Detach Loader

  1. CAUTION:

    W14000
    W14000-UN-05OCT88

    To help prevent personal injury caused by a falling loader, always detach on a hard, level surface. Loader MUST be equipped with a bucket and parking stands.

    W09472
    W09472-UN-13JUN08

    Dump bucket approximately 40° below level.


  2. Lower bucket to ground, applying slight downward pressure. Do not raise tires off ground.

  3. Engage parking brake or place transmission in PARK and shut off engine.

  4. NOTE:

    W09541
    W09541-UN-09JUN08

    Right-Hand Side Shown

    A - Spring Locking Pin

    B - Pin

    Bucket can be rolled back and forth to loosen pins (B).

    Remove spring locking pin (A) and pin (B) from loader mast on both sides.


  5. W09542
    W09542-UN-09JUN08

    W08000
    W08000-UN-28AUG06

    A - Quick-Lock Pin (2 used)

    B - Parking Stands

    C - Spring Locking Pin (2 used)

    D - Mast Pin (2 used)

    E - Storage Bracket (1 each side)

    Remove quick-lock pins (A) and parking stands (B). Install quick lock pins on storage brackets (E).


  6. Align holes in bracket and top of parking stand and install mast pin (D) as shown. Fasten with spring locking pin (C).

  7. Start tractor engine.

  8. NOTE: To prevent loader from sinking in soft ground, place boards under parking stands.

    Place transmission in NEUTRAL, to allow tractor movement, and release parking brake.

  9. Extend lift cylinders until masts move forward.

  10. W09543
    W09543-UN-13JUN08

    Slowly roll back bucket until stands contact ground. Continue to roll back bucket until loader lifts out of mounting frames. Drive ahead as necessary to keep hoses slack.


  11. CAUTION:

    X9811
    X9811-UN-23AUG88

    Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids.

    If an accident occurs, see a doctor immediately to surgically remove any fluid injected into the skin. Fluid must be removed within a few hours to avoid gangrene. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A.

    W03317
    W03317-UN-31MAR99

    W08200
    W08200-UN-22SEP06

    Early Version

    W08201
    W08201-UN-22SEP06

    Later Version

    W09661
    W09661-UN-17JUL08

    6D Series Tractors

    A - Switch

    Shut off engine, turn key on, and move loader control lever back and forth and side-to-side several times. (See your tractor Operator’s Manual.)


  12. If equipped with Mechanical Lever with Electrohydraulic Valve on Third Function (attachment, such as grapple):

    1. Turn key to ON position. Do not start tractor engine.

    2. Press switch (A) several times.

    3. Turn key to OFF position.

  13. W08193
    W08193-UN-20SEP06

    A - Interlock Switch Actuator

    If equipped with Electronic Control Lever (E-ICV):

    1. Turn key to ON position. Do not start tractor engine.

    2. Release interlock. (Operator’s hand must be inserted to hold switch actuator (A) open.)

    3. Move loader control lever back and forth and side-to-side several times.

    4. Turn key to OFF position.


  14. W08096
    W08096-UN-01SEP06

    Right-Hand Side

    A - Connector

    If equipped with Global Cylinder Latching System: Disconnect wiring harness connector (A).


  15. W08003
    W08003-UN-10JUN08

    W08009
    W08009-UN-09AUG06

    A - Hoses

    If equipped with Mid-Mount Couplers:

    1. Push and hold collar on female coupler.

    2. Disconnect coupler.

    3. Release collar on female coupler.

    4. Place cap on hose end and plug in coupler.

    5. Repeat for all hydraulic hose connections.

    6. Place hoses (A) on lift cylinder as shown. Do not place hoses on ground.


  16. IMPORTANT:

    W08008
    W08008-UN-09AUG06

    W08394
    W08394-UN-22NOV06

    A - Red Knob

    B - Pin (1 each side)

    C - Coupler Half with Hoses

    D - Storage Hole

    Avoid seal damage. Relieve hydraulic pressure before disconnecting multi-coupler. (See your tractor Operator’s Manual.)

    If equipped with Multi-Coupler:

    1. Push red knob (A) IN and rotate lever rearward to disengage pins (B), separating coupler halves.

    2. Remove loader coupler half with hoses (C) away from tractor coupler and insert pin into storage hole (D) on mast as shown. Do not place hoses on ground.


    3. IMPORTANT:

      W08011
      W08011-UN-14AUG06

      A - Lever

      B - Cover

      Lever (A) must be in the locked (UP) position when loader coupler half with hoses are removed to avoid interference with tractor fender or wheel. Cover (B) must also be lowered to protect connection surface of tractor coupler half.

      Rotate lever (A) around and forward until it locks in UP position, as shown.

    4. Lower cover (B).


  17. Place transmission in REVERSE and move tractor slowly away from loader.

OUMX005,0001F0E-19-20080718