Every 50 Hours
Mounting Frame Hardware—6000 (Except 6403 and 6603) and 7000 Series Tractors with 4-Cylinder Engine
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W09430-UN-21MAY08
6D Series Tractors (Right-Hand Side Shown)
W08061-UN-21AUG06
All Other 4-Cylinder Tractors (Left-Hand Side Shown)
A - Cap Screws, M20
B - Cap Screws, M20
Tighten hardware (A and B) to specifications.
| Item | Measurement | Specification |
| Cap Screws (A) | Torque | 580 N•m (428 lb-ft) |
| Cap Screws (B) | Torque | 620 N•m (457 lb-ft) |
Mounting Frame Hardware—6000 and 7000 Series Tractors with 6-Cylinder Engine
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W08062-UN-21AUG06
Left-Hand Side Shown
A - Cap Screws, M20
B - Cap Screws, M20
Tighten hardware (A and B) to specifications.
| Item | Measurement | Specification |
| Cap Screws (A) | Torque | 620 N•m (457 lb-ft) |
| Cap Screws (B) | Torque | 580 N•m (428 lb-ft) |
Mounting Frame Hardware—6403 Tractors
IMPORTANT:
W23506-UN-25FEB13
Right-Hand Side Shown
W23507-UN-25FEB13
Torque Sequence (Left-Hand Side Shown)
A - Cap Screws, M20 x 55 mm
B - Washer, 21.4 x 42 x 5 mm
C - Cap Screws, M16 x 70 mm
D - Washer, 17 x 34 x 4 mm
E - Cap Screws, M16 x 50 mm
Avoid damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.Tighten hardware to specification in the sequence shown.
| Item | Measurement | Specification |
| M20 Cap Screws (A) | Torque | 530 N•m (391 lb-ft) |
| M16 Cap Screws (C) and (E) | Torque | 275 N•m (203 lb-ft) |
Mounting Frame Hardware—6603 Tractors
IMPORTANT:
W23508-UN-25FEB13
Right-Hand Side Shown
W23509-UN-25FEB13
Torque Sequence (Left-Hand Side Shown)
W23710-UN-21MAY13
A - Cap Screws, M20 x 55 mm
B - Washer, 21.4 x 42 x 5 mm
C - Cap Screws, M16 x 70 mm
D - Washer, 17 x 34 x 4 mm
E - Cap Screws, M16 x 50 mm
F - Cap Screw, M20 x 40 mm
Avoid damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.Tighten hardware to specification in the sequence shown.
| Item | Measurement | Specification |
| M20 Cap Screws (A) | Torque | 530 N•m (391 lb-ft) |
| M16 Cap Screws (C) and (E) | Torque | 275 N•m (203 lb-ft) |
| M20 Cap Screw (F) | Torque | 200 N•m (148 lb-ft) |
Mounting Frame Hardware—5200, 5300, and 5400 Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W09920-UN-17SEP08
A - Cap Screws, M16 x 50
B - Cap Screw, M20 x 65
C - Spacer
Tighten hardware (A and B) to specifications.
|
Mounting Frame Hardware |
|||
|---|---|---|---|
|
Location |
Description |
Size |
Torque Specification |
|
A |
Cap Screw Flat Washer |
M16 x 50 17 x 34 x 4 mm |
275 N•m (200 lb-ft) |
|
B |
Cap Screw Flat Washer |
M20 x 65 21 x 42 x 5 mm |
530 N•m (400 lb-ft) |
|
C |
Spacer |
||
Mounting Frame Hardware—5210, 5220, 5310, and 5320 Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W09919-UN-17SEP08
A - Cap Screw, M16 x 50
B - Cap Screw, M20 x 65
C - Spacer
D - Cap Screw, M16 x 70
Tighten hardware (A, B, and D) to specifications.
|
Mounting Frame Hardware |
|||
|---|---|---|---|
|
Location |
Description |
Size |
Torque Specification |
|
A |
Cap Screw Flat Washer |
M16 x 50 17 x 34 x 4 mm |
275 N•m (200 lb-ft) |
|
B |
Cap Screw Flat Washer |
M20 x 65 21 x 42 x 5 mm |
530 N•m (400 lb-ft) |
|
C |
Spacer |
||
|
D |
Cap Screw Flat Washer |
M16 x 70 17 x 34 x 4 mm |
275 N•m (200 lb-ft) |
Mounting Frame Hardware—5500 Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W09905-UN-16SEP08
A - Mounting Frame
B - Cross Tie
C - Cap Screws, M16 x 50
D - Cap Screw, M20 x 65
E - Spacer
F - Cap Screw, M20 x 65
Tighten hardware (C, D, and F) to specifications.
|
Mounting Frame Hardware |
|||
|---|---|---|---|
|
Location |
Description |
Size |
Torque Specification |
|
C |
Cap Screw Flat Washer |
M16 x 50 17 x 34 x 4 mm |
275 N•m (200 lb-ft) |
|
D |
Cap Screw Flat Washer |
M20 x 65 21 x 42 x 5 mm |
530 N•m (400 lb-ft) |
|
F |
Cap Screw Flat Washer Flange Nut |
M20 x 65 21 x 42 x 5 mm M20 |
530 N•m (400 lb-ft) |
Mounting Frame Hardware—5410, 5420, 5510, and 5520 Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W09912-UN-16SEP08
A - Mounting Frame
B - Cross Tie
C - Cap Screw, M16 x 50
D - Cap Screws, M20 x 65
E - Spacer
F - Cap Screws, M20 x 65
G - Cap Screw, M16 x 70
Tighten hardware (C, D, F, and G) to specifications.
|
Mounting Frame Hardware |
|||
|---|---|---|---|
|
Location |
Description |
Size |
Torque Specification |
|
C |
Cap Screw Flat Washer |
M16 x 50 17 x 34 x 4 mm |
275 N•m (200 lb-ft) |
|
D |
Cap Screw Flat Washer |
M20 x 65 21 x 42 x 5 mm |
530 N•m (400 lb-ft) |
|
F |
Cap Screw Flat Washer Flange Nut |
M20 x 65 21 x 42 x 5 mm M20 |
530 N•m (400 lb-ft) |
|
G |
Cap Screw Flat Washer |
M16 x 70 17 x 34 x 4 mm |
275 N•m (200 lb-ft) |
Mounting Frame Hardware—5225 and 5325 Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W09956-UN-23SEP08
W09802-UN-27AUG08
A - Cap Screw, M20 x 100 (2 used)
B - Cap Screw, M20 x 90 (2 used)
C - Cap Screw, M20 x 55 (2 used)
D - Washer, 21.4 x 42 x 5 mm (4 used)
E - Spacer, 23 x 50 mm (2 used)
Tighten hardware to specifications in the sequence shown.
| Item | Measurement | Specification |
| Hardware (A and B) | Torque | 610 N•m (450 lb-ft) |
| Hardware (C) | Torque | 530 N•m (390 lb-ft) |
Mounting Frame Hardware—5425, 5525, 5603, 5083E, 5093E, 5101E, 5625, and 5725PR Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W09957-UN-23SEP08
W09960-UN-23SEP08
A - Cap Screw, M20 x 55, (4 used)
B - Washer, 21.4 x 42 x 5 mm, (6 used)
C - Cap Screw, M20 x 90, (2 used)
Tighten hardware to specifications in the sequence shown.
| Item | Measurement | Specification |
| Cap Screw (A) | Torque | 530 N•m (390 lb-ft) |
| Cap Screw (C) | Torque | 610 N•m (450 lb-ft) |
Mounting Frame Hardware—5065M, 5075M, 5085M, 5095M, and 5105M Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
NOTE: Side exhaust pipe (B) (if equipped) must be removed to access the left-hand mounting frame cap screws.
W20532-UN-30SEP09
W20039-UN-20OCT08
Side Exhaust—Left-Hand Side (If Equipped)
A - Cap Screw, M20 x 110, (5 each side)
B - Side Exhaust Pipe
C - Clamp
If equipped with side exhaust pipe (B): Loosen clamp (C) and remove pipe to access left-hand mounting frame cap screws.Tighten hardware to specification in the sequence shown.
| Item | Measurement | Specification |
| Cap Screw (A) | Torque | 625 N•m (460 lb-ft) |
Replace exhaust pipe and tighten clamp.
Mounting Frame Hardware—5070M, 5080M, 5090M, and 5100M Tractors
IMPORTANT: Help prevent damage to the tractor or loader caused by operating with loose mounting hardware. Tighten loader mounting frame hardware after the first 10 hours of operation and again after every 50 hours.
W20531-UN-01OCT09
5070M, 5080M, 5090M, and 5100M Tractors
Tighten hardware (A and B) to specifications in the sequence shown.
| Item | Measurement | Specification |
| Cap Screws (A) | Torque | 580 N•m (428 lb-ft) |
| Cap Screws (B) | Torque | 620 N•m (457 lb-ft) |
|
OUO6064,0000B2B-19-20130607 |
