4. Turn key to ON position. Do not start tractor engine. Move loader control lever in all directions several times. (See your tractor operator's manual for specific procedures about relieving hydraulic pressure.)

5. If equipped with a mechanical lever and electro-hydraulic valve on third function (attachment, such as grapple), press switch (A) several times.

6. Turn key to OFF position.

Early Version

W08201

Later Version

W09661

5025, 5M Series, and 6D Series Tractors

LD45720,000013B -19-27OCT08-2/14

7. If equipped with Electronic Control Lever (E-ICV), release interlock. Operator's hand must be inserted to hold switch actuator (A) open.

8. Move loader control lever back and forth and side-to-side several times.

9. Turn key to OFF position.

A-Interlock Switch Actuator

LD45720,000013B -19-27OCT08-3/14

causym CAUTION: Avoid personal injury caused by unexpected loader movement. Hose connections must be correct to avoid unexpected movement when control lever is moved.

IMPORTANT: Before connecting coupler halves ensure that fittings are free of dirt and debris.

NOTE: Identify hose connections by color-coded caps and plugs on couplers. (If caps and plugs are missing, see IDENTIFY HOSE CONNECTIONS in the Service section.)

Attach Mid-Mount Couplers:

1. Remove dust caps on couplers.

2. Push and hold collar on female coupler.

3. Connect couplers.

4. Release collar on female coupler.

5. Repeat for all hydraulic hose connections.

6000 and 7000 Series Shown

LD45720,000013B -19-27OCT08-4/14

Attach Multi-Coupler:

1. Raise cover (A).

2. Push red knob (B) IN and rotate lever rearward and down, as shown.

A-Cover
B-Red Knob

LD45720,000013B -19-27OCT08-5/14

IMPORTANT: Multi-coupler mating halves must align properly or damage to couplers can occur.

3. Place loader coupler half (C), with chamfered edge (B) toward cover (A), onto tractor coupler (E). Make sure locating pins (D) on loader coupler fit into corresponding holes (F) in tractor coupler (E).

A-Cover
B-Chamfered Edge
C-Loader Coupler Half
D-Locating Pins
E-Tractor Coupler Half
F-Holes

LD45720,000013B -19-27OCT08-6/14

4. Rotate lever (A) to engage pins (C) on mobile coupler half (B) until a "click" is heard, locking halves together.

A-Lever
B-Mobile Coupler Half
C-Pin (1 each side)

LD45720,000013B -19-27OCT08-7/14

Attach Loader

1. If equipped with global cylinder latching system: Connect wiring harness connector (A).

2. Start tractor engine.

3. Place transmission in NEUTRAL , to allow tractor movement, and release parking brake.

A-Connector

Right-Hand Side

LD45720,000013B -19-27OCT08-8/14

4. Extend lift cylinders until pins (A) on loader masts are positioned over saddles (B) on mounting frames on each side.

A-Pin
B-Saddles

LD45720,000013B -19-27OCT08-9/14

5. Slowly dump bucket until masts (B) seat in mounting frames (A) on both sides, and stands (C) are slightly off ground.

6. Engage parking brake or place transmission in PARK and shut off engine.

A-Frame
B-Mast
C-Stands

LD45720,000013B -19-27OCT08-10/14

7. Remove spring locking pins (A), pins (B), and parking stands (C).

8. Remove quick lock pins and install parking stands (C) into each end of storage tube. Fasten with quick lock pins (D).

A-Spring Locking Pin
B-Pin
C-Parking Stands
D-Quick-Lock Pin

LD45720,000013B -19-27OCT08-11/14

9. Make sure mast bushings (A) are aligned with frame bushings (B) on both sides of loader.

A-Bushing, Mast
B-Bushing, Frame

LD45720,000013B -19-27OCT08-12/14

10. 5000 Series Tractors: Install mast pin (B) and spring locking pin (A) on both sides of loader. Fasten upper hose holder (C) to right-hand mast with spring locking pin (A).

5M Series Only: Fasten lower hose holder (D) to bracket with spring locking pin (A).

A-Spring Locking Pin
B-Mast Pin
C-Upper Hose Holder
D-Lower Hose Holder (5M Series Only)

Lower Hose Holder (5M Series Only)

LD45720,000013B -19-27OCT08-13/14

11. 6000 and 7000 Series Tractors: Install pin (E) on both sides of loader.

On right-hand side, position hydraulic hoses inside pin handle, as shown. Make sure hoses are inside guide (A).
Insert handle end through hose holder (D) and into slot (C).
Fasten with spring locking pin (B).

12. Start tractor and check loader operation.

A-Guide
B-Spring Locking Pin
C-Slot
D-Hose Holder
E-Pin

6000 and 7000 Series Tractors

LD45720,000013B -19-27OCT08-14/14