Detach Loader

CAUTION: Avoid personal injury caused by a falling loader. Always detach on a hard, level surface. Loader MUST be equipped with a bucket and parking stands.

2. Lower bucket to ground. Apply slight downward pressure. Do not raise tires off ground.

3. Engage parking brake or place transmission in PARK and shut off engine.

OUMX005,0001E20 -19-21OCT08-1/8

A-Upper Hose Holder
B-Spring Locking Pin
C-Pin
D-Parking Stand
E-Cylinder
F-Lower Hose Holder (5M Series Only)

NOTE: Bucket can be rolled back and forth to loosen pins (C).

4. Remove spring locking pin (B) and upper hose holder (A). Replace spring locking pin. 5M Series Only: Remove spring locking pin (B) and lower hose holder (F). Replace spring locking pin.

5. Remove spring locking pin (B) and pin (C) from both sides.

6. Remove parking stands (D) and replace quick-lock pins.

7. Use pins (C) and spring locking pins (B) to install stands in park position with base of stands parallel to ground. Place boards under stands if parked on soft ground.

8. Start tractor engine.

9. Place transmission in NEUTRAL , to allow tractor movement, and release parking brake.

OUMX005,0001E20 -19-21OCT08-2/8

11. Slowly roll back bucket until stands contact ground. Continue to roll back bucket until loader lifts out of mounting frames. Drive ahead as necessary to keep hoses slack.

OUMX005,0001E20 -19-21OCT08-3/8

A-Switch

CAUTION: Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids.

If an accident occurs, see a doctor immediately to surgically remove any fluid injected into the skin. Fluid must be removed within a few hours to avoid gangrene. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A.

12. Shut off engine. Turn key to ON position. Do not start tractor engine. Move loader control lever in all directions several times. (See your tractor operator's manual for specific procedures about relieving hydraulic pressure.)

13. If equipped with a mechanical lever and electro-hydraulic valve on third function (attachment, such as grapple), press switch (A) several times.

14. Turn key to OFF position.

OUMX005,0001E20 -19-21OCT08-4/8

16. Move loader control lever back and forth and side-to-side several times.

17. Turn key to OFF position.

A-Interlock Switch Actuator

OUMX005,0001E20 -19-21OCT08-5/8

A-Connector

OUMX005,0001E20 -19-21OCT08-6/8

a. Push and hold collar on female coupler.

b. Disconnect coupler.

c. Release collar on female coupler.

d. Install dust caps on couplers.

e. Repeat for all hydraulic hose connections.

f. Place hoses (A) on lift cylinder as shown. Do not place hoses on ground.

A-Hoses

OUMX005,0001E20 -19-21OCT08-7/8

IMPORTANT: Avoid seal damage. Relieve hydraulic pressure before multi-coupler disconnection. (See your tractor operator's manual.)

20. If equipped with multi-couplers perform the following:

a. Push red knob (A) IN and rotate lever rearward to disengage pins (B) and coupler halves.

b. Remove loader coupler half (C) from tractor coupler and insert pin into storage hole (D) on mast. Do not place hoses on ground.

IMPORTANT: Avoid damage from contact with tractor fender or wheel. Lever (E) must be in the locked (UP) position. Cover (F) must also be lowered to protect connection.

c. Rotate lever (E) forward until a click sound is heard. Lever must be in UP position.

d. Lower cover (F).

21. Place transmission in REVERSE and back tractor slowly away from loader.

A-Red Knob
B-Pin (1 each side)
C-Coupler Half with Hoses
D-Storage Hole
E-Lever
F-Cover

OUMX005,0001E20 -19-21OCT08-8/8