Attach Loader

  1. W09842
    W09842-UN-02SEP08

    A - Distance 150 mm (6 in.)

    Center tractor between loader masts.


  2. Stop tractor with backs of loader masts approximately 150 mm (6 in.) (A) in front of mounting frames.

  3. Engage parking brake or place transmission in PARK and shut off engine.

  4. CAUTION:

    X9811
    X9811-UN-23AUG88

    W03317
    W03317-UN-31MAR99

    W08200
    W08200-UN-22SEP06

    Early Version

    W08201
    W08201-UN-22SEP06

    Later Version

    W09661
    W09661-UN-17JUL08

    5025, 5M Series, and 6D Series Tractors

    A - Switch

    Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids. If an accident occurs, see a doctor immediately to surgically remove any fluid injected into the skin. Fluid must be removed within a few hours to avoid gangrene. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A.

    Turn key to ON position. Do not start tractor engine. Move loader control lever in all directions several times. (See your tractor operator's manual for specific procedures about relieving hydraulic pressure.)


  5. If equipped with a mechanical lever and electrohydraulic valve on third function (attachment, such as grapple): Press switch (A) several times.

  6. Turn key to OFF position.

  7. W08193
    W08193-UN-20SEP06

    A - Interlock Switch Actuator

    If equipped with Electronic Control Lever (E-ICV): Release interlock. Operator’s hand must be inserted to hold switch actuator (A) open.


  8. Move loader control lever back and forth and side-to-side several times.

  9. Turn key to OFF position.

  10. CAUTION:

    W08003
    W08003-UN-10JUN08

    6000 and 7000 Series Shown

    W21247
    W21247-UN-02DEC10

    5E Series Tractors (Two-Function Shown)

    Avoid personal injury caused by unexpected loader movement. Hose connections must be correct to avoid unexpected movement when control lever is moved.

    IMPORTANT: Before connecting coupler halves ensure that fittings are free of dirt and debris.

    NOTE: Identify hose connections by color-coded caps and plugs on couplers. (If caps and plugs are missing, see IDENTIFY HOSE CONNECTIONS in the Service section.)

    If equipped with Mid-Mount Couplers:

    1. Remove dust caps on couplers.

    2. Push and hold collar on female coupler.

    3. Connect couplers.

    4. Release collar on female coupler.

    5. Repeat for all hydraulic hose connections.


  11. W08014
    W08014-UN-08AUG06

    A - Cover

    B - Red Knob

    If equipped with Multicoupler:

    1. Raise cover (A).

    2. Push red knob (B) IN and rotate lever rearward and down, as shown.


    3. IMPORTANT:

      W08015
      W08015-UN-09AUG06

      W08017
      W08017-UN-09AUG06

      A - Cover

      B - Chamfered Edge

      C - Loader Coupler Half

      D - Locating Pins

      E - Tractor Coupler Half

      F - Holes

      Multicoupler mating halves must align properly or damage to couplers can occur.

      Place loader coupler half (C), with chamfered edge (B) toward cover (A), onto tractor coupler (E). Make sure locating pins (D) on loader coupler fit into corresponding holes (F) in tractor coupler (E).


    4. W08018
      W08018-UN-09AUG06

      A - Lever

      B - Loader Coupler Half

      C - Pin (1 each side)

      Rotate lever (A) to engage pins (C) on loader coupler half (B), locking halves together.


  12. W08096
    W08096-UN-01SEP06

    Right-Hand Side

    A - Connector (if equipped)

    If equipped with Global Cylinder Latching System: Connect wiring harness connector (A).


  13. Start tractor engine.

  14. Place transmission in NEUTRAL, to allow tractor movement, and release parking brake.

  15. W20083
    W20083-UN-16OCT08

    A - Pin (1 each side)

    B - Saddle (1 each side)

    Extend lift cylinders until pins (A) on loader masts are positioned over saddles (B) on mounting frames on each side.


  16. W09850
    W09850-UN-06OCT08

    A - Frame

    B - Mast

    C - Parking Stands

    Slowly dump bucket until masts (B) seat in mounting frames (A) on both sides, and stands (C) are slightly off ground.


  17. Engage parking brake or place transmission in PARK and shut off engine.

  18. W09848
    W09848-UN-03SEP08

    W20546
    W20546-UN-13OCT09

    Right-Hand Side Shown

    A - Spring Locking Pin (1 each side)

    B - Mast Pin (1 each side)

    C - Parking Stand (1 each side)

    D - Quick-Lock Pin (1 each side)

    Remove spring locking pins (A), mast pins (B), and parking stands (C).


  19. Remove quick lock pins (D) and install parking stands (C) into each end of storage tube. Fasten with quick lock pins.

  20. W20085
    W20085-UN-21OCT08

    A - Bushing, Mast

    B - Bushing, Frame

    Make sure mast bushings (A) are aligned with frame bushings (B) on both sides of loader.


  21. 5000 Series Tractors:

    W20526
    W20526-UN-29SEP09

    5000 Series Tractors

    W20529
    W20529-UN-29SEP09

    Bottom Holder—5065M, 5075M, 5085M, 5095M, and 5105M Tractors

    A - Spring Locking Pin

    B - Upper Hose Holder

    C - Mast Pin (1 each side)

    D - Spring Locking Pin (1 each side)

    E - Bottom Hose Holder

    F - Spring Locking Pin

    Install mast pin (C) and spring locking pin (D) on both sides of loader. Fasten upper hose holder (B) to right-hand mast with spring locking pin (A).

    5065M, 5075M, 5085M, 5095M, and 5105M Tractors: Fasten bottom hose holder (E) to bracket using spring locking pin (F).


  22. W20524
    W20524-UN-08OCT09

    A - Guide

    B - Slot, Front (1 each side)

    C - Spring Locking Pin (1 each side)

    D - Hose Holder

    E - Mast Pin (1 each side)

    5070M, 5080M, 5090M, and 5100M Tractors: Install mast pins (E) on both sides of loader as follows:

    • On right-hand side, position hydraulic hoses inside pin handle, as shown. Make sure hoses are inside guide (A).
    • Insert handle end through hose holder (D) and into front slot (B) in mast.
    • Fasten with spring locking pin (C).


  23. W09546
    W09546-UN-09JUN08

    6D, 6000, 6003, and 7000 Series Tractors

    A - Guide

    B - Spring Locking Pin (1 each side)

    C - Slot, Front (1 each side)

    D - Hose Holder

    E - Mast Pin (1 each side)

    6D, 6000, 6003, and 7000 Series Tractors: Install mast pins (E) on both sides of loader as follows:

    • On right-hand side, position hydraulic hoses inside mast pin handle, as shown. Make sure hoses are inside guide (A).
    • Insert handle end through hose holder (D) and into front slot (C) in mast.
    • Fasten with spring locking pin (B).


  24. Start tractor engine and check loader operation.

OUO6064,0000B80-19-20130607