Attach Loader

  1. W09544
    W09544-UN-13JUN08

    A - Mast Distance from Mounting Frames

    Center tractor between loader masts.


  2. Stop tractor with backs of loader masts approximately 150 mm (6 in.) (A) in front of mounting frames.

  3. Engage parking brake or place transmission in PARK and shut off engine.

  4. CAUTION: Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids.

    If an accident occurs, see a doctor immediately to surgically remove any fluid injected into the skin. Fluid must be removed within a few hours to avoid gangrene. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A.

    X9811
    X9811-UN-23AUG88

    W03317
    W03317-UN-31MAR99

    W08200
    W08200-UN-22SEP06

    Early Version

    W08201
    W08201-UN-22SEP06

    Later Version

    W09661
    W09661-UN-17JUL08

    6D Series Tractors

    A - Switch

    Move loader control lever back and forth and side-to-side several times. (See your tractor Operator’s Manual.)


  5. If equipped with Mechanical Lever with Electrohydraulic valve/third function (attachment, such as grapple):

    1. Turn key to ON position. Do not start tractor engine.

    2. Press switch (A) several times.

    3. Turn key to OFF position.

  6. W08193
    W08193-UN-20SEP06

    A - Interlock Switch Actuator

    If equipped with Electronic Control Lever (E-ICV):

    1. Turn key to ON position. Do not start tractor engine.

    2. Release interlock. (Operator’s hand must be inserted to hold switch actuator (A) open.)

    3. Move loader control lever back and forth and side-to-side several times.

    4. Turn key to OFF position.


  7. CAUTION: Avoid personal injury caused by unexpected loader movement. Hose connections must be correct for loader to respond as expected when control lever is moved.

    IMPORTANT: Before connecting coupler halves make sure that fittings are free of dirt and debris.

    NOTE: Hose connections are identified by matching the color-coded cap on the hose end with the same color-coded plug on the coupler. (If caps and plugs are missing, see IDENTIFY HOSE CONNECTIONS in the Service section.)

    W08003
    W08003-UN-10JUN08

    If equipped with Mid-Mount Couplers:

    1. Push and hold collar on female coupler.

    2. Insert hydraulic hose with male end into coupler.

    3. Release collar on female coupler.

    4. Repeat for all hydraulic hose connections.


  8. W08014
    W08014-UN-08AUG06

    A - Cover

    B - Red Knob

    If equipped with Multi-Coupler:

    1. Raise cover (A).

    2. Push red knob (B) IN and rotate lever rearward and down, as shown.


    3. IMPORTANT:

      W08015
      W08015-UN-09AUG06

      W08017
      W08017-UN-09AUG06

      A - Cover

      B - Chamfered Edge

      C - Loader Coupler Half

      D - Locating Pins

      E - Tractor Coupler Half

      F - Holes

      Multi-coupler mating halves must align properly or damage to couplers can occur.

      Place loader coupler half (C), with chamfered edge (B) toward cover (A), onto tractor coupler (E). Make sure locating pins (D) on loader coupler fit into corresponding holes (F) in tractor coupler (E).


    4. W08018
      W08018-UN-09AUG06

      A - Lever

      B - Mobile Coupler Half

      C - Pin (1 each side)

      Rotate lever (A) to engage pins (C) on mobile coupler half (B) locking halves together.


  9. W08096
    W08096-UN-01SEP06

    Right-Hand Side

    A - Connector

    If equipped with global cylinder latching system: Connect wiring harness connector (A).


  10. Start tractor engine.

  11. Place transmission in NEUTRAL, to allow tractor movement, and release parking brake.

  12. W09560
    W09560-UN-13JUN08

    A - Pin

    B - Hook

    Extend lift cylinders until pins (A) on loader masts are positioned over hooks (B) on mounting frames on each side.


  13. W09545
    W09545-UN-13JUN08

    A - Frame

    B - Mast

    C - Stands

    Slowly dump bucket until masts (B) seat in mounting frames (A) on both sides, and stands (C) are slightly off ground.


  14. Engage parking brake or place transmission in PARK and shut off engine.

  15. W08021
    W08021-UN-11AUG06

    A - Spring Locking Pin

    B - Pin

    C - Parking Stands

    Remove spring locking pins (A), pins (B) and parking stands (C).


  16. W08022
    W08022-UN-18SEP06

    A - Storage Tube

    B - Parking Stand (1 each side)

    C - Quick Lock Pin (1 each side)

    Remove quick lock pins and install parking stands (B) into each end of storage tube (A). Fasten with quick lock pins (C).


  17. W09561
    W09561-UN-13JUN08

    A - Bushing, Mast

    B - Bushing, Frame

    Make sure mast bushings (A) are aligned with frame bushings (B) on both sides of loader.


  18. W09546
    W09546-UN-09JUN08

    Right-Hand Side Shown

    A - Guide

    B - Spring Locking Pin

    C - Slot

    D - Hose Holder

    E - Pin

    Install pin (E) on both sides of loader:

    • Left-Hand Side:
      1. Install pin (E). Insert handle end into slot (C).
      2. Fasten with spring locking pin (B).
    • Right-Hand Side:
      1. Install pin (E).
      2. Position hydraulic hoses inside pin handle, as shown. Make sure hoses are inside guide (A).
      3. Insert handle end through hose holder (C) and into slot (B).
      4. Fasten with spring locking pin (E).


  19. Start tractor and check loader operation.

OUMX005,0001F0F-19-20080721